|
ESP8266
The ESP8266 is a low-cost Wi-Fi microchip, with built-in TCP/IP stack, TCP/IP networking software, and microcontroller capability, produced by Espressif Systems in Shanghai, China. The chip was popularized in the English-speaking maker culture, maker community in August 2014 via the ESP-01 module, made by a third-party manufacturer Ai-Thinker. This small module allows microcontrollers to connect to a Wi-Fi network and make simple TCP/IP connections using Hayes command set, Hayes-style commands. However, at first, there was almost no English-language documentation on the chip and the commands it accepted. The very low price and the fact that there were very few external components on the module, which suggested that it could eventually be very inexpensive in volume, attracted many hackers to explore the module, the chip, and the software on it, as well as to translate the Chinese documentation. The ESP8285 is a similar chip with a built-in 1 MiB flash memory, allowing the d ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
ESP32
ESP32 is a series of low-cost, low-power system on a chip microcontrollers with integrated Wi-Fi and dual-mode Bluetooth. The ESP32 series employs either a Tensilica Xtensa LX6 microprocessor in both dual-core and single-core variations, Xtensa LX7 dual-core microprocessor or a single-core RISC-V microprocessor and includes built-in antenna switches, Radio frequency, RF balun, power amplifier, low-noise receive amplifier, filters, and power-management modules. ESP32 is created and developed by Espressif Systems, a Shanghai-based Chinese company, and is manufactured by TSMC using their 40 nm process. It is a successor to the ESP8266 microcontroller. Features Features of the ESP32 include the following: * Processors: ** CPU: Xtensa dual-core (or single-core) 32-bit LX6 microprocessor, operating at 160 or 240 MHz and performing at up to 600 Dhrystone, DMIPS ** Ultra low power (ULP) co-processor * Memory: 320 KiB RAM, 448 KiB ROM * Wireless connectivity: ** Wi-Fi: IEEE 8 ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Tensilica
Tensilica was a company based in Silicon Valley in the semiconductor intellectual property core business. It is now a part of Cadence Design Systems. Tensilica is known for its customizable Xtensa microprocessor core. Other products include: HiFi audio/voice DSPs (digital signal processors) with a software library of over 225 codecs from Cadence and over 100 software partners; Vision DSPs that handle complex algorithms in imaging, video, computer vision, and neural networks; and the ConnX family of baseband DSPs ranging from the dual- MAC ConnX D2 to the 64-MAC ConnX BBE64EP. Tensilica was founded in 1997 by Chris Rowen (one of the founders of MIPS Technologies). It employed Earl Killian, who contributed to the MIPS architecture, as director of architecture. On March 11, 2013, Cadence Design Systems announced its intent to buy Tensilica for approximately $380 million in cash. Cadence completed the acquisition in April 2013, with a cash outlay at closing of approximately $326 mill ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
RF Power Amplifier
A radio-frequency power amplifier (RF power amplifier) is a type of electronic amplifier that converts a low-power radio-frequency signal (electrical engineering), signal into a higher-power signal. Typically, RF power amplifiers drive the antenna of a transmitter. Design goals often include gain (electronics), gain, power output, bandwidth, power efficiency, linearity (low Gain compression, signal compression at rated output), input and output impedance matching, and heat dissipation. Amplifier classes Many modern RF amplifiers operate in different modes, called "classes", to help achieve different design goals. Some classes are Class-A amplifier, class A, Class-AB amplifier, class AB, electronic amplifier#Class B and AB, class B, electronic amplifier#Class C, class C, which are considered the linear amplifier classes. In these classes the active device is used as a controlled current source. The bias at the input determines the class of the amplifier. A com ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Pinout
In electronics, a pinout (sometimes written "pin-out") is a cross-reference between the contacts, or ''pins'', of an electrical connector or electronic component, and their functions. "Pinout" now supersedes the term "basing diagram" that was the standard terminology used by the manufacturers of vacuum tubes and the RMA. The RMA started its standardization in 1934, collecting and correlating tube data for registration at what was to become the EIA. The EIA (Electronic Industries Alliance) now has many sectors reporting to it, and sets what are known as EIA standards where all registered pinouts and registered jacks can be found. Purpose The functions of contacts in electrical connectors, be they power- or signaling-related, must be specified in order for connectors to be interchangeable. When connected, each contact of a connector must mate with the contact on the other connector that has the same function. If contacts of disparate functions are allowed to make contact, the conne ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Successive Approximation ADC
A successive-approximation ADC is a type of analog-to-digital converter that converts a continuous analog waveform into a discrete digital representation using a binary search through all possible quantization levels before finally converging upon a digital output for each conversion. Algorithm The successive-approximation analog-to-digital converter circuit typically consists of four chief subcircuits: # A sample-and-hold circuit to acquire the input voltage . # An analog voltage comparator that compares to the output of the internal DAC and outputs the result of the comparison to the successive-approximation register (SAR). # A successive-approximation register subcircuit designed to supply an approximate digital code of to the internal DAC. # An internal reference DAC that, for comparison with , supplies the comparator with an analog voltage equal to the digital code output of the . The successive approximation register is initialized so that the most significant b ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Analog-to-digital Converter
