Airplane safety

Aviation safety is the study and practice of managing risks in aviation. This includes preventing aviation accidents and incidents through research, educating air travel personnel, passengers and the general public, as well as the design of aircraft and aviation infrastructure. The aviation industry is subject to significant regulation and oversight.

Aviation security is focused on protecting air travelers, aircraft and infrastructure from intentional harm or disruption, rather than unintentional mishaps.

Statistics

Evolution

In 1926 and 1927, there were a total of 24 fatal commercial airline crashes, a further 16 in 1928, and 51 in 1929 (killing 61 people), which remains the worst year on record at an accident rate of about 1 for every flown. Based on the current numbers flying, this would equate to 7,000 fatal incidents per year.

For the ten-year period 2002 to 2011, 0.6 fatal accidents happened per one million flights globally, 0.4 per million hours flown, 22.0 fatalities per one million flights or 12.7 per million hours flown.

From 310 million passengers in 1970, air transport had grown to 3,696 million in 2016, led by 823 million in the United States, then 488 million in China.
In 2016, there were 19 fatal accidents of civil airliners of more than 14 passengers, resulting in 325 fatalities, the second safest year ever after 2015 with 16 accidents and 2013 with 265 fatalities.
For planes heavier than 5.7 t, there were 34.9 million departures and 75 accidents worldwide with 7 of these fatal for 182 fatalities, the lowest since 2013 : fatalities per million departures.

In 2017, there were 10 fatal airliner accidents, resulting in 44 occupant fatalities and 35 persons on the ground: the safest year ever for commercial aviation, both by the number of fatal accidents as well as in fatalities.

By 2019, fatal accidents per million flights decreased 12 fold since 1970, from 6.35 to 0.51, and fatalities per trillion revenue passenger kilometre (RPK) decreased 81 fold from 3,218 to 40.

Typology

Runway safety represents % of accidents, ground safety % and loss of control in-flight %.

The main cause is human error. Safety has improved from better aircraft design process, engineering and maintenance, the evolution of navigation aids, and safety protocols and procedures.

Transport comparisons

There are three main ways in which risk of fatality of a certain mode of travel can be measured:
Deaths per billion typical ''journeys'' taken, deaths per billion ''hours'' traveled, or deaths per billion ''kilometers'' traveled. The following table displays these statistics for the United Kingdom 1990–2000. Note that aviation safety does not include travelling to the airport.

The first two statistics are computed for typical travels for respective forms of transport, so they cannot be used directly to compare risks related to different forms of transport in a particular travel "from A to B". For example: according to statistics, a typical flight from Los Angeles to New York will carry a larger risk factor than a typical car travel from home to office. But a car travel from Los Angeles to New York would not be typical. It would be as large as several dozens of typical car travels, and associated risk will be larger as well. Because the journey would take a much longer time, the overall risk associated by making this journey by car will be higher than making the same journey by air, even if each individual hour of car travel can be less risky than an hour of flight.

It is therefore important to use each statistic in a proper context. When it comes to a question about risks associated with a particular long-range travel from one city to another, the most suitable statistic is the third one, thus giving a reason to name air travel as the safest form of long-range transportation. However, if the availability of an air option makes an otherwise inconvenient journey possible, then this argument loses some of its force.

Aviation industry insurers base their calculations on the ''deaths per journey'' statistic while the aviation industry itself generally uses the ''deaths per kilometre'' statistic in press releases.

Since 1997, the number of fatal air accidents has been no more than 1 for every 2,000,000,000 person-miles flown (e.g., 100 people flying a plane for counts as 100,000 person-miles, making it comparable with methods of transportation with different numbers of passengers, such as one person driving an automobile for , which is also 100,000 person-miles), and thus one of the safest modes of transportation when measured by distance traveled.

The death per billion hours when skydiving assume a 6 minutes skydive (not accounting for the plane ascent). The death per billion journey when paragliding assume an average flight of 15 minutes, so 4 flights per hour.

The Economist notes that air travel is safer by distance travelled, but trains are as safe as planes; and cars four times more hazardous for deaths per time travelled, and cars and trains are respectively three times and six times safer than planes by number of journeys taken.

Because the above figures are focused on providing a perspective to the realm of everyday transportation, air travel is taken to include only standard civil passenger aviation, as offered commercially to the general public. Military and special-purpose aircraft are excluded.

United States

Between 1990 and 2015, there were 1874 commuter and air taxi accidents in the U.S. of which 454 (%) were fatal, resulting in 1296 deaths, including 674 accidents (36%) and 279 fatalities (22%) in Alaska alone.

The number of deaths per passenger-mile on commercial airlines in the United States between 2000 and 2010 was about 0.2 deaths per 10 billion passenger-miles. For driving, the rate was 150 per 10 billion vehicle-miles for 2000 : 750 times higher per mile than for flying in a commercial airplane.

