Wacker process

The Wacker process or the Hoechst-Wacker process (named after the chemical companies of the same name) is an industrial chemical reaction: the aerobic oxidation of ethylene to acetaldehyde in the presence of catalytic, aqueous palladium(II) chloride and copper(II) chloride.
:
The Tsuji-Wacker oxidation refers to a family of reactions inspired by the Wacker process. In Tsuji-Wacker reactions, palladium(II) catalyzes transformation of α-olefins into carbonyl compounds in various solvents.
:
The development of the Wacker process popularized modern organopalladium chemistry, and Tsuji-Wacker oxidations remain in use today.

History

The Wacker process was one of the first homogeneous catalysis with organopalladium chemistry applied on an industrial scale.

In an 1893 doctoral dissertation on Pennsylvanian natural gas, Francis Clifford Phillips had reported that palladium(II) chloride oxidized ethylene to acetaldehyde, but the reaction required stoichiometric quantities of palladium. It remained a niche curiosity until Wacker Chemie began developing its eponymous process in 1956.''Acetaldehyde from Ethylene — A Retrospective on the Discovery of the Wacker Process'' Reinhard Jira Angew. Chem. Int. Ed. 2009, ''48'', 9034–9037

At the time, many industrial compounds were produced via acetaldehyde from acetylene, itself from calcium carbide. The overall route exhibited poor thermodynamic efficiency and required great expense. Esso sought to market waste olefins from a new, under-construction oil refinery in Cologne close to a Wacker site. Wacker realized that ethylene would be a cheaper feedstock than acetylene, and began to investigate catalytic oxidation to ethylene oxide.

To Wacker's surprise, they smelled not ethylene oxide but acetaldehyde in the product stream. From Phillips' dissertation, known properties of Zeise's salt, and transformation of the catalyst over the course of a batch reaction, Wacker realized that they needed to reoxidize the palladium to close the catalytic cycle. They began publishing the process outline in 1957. However, poor patenting strategy allowed parent corporation Hoechst AG to outrace Wacker to the optimal catalysis conditions.

Wacker-Hoechst began jointly constructing pilot plants in 1958, but the relatively aggressive reaction conditions required the first large-scale use of titanium metal in the European chemical industry to protect against corrosion. Production plants started operation in 1960.

The process also sparked a boom in organopalladium chemistry. Studies from the 1960s elucidated several key points about the reaction mechanism through kinetic isotope effects (or lack thereof) and stereochemistry.Henry, Patrick M. In Handbook of Organopalladium Chemistry for Organic Synthesis; Negishi, E., Ed.; Wiley & Sons: New York, 2002; p 2119. Many focused on the hydroxypalladation step, which forms the C–O bond. Early reactions used conditions much milder than the industrial plants and obtained contradictory results; the modern consensus is that the step's stereochemistry is quite sensitive to chloride concentrations.

Other studies investigated reaction's application to more complex terminal olefins. High-order olefins are insoluble in water, but Clement and Selwitz found that aqueous DMF as solvent allowed for the oxidation of 1-dodecene to 2-dodecanone. Fahey noted the use of 3-methylsulfolane in place of DMF as solvent increased the yield of oxidation of 3,3-Dimethylbut-1-ene. Two years after, Tsuji applied the Clement-Selwitz conditions for selective oxidations of terminal olefins with multiple functional groups, and demonstrated its utility in synthesis of complex substrates.

Carbonylation has mainly superseded the Wacker process for modern bulk chemical synthesis, but small-scale Tsuji-Wacker reactions remain important for fine chemical and laboratory-scale syntheses.

Reaction mechanism

The reaction mechanism for the industrial Wacker process (olefin oxidation via palladium(II) chloride) has received significant attention for several decades. Aspects of the mechanism are still debated. A modern formulation is described below:

This reaction can also be described as follows:
: dCl₄sup>2 − + C₂H₄ + H₂O → CH₃CHO + Pd + 2 HCl + 2 Cl⁻,
followed by reactions that regenerate the Pd(II) catalyst:
: Pd + 2 CuCl₂ + 2 Cl ⁻ → dCl₄sup>2− + 2 CuCl
: 2 CuCl + O₂ + 2 HCl → 2 CuCl₂ + H₂O

Only the alkene and oxygen are consumed. Without copper(II) chloride as an oxidizing agent, Pd(0) metal (resulting from beta-hydride elimination of Pd(II) in the final step) would precipitate, stopping Philips' reaction after one cycle. Air, pure oxygen, or a number of other reagents can then oxidise the resultant CuCl-chloride mixture back to CuCl₂, allowing the cycle to continue.

High concentrations of chloride and copper(II) chloride favor formation of a new product, ethylene chlorohydrin.