In electronics, an analog-to-digital converter (ADC, A/D, or A-to-D) is a system that converts an analog signal, such as a sound picked up by a microphone or light entering a digital camera, into a digital signal. An ADC may also provide an isolated measurement such as an electronic device that converts an analog input voltage or current to a digital number representing the magnitude of the voltage or current. Typically the digital output is a two's complement binary number that is proportional to the input, but there are other possibilities. There are several ADC architectures. Due to the complexity and the need for precisely matched components, all but the most specialized ADCs are implemented as integrated circuits (ICs). These typically take the form of metal–oxide–semiconductor (MOS) mixed-signal integrated circuit chips that integrate both analog and digital circuits. A digital-to-analog converter (DAC) performs the reverse function; it converts a digital signa ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Universal Asynchronous Receiver/transmitter
A universal asynchronous receiver-transmitter (UART ) is a computer hardware device for asynchronous serial communication in which the data format and transmission speeds are configurable. It sends data bits one by one, from the least significant to the most significant, framed by start and stop bits so that precise timing is handled by the communication channel. The electric signaling levels are handled by a driver circuit external to the UART. Two common signal levels are RS-232, a 12-volt system, and RS-485, a 5-volt system. Early teletypewriters used current loops. It was one of the earliest computer communication devices, used to attach teletypewriters for an operator console. It was also an early hardware system for the Internet. A UART is usually an individual (or part of an) integrated circuit (IC) used for serial communications over a computer or peripheral device serial port. One or more UART peripherals are commonly integrated in microcontroller chips. Specialised ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
I²S
I²S (Inter-IC Sound, pronounced "eye-squared-ess"), is an electrical serial bus interface standard used for connecting digital audio devices together. It is used to communicate PCM audio data between integrated circuits in an electronic device. The I²S bus separates clock and serial data signals, resulting in simpler receivers than those required for asynchronous communications systems that need to recover the clock from the data stream. Alternatively I²S is spelled I2S (pronounced eye-two-ess) or IIS (pronounced eye-eye-ess). Despite the similar name, I²S is unrelated to the bidirectional I²C (IIC) bus. History This standard was introduced in 1986 by Philips Semiconductor (now NXP Semiconductors) and was first revised June 5, 1996. The standard was last revised on February 17, 2022 and updated terms ''master'' and ''slave'' to ''controller'' and ''target''. Details The I²S protocol outlines one specific type of PCM digital audio communication with defined paramete ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
I²C
I2C (Inter-Integrated Circuit, ), alternatively known as I2C or IIC, is a synchronous, multi-controller/multi-target (master/slave), packet switched, single-ended, serial communication bus invented in 1982 by Philips Semiconductors. It is widely used for attaching lower-speed peripheral ICs to processors and microcontrollers in short-distance, intra-board communication. Several competitors, such as Siemens, NEC, Texas Instruments, STMicroelectronics, Motorola, Nordic Semiconductor and Intersil, have introduced compatible I2C products to the market since the mid-1990s. System Management Bus (SMBus), defined by Intel in 1995, is a subset of I2C, defining a stricter usage. One purpose of SMBus is to promote robustness and interoperability. Accordingly, modern I2C systems incorporate some policies and rules from SMBus, sometimes supporting both I2C and SMBus, requiring only minimal reconfiguration either by commanding or output pin use. Applications I2C is appropriate for peri ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Serial Peripheral Interface Bus
The Serial Peripheral Interface (SPI) is a synchronous serial communication interface specification used for short-distance communication, primarily in embedded systems. The interface was developed by Motorola in the mid-1980s and has become a ''de facto'' standard. Typical applications include Secure Digital cards and liquid crystal displays. SPI devices communicate in full duplex mode using a master-slave architecture usually with a single master (though some Atmel and Silabs devices support changing roles on the fly depending on an external (SS) pin). The master (controller) device originates the frame for reading and writing. Multiple slave-devices may be supported through selection with individual chip select (CS), sometimes called slave select (SS) lines. Sometimes SPI is called a ''four-wire'' serial bus, contrasting with three-, two-, and one-wire serial buses. The SPI may be accurately described as a synchronous serial interface, but it is different from the Sy ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
.jpg "Click for more on -> RF Power Amplifier")
.jpg "Click for more on -> I²C")