There were no fatalities on large scheduled commercial airlines in the United States for over nine years, between the Colgan Air Flight 3407 crash in February 2009, and a catastrophic engine failure on Southwest Airlines Flight 1380 in April 2018.

Security

Another aspect of safety is protection from intentional harm or property damage, also known as ''security''.

The terrorist attacks of 2001 are not counted as accidents. However, even if they were counted as accidents they would have added about 1 death per billion person-miles. Two months later, American Airlines Flight 587 crashed in New York City, killing 265 people, including 5 on the ground, causing 2001 to show a very high fatality rate. Even so, the rate that year including the attacks (estimated here to be about 4 deaths per billion person-miles), is safe compared to some other forms of transport when measured by distance traveled.

History

Before WWII

The first aircraft electrical or electronic device avionics system was Lawrence Sperry's autopilot, demonstrated in June 1914.

The Transcontinental Airway System chain of beacons was built by the Commerce Department in 1923 to guide airmail flights.

Gyrocopters were developed by Juan de la Cierva to avoid stall and spin accidents, and for that invented cyclic and collective controls used by helicopters. The first flight of a gyrocopter was on 17 January 1923.

During the 1920s, the first laws were passed in the US to regulate civil aviation, notably the Air Commerce Act of 1926 which required pilots and aircraft to be examined and licensed, for accidents to be properly investigated, and for the establishment of safety rules and navigation aids, under the Aeronautics Branch of the United States Department of Commerce.

A network of aerial lighthouses was established in the United Kingdom and Europe during the 1920s and 1930s. Use of the lighthouses has declined with the advent of radio navigation aids such as NDB (Non-directional beacon), VOR (VHF omnidirectional ranging) and DME (distance measuring equipment). The last operational aerial lighthouse in the United Kingdom is on top of the cupola over the RAF College main hall at RAF Cranwell.

One of the first aids for air navigation to be introduced in the US in the late 1920s was airfield lighting to assist pilots to make landings in poor weather or after dark. The Precision Approach Path Indicator was developed from this in the 1930s, indicating to the pilot the angle of descent to the airfield. This later became adopted internationally through the standards of the International Civil Aviation Organization (ICAO).

Jimmy Doolittle developed Instrument rating and made his first "blind" flight in September 1929.
The March 1931 wooden wing failure of a Transcontinental & Western Air Fokker F-10 carrying Knute Rockne, coach of the University of Notre Dame's football team, reinforced all-metal airframes and led to a more formal accident investigation system.
On Sept. 4, 1933, a Douglas DC-1 test flight was conducted with one of the two engines shut down during the takeoff run, climbed to , and completed its flight, proving twin aircraft engine safety.
With greater range than lights and weather immunity, radio navigation aids were first used in the 1930s, like the Australian Aeradio stations guiding transport flights, with a light beacon and a modified Lorenz beam transmitter (the German blind-landing equipment preceding the modern instrument landing system - ILS).
ILS was first used by a scheduled flight to make a landing in a snowstorm at Pittsburgh, Pennsylvania, in 1938, and a form of ILS was adopted by the ICAO for international use in 1949.

WWII and later

Hard runways were built worldwide for World War II to avoid waves and floating hazards plaguing seaplanes.

Developed by the U.S. and introduced during World War II, LORAN replaced the sailors' less reliable compass and celestial navigation over water and survived until it was replaced by the Global Positioning System.

Following the development of radar in World War II, it was deployed as a landing aid for civil aviation in the form of ground-controlled approach (GCA) systems then as the airport surveillance radar as an aid to air traffic control in the 1950s.

A number of ground-based weather radar systems can detect areas of severe turbulence.

A modern Honeywell Intuvue weather system visualizes weather patterns up to away.

Distance measuring equipment (DME) in 1948 and VHF omnidirectional range (VOR) stations became the main route navigation means during the 1960s, superseding the low frequency radio ranges and the non-directional beacon (NDB): the ground-based VOR stations were often co-located with DME transmitters and the pilots could establish their bearing and distance to the station.

With the arrival of Wide Area Augmentation System (WAAS), satellite navigation has become accurate enough for altitude as well as positioning use, and is being used increasingly for instrument approaches as well as en-route navigation. However, because the GPS constellation is a single point of failure, on-board Inertial Navigation System (INS) or ground-based navigation aids are still required for backup.

In 2017, Rockwell Collins reported it had become more costly to certify than to develop a system, from 75% engineering and 25% certification in past years.
It calls for a global harmonization between certifying authorities to avoid redundant engineering and certification tests rather than recognizing the others approval and validation.

Groundings of entire classes of aircraft out of equipment safety concerns is unusual, but this has occurred to the de Havilland Comet in 1954 after multiple crashes due to metal fatigue and hull failure, the McDonnell Douglas DC-10 in 1979 after the crash of American Airlines Flight 191 due to engine loss, the Boeing 787 Dreamliner in 2013 after its battery problems, and the Boeing 737 MAX in 2019 after two crashes preliminarily tied to a flight control system.

Aviation safety hazards

Unapproved parts

Parts manufactured without an aviation authority's approval are described as "unapproved". Unapproved parts include inferior counterfeits, those used beyond their time limits, those that were previously approved but not properly returned to service, those with fraudulent labels, production overruns that were not sold with the agency's permission, and those that are untraceable. Unapproved faulty parts have caused hundreds of incidents and crashes, some fatal, including about 24 crashes between 2010 and 2016.

Foreign object debris

Foreign object debris (FOD) includes items left in the aircraft structure during manufacture/repairs, debris on the runway and solids encountered in flight (e.g. hail and dust). Such items can damage engines and other parts of the aircraft. In 2000, Air France Flight 4590 crashed after hitting a part that had fallen from a departing Continental Airlines DC-10.

Misleading information and lack of information

A pilot misinformed by a printed document (manual, map, etc.), reacting to a faulty instrument or indicator (in the cockpit or on the ground), or following inaccurate instructions or information from flight or ground control can lose situation awareness, or make errors, and accidents or near misses may result. The crash of Air New Zealand Flight 901 was a result of receiving and interpreting incorrect coordinates, which caused the pilots to inadvertently fly into a mountain.

Lightning

Boeing studies showed that airliners are struck by lightning twice per year on average; aircraft withstand typical lightning strikes without damage.

The dangers of more powerful positive lightning were not understood until the destruction of a glider in 1999. It has since been suggested that positive lightning might have caused the crash of Pan Am Flight 214 in 1963. At that time, aircraft were not designed to withstand such strikes because their existence was unknown. The 1985 standard in force in the US at the time of the glider crash, Advisory Circular AC 20-53A, was replaced by Advisory Circular AC 20-53B in 2006. However, it is unclear whether adequate protection against positive lightning was incorporated.

The effects of typical lightning on traditional metal-covered aircraft are well understood and serious damage from a lightning strike on an airplane is rare. The Boeing 787 Dreamliner of which the exterior is carbon-fiber-reinforced polymer received no damage from a lightning strike during testing.

Ice and snow

Ice and snow can be major factors in airline accidents. In 2005, Southwest Airlines Flight 1248 slid off the end of a runway after landing in heavy snow conditions, killing one child on the ground.

Even a small amount of icing or coarse frost can greatly impair the ability of a wing to develop adequate lift, which is why regulations prohibit ice, snow or even frost on the wings or tail, prior to takeoff. Air Florida Flight 90 crashed on takeoff in 1982, as a result of ice/snow on its wings.

An accumulation of ice during flight can be catastrophic, as evidenced by the loss of control and subsequent crashes of American Eagle Flight 4184 in 1994, and Comair Flight 3272 in 1997. Both aircraft were turboprop airliners, with straight wings, which tend to be more susceptible to inflight ice accumulation, than are swept-wing jet airliners.

Airlines and airports ensure that aircraft are properly de-iced before takeoff whenever the weather involves icing conditions. Modern airliners are designed to prevent ice buildup on wings, engines, and tails (empennage) by either routing heated air from jet engines through the leading edges of the wing, and inlets, or on slower aircraft, by use of inflatable rubber "boots" that expand to break off any accumulated ice.

Airline flight plans require airline dispatch offices to monitor the progress of weather along the routes of their flights, helping the pilots to avoid the worst of inflight icing conditions. Aircraft can also be equipped with an ice detector in order to warn pilots to leave unexpected ice accumulation areas, before the situation becomes critical. Pitot tubes in modern airplanes and helicopters have been provided with the function of "Pitot Heating" to prevent accidents like Air France Flight 447 caused by the pitot tube freezing and giving false readings.

Wind shear or microburst

A wind shear is a change in wind speed and/or direction over a relatively short distance in the atmosphere. A microburst is a localized column of sinking air that drops down in a thunderstorm. Both of these are potential weather threats that may cause an aviation accident.

Strong outflow from thunderstorms causes rapid changes in the three-dimensional wind velocity just above ground level. Initially, this outflow causes a headwind that increases airspeed, which normally causes a pilot to reduce engine power if they are unaware of the wind shear. As the aircraft passes into the region of the downdraft, the localized headwind diminishes, reducing the aircraft's airspeed and increasing its sink rate. Then, when the aircraft passes through the other side of the downdraft, the headwind becomes a tailwind, reducing lift generated by the wings, and leaving the aircraft in a low-power, low-speed descent. This can lead to an accident if the aircraft is too low to effect a recovery before ground contact. Between 1964 and 1985, wind shear directly caused or contributed to 26 major civil transport aircraft accidents in the U.S. that led to 620 deaths and 200 injuries.

Engine failure

An engine may fail to function because of fuel starvation (e.g. British Airways Flight 38), fuel exhaustion (e.g. Air Canada Flight 143), foreign object damage (e.g. US Airways Flight 1549), mechanical failure due to metal fatigue (e.g. Kegworth air disaster, El Al Flight 1862, China Airlines Flight 358), mechanical failure due to improper maintenance (e.g. American Airlines Flight 191), mechanical failure caused by an original manufacturing defect in the engine (e.g. Qantas Flight 32, United Airlines Flight 232, Delta Air Lines Flight 1288), and pilot error (e.g. Pinnacle Airlines Flight 3701).

In a multi-engine aircraft, failure of a single engine usually results in a precautionary landing being performed, for example landing at a diversion airport instead of continuing to the intended destination. Failure of a second engine (e.g. US Airways Flight 1549) or damage to other aircraft systems caused by an uncontained engine failure (e.g. United Airlines Flight 232) may, if an emergency landing is not possible, result in the aircraft crashing.

Structural failure of the aircraft

Examples of failure of aircraft structures caused by metal fatigue include the de Havilland Comet accidents (1950s) and Aloha Airlines Flight 243 (1988). Improper repair procedures can also cause structural failures include Japan Airlines Flight 123 (1985) and China Airlines Flight 611 (2002). Now that the subject is better understood, rigorous inspection and nondestructive testing procedures are in place.

Composite materials consist of layers of fibers embedded in a resin matrix. In some cases, especially when subjected to cyclic stress, the layers of the material separate from each other ( delaminate) and lose strength. As the failure develops inside the material, nothing is shown on the surface; instrument methods (often ultrasound-based) have to be used to detect such a material failure. In the 1940s several Yakovlev Yak-9s experienced delamination of plywood in their construction.

Stalling

Stalling an aircraft (increasing the angle of attack to a point at which the wings fail to produce enough lift) is dangerous and can result in a crash if the pilot fails to make a timely correction.

Devices to warn the pilot when the aircraft's speed is decreasing close to the stall speed include stall warning horns (now standard on virtually all powered aircraft), stick shakers, and voice warnings. Most stalls are a result of the pilot allowing the airspeed to be too slow for the particular weight and configuration at the time. Stall speed is higher when ice or frost has attached to the wings and/or tail stabilizer. The more severe the icing, the higher the stall speed, not only because smooth airflow over the wings becomes increasingly more difficult, but also because of the added weight of the accumulated ice.

Crashes caused by a full stall of the airfoils include:
* British European Airways Flight 548 (1972)
* United Airlines Flight 553 (1972)
* Aeroflot Flight 7425 (1985)
* Arrow Air Flight 1285 (1985)
* Northwest Airlines Flight 255 (1987)
* The Paul Wellstone crash (2002)
* Colgan Air Flight 3407 (2009)
* Turkish Airlines Flight 1951 crash (2009)
* Air France Flight 447 (2009)

Fire

Safety regulations control aircraft materials and the requirements for automated fire safety systems. Usually these requirements take the form of required tests. The tests measure flammability of materials and toxicity of smoke. When the tests fail, it is on a prototype in an engineering laboratory rather than in an aircraft.

Fire and its toxic smoke have been the cause of accidents. An electrical fire on Air Canada Flight 797 in 1983 caused the deaths of 23 of the 46 passengers, resulting in the introduction of floor level lighting to assist people to evacuate a smoke-filled aircraft. In 1985, a fire on the runway caused the loss of 55 lives, 48 from the effects of incapacitating and subsequently lethal toxic gas and smoke in the British Airtours Flight 28M accident which raised serious concerns relating to survivability – something that had not been studied in such detail. The swift incursion of the fire into the fuselage and the layout of the aircraft impaired passengers' ability to evacuate, with areas such as the forward galley area becoming a bottle-neck for escaping passengers, with some dying very close to the exits. Much research into evacuation and cabin and seating layouts was carried out at Cranfield Institute to try to measure what makes a good evacuation route, which led to the seat layout by Overwing exits being changed by mandate and the examination of evacuation requirements relating to the design of galley areas. The use of smoke hoods or misting systems were also examined although both were rejected.

South African Airways Flight 295 was lost in the Indian Ocean in 1987 after an in-flight fire in the cargo hold could not be suppressed by the crew. The cargo holds of most airliners are now equipped with automated halon fire extinguishing systems to combat a fire that might occur in the baggage holds. In May 1996, ValuJet Flight 592 crashed into the Florida Everglades a few minutes after takeoff because of a fire in the forward cargo hold. All 110 people on board were killed.

At one time, fire fighting foam paths were laid down before an emergency landing, but the practice was considered only marginally effective, and concerns about the depletion of fire fighting capability due to pre-foaming led the United States FAA to withdraw its recommendation in 1987.

One possible cause of fires in airplanes is wiring problems that involve intermittent faults, such as wires with breached insulation touching each other, having water dripping on them, or short circuits. Notable was Swissair Flight 111 in 1998 due to an arc in the wiring of IFE which ignite flammable MPET insulation. These are difficult to detect once the aircraft is on the ground. However, there are methods, such as spread-spectrum time-domain reflectometry, that can feasibly test live wires on aircraft during flight.

Bird strike

''Bird strike'' is an aviation term for a collision between a bird and an aircraft. Fatal accidents have been caused by both engine failure following bird ingestion and bird strikes breaking cockpit windshields.

Jet engines have to be designed to withstand the ingestion of birds of a specified weight and number and to not lose more than a specified amount of thrust. The weight and numbers of birds that can be ingested without hazarding the safe flight of the aircraft are related to the engine intake area. The hazards of ingesting birds beyond the "designed-for" limit were shown on US Airways Flight 1549 when the aircraft struck Canada geese.

The outcome of an ingestion event and whether it causes an accident, be it on a small fast plane, such as military jet fighters, or a large transport, depends on the number and weight of birds and where they strike the fan blade span or the nose cone. Core damage usually results with impacts near the blade root or on the nose cone.

The highest risk of a bird strike occurs during takeoff and landing in the vicinity of airports, and during low-level flying, for example by military aircraft, crop dusters and helicopters. Some airports use active countermeasures, including a person with a shotgun, playing recorded sounds of predators through loudspeakers, or employing falconers. Poisonous grass can be planted that is not palatable to birds, nor to insects that attract insectivorous birds. Passive countermeasures involve sensible land-use management, avoiding conditions attracting flocks of birds to the area (e.g. landfills). Another tactic found effective is to let the grass at the airfield grow taller (to approximately ) as some species of birds won't land if they cannot see one another.

Human factors

Human factors, including pilot error, are another potential set of factors, and currently the factor most commonly found in aviation accidents. Much progress in applying human factors analysis to improving aviation safety was made around the time of World War II by such pioneers as Paul Fitts and Alphonse Chapanis. However, there has been progress in safety throughout the history of aviation, such as the development of the pilot's checklist in 1937. CRM, or Crew Resource Management, is a technique that makes use of the experience and knowledge of the complete flight crew to avoid dependence on just one crew member, and to improve pilot decision making.

Pilot error and improper communication are often factors in the collision of aircraft. This can take place in the air (1978 Pacific Southwest Airlines Flight 182) ( TCAS) or on the ground (1977 Tenerife disaster) ( RAAS). The barriers to effective communication have internal and external factors. The ability of the flight crew to maintain situation awareness is a critical human factor in air safety. Human factors training is available to general aviation pilots and called single pilot resource management training.

Failure of the pilots to properly monitor the flight instruments caused the crash of Eastern Air Lines Flight 401 in 1972. Controlled flight into terrain (CFIT), and error during take-off and landing can have catastrophic consequences, for example causing the crash of Prinair Flight 191 on landing, also in 1972.

Pilot fatigue

The International Civil Aviation Organization (ICAO) defines fatigue as "A physiological state of reduced mental or physical performance capability resulting from sleep loss or extended wakefulness, circadian phase, or workload." The phenomenon places great risk on the crew and passengers of an airplane because it significantly increases the chance of pilot error. Fatigue is particularly prevalent among pilots because of "unpredictable work hours, long duty periods, circadian disruption, and insufficient sleep". These factors can occur together to produce a combination of sleep deprivation, circadian rhythm effects, and 'time-on task' fatigue. Regulators attempt to mitigate fatigue by limiting the number of hours pilots are allowed to fly over varying periods of time. Experts in aviation fatigue often find that these methods fall short of their goals.

Piloting while intoxicated

Rarely, flight crew members are arrested or subject to disciplinary action for being intoxicated on the job. In 1990, three Northwest Airlines crew members were sentenced to jail for flying while drunk. In 2001, Northwest fired a pilot who failed a breathalyzer test after a flight. In July 2002, both pilots of America West Airlines Flight 556 were arrested just before they were scheduled to fly because they had been drinking alcohol. The pilots were fired and the FAA revoked their pilot licenses. At least one fatal airliner accident involving drunk pilots occurred when Aero Flight 311 crashed at Koivulahti, Finland, killing all 25 on board in 1961.

Pilot suicide and murder

There have been rare instances of suicide by pilots. Although most air crew are screened for psychological fitness, a very few authorized pilots have flown acts of suicide and even mass murder.

In 1982, Japan Airlines Flight 350 crashed while on approach to the Tokyo Haneda Airport, killing 24 of the 174 on board. The official investigation found the mentally ill captain had attempted suicide by placing the inboard engines into reverse thrust, while the aircraft was close to the runway. The first officer did not have enough time to countermand before the aircraft stalled and crashed.

In 1997, SilkAir Flight 185 suddenly went into a high dive from its cruising altitude. The speed of the dive was so high that the aircraft began to break apart before it finally crashed near Palembang, Sumatra. After three years of investigation, the Indonesian authorities declared that the cause of the accident could not be determined. However, the US NTSB concluded that deliberate suicide by the captain was the only reasonable explanation.

In the case of EgyptAir Flight 990, it appears that the first officer deliberately crashed into the Atlantic Ocean while the captain was away from his station in 1999 off Nantucket, Massachusetts.

Crew involvement is one of the speculative theories in the disappearance of Malaysia Airlines Flight 370 on 8 March 2014.

In 2015, on March 24, Germanwings Flight 9525 (an Airbus A320-200) crashed northwest of Nice, in the French Alps, after a constant descent that began one minute after the last routine contact with air traffic control and shortly after the aircraft had reached its assigned cruise altitude. All 144 passengers and six crew members were killed. The crash was intentionally caused by the co-pilot, Andreas Lubitz. Having been declared "unfit to work" without telling his employer, Lubitz reported for duty, and during the flight locked the Captain out of the flightdeck. In response to the incident and the circumstances of Lubitz's involvement, aviation authorities in Canada, New Zealand, Germany and Australia implemented new regulations that require two authorized personnel to be present in the cockpit at all times. Three days after the incident the European Aviation Safety Agency issued a temporary recommendation for airlines to ensure that at least two crew members, including at least one pilot, are in the cockpit at all times of the flight. Several airlines announced they had already adopted similar policies voluntarily.

Deliberate aircrew inaction

Inaction, omission, failure to act as required, willful disregard of safety procedures, disdain for rules, unjustifiable risk-taking by pilots have also led to accidents and incidents.

Although Smartwings QS-1125 flight of 22 August 2019 successfully made an emergency landing at destination, the captain was censured for failing to follow mandatory procedures, including for not landing at the nearest possible diversion airport after an engine failure.

Human factors of third parties

Unsafe human factors are not limited to pilot errors. Third party factors include ground crew mishaps, ground vehicle to aircraft collisions and engineering maintenance related problems. For example, failure to properly close a cargo door on Turkish Airlines Flight 981 in 1974 caused the loss of the aircraft. (However, design of the cargo door latch was also a major factor in the accident.) In the case of Japan Airlines Flight 123 in 1985, improper repair of previous damage led to explosive decompression of the cabin, which in turn destroyed the vertical stabilizer and damaged all four hydraulic systems which powered all the flight controls.

Controlled flight into terrain

''Controlled flight into terrain'' (CFIT) is a class of accidents in which an aircraft is flown under control into terrain or man-made structures. CFIT accidents typically result from pilot error or of navigational system error. Failure to protect ILS critical areas can also cause CFIT accidents. In December 1995, American Airlines Flight 965 tracked off course while approaching Cali, Colombia, and hit a mountainside despite a terrain awareness and warning system (TAWS) terrain warning in the cockpit and desperate pilot attempt to gain altitude after the warning. Crew position awareness and monitoring of navigational systems are essential to the prevention of CFIT accidents. , over 40,000 aircraft had enhanced TAWS installed, and they had flown over 800 million hours without a CFIT accident.

Another anti-CFIT tool is the Minimum Safe Altitude Warning (MSAW) system which monitors the altitudes transmitted by aircraft transponders and compares that with the system's defined minimum safe altitudes for a given area. When the system determines the aircraft is lower, or might soon be lower, than the minimum safe altitude, the air traffic controller receives an acoustic and visual warning and then alerts the pilot that the aircraft is too low.

Electromagnetic interference

The use of certain electronic equipment is partially or entirely prohibited as it might interfere with aircraft operation, such as causing compass deviations. Use of some types of personal electronic devices is prohibited when an aircraft is below , taking off, or landing. Use of a mobile phone is prohibited on most flights because in-flight usage creates problems with ground-based cells.

Ground damage

Various ground support equipment operate in close proximity to the fuselage and wings to service the aircraft and occasionally cause accidental damage in the form of scratches in the paint or small dents in the skin. However, because aircraft structures (including the outer skin) play such a critical role in the safe operation of a flight, all damage is inspected, measured, and possibly tested to ensure that any damage is within safe tolerances.

An example problem was the depressurization incident on Alaska Airlines Flight 536 in 2005. During ground services a baggage handler hit the side of the aircraft with a tug towing a train of baggage carts. This damaged the metal skin of the aircraft. This damage was not reported and the plane departed. Climbing through the damaged section of the skin gave way under the difference in pressure between the inside of the aircraft and the outside air. The cabin depressurized explosively necessitating a rapid descent to denser (breathable) air and an emergency landing. Post-landing examination of the fuselage revealed a hole on the right side of the airplane.

Volcanic ash

Plumes of volcanic ash near active volcanoes can damage propellers, engines and cockpit windows.
In 1982, British Airways Flight 9 flew through an ash cloud and temporarily lost power from all four engines. The plane was badly damaged, with all the leading edges being scratched. The front windscreens had been so badly "sand" blasted by the ash that they could not be used to land the aircraft.

Prior to 2010 the general approach taken by airspace regulators was that if the ash concentration rose above zero, then the airspace was considered unsafe and was consequently closed.
Volcanic Ash Advisory Centers enable liaison between meteorologists, volcanologists, and the aviation industry.

Runway safety

Types of runway safety incidents include:
* Runway excursion – an incident involving only a single aircraft making an inappropriate exit from the runway.
* Runway overrun – a specific type of excursion where the aircraft does not stop before the end of the runway (e.g., Air France Flight 358).
* Runway incursion – incorrect presence of a vehicle, person, or another aircraft on the runway (e.g., Tenerife airport disaster).
* Runway confusion – crew misidentification the runway for landing or take-off (e.g., Comair Flight 191, Singapore Airlines Flight 6).

Terrorism

Aircrew are normally trained to handle hijack situations. Since the September 11, 2001, attacks, stricter airport and airline security measures are in place to prevent terrorism, such as security checkpoints and locking the cockpit doors during flight.

In the United States, the Federal Flight Deck Officer program is run by the Federal Air Marshal Service, with the aim of training active and licensed airline pilots to carry weapons and defend their aircraft against criminal activity and terrorism. Upon completion of government training, selected pilots enter a covert law enforcement and counter-terrorism service. Their jurisdiction is normally limited to a flight deck or a cabin of a commercial airliner or a cargo aircraft they operate while on duty.

Military action

Passenger planes have rarely been attacked in both peacetime and war. Examples:
* In 1955, Bulgaria shot down El Al Flight 402.
* In 1973, Israel shot down Libyan Arab Airlines Flight 114.
* In 1983, the Soviet Union shot down Korean Air Lines Flight 007.
* In 1988, the United States shot down Iran Air Flight 655.
* In 2001, the Ukrainian Air Force accidentally shot down Siberia Airlines Flight 1812 during an exercise.
* In 2014, a rebel from Ukraine- armed with the Russian Aerospace Defense Forces Buk missile system - shot down Malaysia Airlines Flight 17.
* In 2020, Iran shot down Ukraine International Airlines Flight 752.

Accident survivability

Earlier tragedies investigations and improved engineering has allowed many safety improvements that have allowed an increasing safer aviation.

Airport design

Airport design and location can have a large impact on aviation safety, especially since some airports such as Chicago Midway International Airport were originally built for propeller planes and many airports are in congested areas where it is difficult to meet newer safety standards. For instance, the FAA issued rules in 1999 calling for a runway safety area, usually extending to each side and beyond the end of a runway. This is intended to cover ninety percent of the cases of an aircraft leaving the runway by providing a buffer space free of obstacles. Many older airports do not meet this standard. One method of substituting for the at the end of a runway for airports in congested areas is to install an engineered materials arrestor system (EMAS). These systems are usually made of a lightweight, crushable concrete that absorbs the energy of the aircraft to bring it to a rapid stop. , they have stopped three aircraft at JFK Airport.

Emergency airplane evacuations

According to a 2000 report by the National Transportation Safety Board, emergency aircraft evacuations happen about once every 11 days in the U.S. While some situations are extremely dire, such as when the plane is on fire, in many cases the greatest challenge for passengers can be the use of the evacuation slide. In a ''Time'' article on the subject, Amanda Ripley reported that when a new supersized Airbus A380 underwent mandatory evacuation tests in 2006, thirty-three of the 873 evacuating volunteers got hurt. While the evacuation was considered a success, one volunteer suffered a broken leg, while the remaining 32 received slide burns. Such accidents are common. In her article, Ripley provided tips on how to make it down the airplane slide without injury.
Another improvement to airplane evacuations is the requirement by the Federal Aviation Administration for planes to demonstrate an evacuation time of 90 seconds with half the emergency exits blocked for each type of airplane in their fleet. According to studies, 90 seconds is the time needed to evacuate before the plane starts burning, before there can be a very large fire or explosions, or before fumes fill the cabin.

Aircraft materials and design

Changes such as using new materials for seat fabric and insulation has given between 40 and 60 additional seconds to people on board to evacuate before the cabin gets filled with fire and potential deadly fumes. Other improvements through the years include the use of properly rated seatbelts, impact resistant seat frames, and airplane wings and engines designed to shear off to absorb impact forces.

Radar and wind shear detection systems

As the result of the accidents due to wind shear and other weather disturbances, most notably the 1985 crash of Delta Air Lines Flight 191, the U.S. Federal Aviation Administration mandated that all commercial aircraft have on-board wind shear detection systems by 1993. Since 1995, the number of major civil aircraft accidents caused by wind shear has dropped to approximately one every ten years, due to the mandated on-board detection as well as the addition of Doppler weather radar units on the ground (NEXRAD). The installation of high-resolution Terminal Doppler Weather Radar stations at many U.S. airports that are commonly affected by wind shear has further aided the ability of pilots and ground controllers to avoid wind shear conditions.

Accidents and incidents

* List of airship accidents
* Lists of aviation accidents and incidents
* Aviation accidents and incidents
* List of airliner shootdown incidents
* Flight recorder, includes ''flight data recorder'' and ''cockpit voice recorder''

National investigation organizations

* Australian Transport Safety Bureau

Flugunfalluntersuchungsstelle im BMVIT
(Austria)

Centro de Investigação e Prevenção de Acidentes Aeronáuticos
(Brazil)
* Transportation Safety Board of Canada
* Air Accidents Investigation Institute (Czech Republic)

Danish Aircraft Accident Investigation Board
* Bureau d'Enquêtes et d'Analyses pour la sécurité de l'Aviation Civile (France)
* Bundesstelle für Flugunfalluntersuchung (Germany)
* Air Accident Investigation Unit (Ireland)
* Agenzia Nazionale per la Sicurezza del Volo (Italy)
* Aircraft and Railway Accidents Investigation Commission (Japan)
* Civil Aviation Authority of New Zealand
* Transport Accident Investigation Commission (New Zealand)
* Onderzoeksraad voor Veiligheid (The Netherlands)
* Civil Aviation Authority of the Philippines
* Comisión de Investigación de Accidentes e Incidentes de Aviación Civil (Spain)
* Swedish Accident Investigation Board
* Aircraft Accident Investigation Bureau (Switzerland)
* Air Accidents Investigation Branch (UK)
* National Transportation Safety Board (USA)

European Co-ordination Center for Aircraft Incident Reporting Systems
(ECCAIRS)
* International Civil Aviation Organization
* South African Civil Aviation Authority (South Africa)

Aircraft Accident Investigation Bureau
(India)

KNKT - Komite Nasional Keselamatan Transportasi
(Indonesia)

Air safety investigators

Air safety investigators are trained and authorized to investigate aviation accidents and incidents: to research, analyse, and report their conclusions. They may be specialized in flight operations, training, aircraft structures, air traffic control, flight recorders or human factors. They are employed by government organizations responsible for aviation safety, manufacturers or unions, though only government organizations have statutory powers to investigate.

Safety improvement initiatives

The safety improvement initiatives are aviation safety partnerships between regulators, manufacturers, operators, professional unions, research organisations, and international aviation organisations to further enhance safety.
Some major safety initiatives worldwide are:

Commercial Aviation Safety Team (CAST)
in the US. The Commercial Aviation Safety Team (CAST) was founded in 1998 with a goal to reduce the commercial aviation fatality rate in the United States by 80 percent by 2007.

European Strategic Safety Initiative (ESSI)
The European Strategic Safety Initiative (ESSI) is an aviation safety partnership between EASA, other regulators and the industry. The initiative objective is to further enhance safety for citizens in Europe and worldwide through safety analysis, implementation of cost effective action plans, and coordination with other safety initiatives worldwide.
After the disappearance of Malaysia Airlines Flight 370, in June 2014, the International Air Transport Association said it was working on implementing new measures to track aircraft in flight in real time. A special panel was considering a range of options including the production of equipment especially designed to ensure real-time tracking.

Since pilot error accounts for between one-third and 60% of aviation accidents, advances in automation and technology could replace some or all of the duties of the aircraft pilots. Automation since the 1980s has already eliminated the need for flight engineers. In complex situations with severely degraded systems, the problem-solving and judgement capability of humans is challenging to achieve with automated systems, for example the catastrophic engine failures experienced by United Airlines Flight 232 and Qantas Flight 32. However, with more accurate software modeling of aeronautic factors, test planes have been successfully flown in these conditions.

While the accident rate is very low, to ensure they do not rise with the air transport growth, experts recommend creating a robust culture of collecting information from employees without blame.

Regulation

*Directorate- General of Civil Aviation, India.
* Civil Aviation Authority (United Kingdom)
* Department of Infrastructure, Transport, Regional Development and Local Government (Australia)
* European Aviation Safety Agency
* Federal Aviation Administration (United States)
** Federal Aviation Regulations
* Irish Aviation Authority
* Transport Canada
* Directorate General of Civil Aviation (Indonesia)

See also

* Aircraft fire trainer
* Aircraft hijacking
* Airport security
* Aviation Safety Network
* Aviation Safety Reporting System
* Ballistic parachute
* Crashworthiness
* Chicago Convention on International Civil Aviation
* Hazard analysis
* Health hazards of air travel
* IATA Operational Safety Audit
* Jet Airliner Crash Data Evaluation Centre
* Lasers and aviation safety
* Mid-air collision
* Pilot error
* Safety of emergency medical services flights
* Sensory illusions in aviation
* Sixty second review
* Swiss cheese model
* System accident
* Tombstone mentality
*
* Uncontrolled decompression
* Wind shear
* Zonal safety analysis

Notes

References

External links

10 Plane Crashes That Changed Aviation
*

Safety Behaviours, a guide for pilots (comprehensive human factors information)

NASA Aviation Safety Reporting System (ASRS)

Latest Aviation Safety Occurrences at the Aviation Safety Network

Aviation Safety: Advancements Being Pursued to Improve Airliner Cabin Occupant Safety and Health, 2003

{{DEFAULTSORT:Aviation Safety

Safety