Evidence

Evidence for the overall mechanism includes:

*No H/D exchange effects. Experiments with C₂D₄ in water generate CD₃CDO, and runs with C₂H₄ in D₂O generate CH₃CHO. Thus, keto-enol tautomerization is not a possible mechanistic step.
* Negligible kinetic isotope effect with fully deuterated reactants (=1.07). Hence hydride transfer is not rate-determining.
* Significant competitive isotope effect with C₂H₂D₂, (= ~1.9), suggests that the rate determining step precedes acetaldehyde formation.
Evidence against the mechanism is a copper-chloride containing byproduct crystallized by Hosokawa ''et al''. Questions remain about whether the cocatalyst also helps hydroxylate the ethylene ligand.

The ethylene ligand's hydroxylation is typically a slow process.Zaw, K., Lautens, M. and Henry P.M. ''Organometallics'', 1985, ''4'', 1286–1296Wan W.K., Zaw K., and Henry P.M. ''Organometallics'', 1988, ''7'', 1677–1683 Depending on experimental conditions, it can occur either intramolecularly, from a palladium-bound hydroxido ligand, or intermolecularly. In the former case the hydroxylation is ''anti''; in the latter, ''syn''. Assuming small amounts of copper, experiments have shown that ''syn'' addition occurs at low chloride concentrations (< 1 mol/ L, industrial process conditions) and ''anti'' addition occurs at high (> 3mol/L) concentrations. The pathway change is probably due to chloride ions saturating the catalyst.Francis, J.W., Henry, P.M. ''Organometallics'', 1991, ''10'', 3498. Francis, J.W., Henry, P.M. ''Organometallics'', 1992, ''11'', 2832. However, under strictly copper-free conditions, ''anti'' addition always occurs, and the rate no longer depends on the ethylene hydrogen isotopes.

Another key step in the Wacker process is the migration of the hydrogen from oxygen to chloride, followed by reductive elimination to form the C-O double bond. This step is generally thought to proceed through a so-called β-hydride elimination:

The cyclic four-membered transition state shown above is unlikely. ''In silico'' studies argue that the transition state for this reaction step likely involves a 7-membered ring with a (solvent) water molecule acting as a catalyst.

Industrial process

Two routes are commercialized for the production of acetaldehyde: one-stage process and two-stage. The acetaldehyde yield is about 95% in either, and byproducts are chlorinated hydrocarbons, chlorinated acetaldehydes, and acetic acid. In general, 100 parts of ethene gives:

* 95 parts acetaldehyde
* 1.9 parts chlorinated aldehydes
* 1.1 parts unconverted ethene
* 0.8 parts carbon dioxide
* 0.7 parts acetic acid
* 0.1 parts chloromethane
* 0.1 parts ethyl chloride
* 0.3 parts ethane, methane, crotonaldehyde

and other minor side products.

The production costs are virtually the same across the two processes; the advantage of using dilute gases in the two-stage method is balanced by higher investment costs. Due to the corrosive nature of the catalyst, either process requires a reactor lined with acid-proof ceramic and titanium tubing, but the two-stage process requires more reactors and piping. Generally, the choice of method is governed by the raw material and energy situations as well as by the availability of oxygen at a reasonable price.

One-stage process

Ethene and oxygen are passed co-currently in a reaction tower at about 130 °C and 400 kPa. The catalyst is an aqueous solution of PdCl₂ and CuCl₂. The acetaldehyde is purified by extractive distillation followed by fractional distillation. Extractive distillation with water removes the lights ends having lower boiling points than acetaldehyde (chloromethane, chloroethane, and carbon dioxide) at the top, while water and higher-boiling byproducts, such as acetic acid, crotonaldehyde or chlorinated acetaldehydes, are withdrawn together with acetaldehyde at the bottom.

Two-stage process

In two-stage process, reaction and oxidation are carried out separately in tubular reactors. Unlike one-stage process, air can be used instead of oxygen. Ethylene is passed through the reactor along with catalyst at 105–110 °C and 900–1000 kPa. Catalyst solution containing acetaldehyde is separated by flash distillation. The catalyst is oxidized in the oxidation reactor at 1000 kPa using air as oxidizing medium. Oxidized catalyst solution is separated and sent back to reactor. Oxygen from air is used up completely and the exhaust air is circulated as inert gas. Acetaldehyde – water vapor mixture is preconcentrated to 60–90% acetaldehyde by utilizing the heat of reaction and the discharged water is returned to the flash tower to maintain catalyst concentration. A two-stage distillation of the crude acetaldehyde follows. In the first stage, low-boiling substances, such as chloromethane, chloroethane and carbon dioxide, are separated. In the second stage, water and higher-boiling by-products, such as chlorinated acetaldehydes and acetic acid, are removed and acetaldehyde is obtained in pure form overhead.

Tsuji-Wacker oxidation

Development of the reaction system has led to various catalytic systems to address selectivity of the reaction, as well as introduction of intermolecular and intramolecular oxidations with non-water nucleophiles.

Regioselectivity

Markovnikov addition

The oxidation of terminal olefins generally provide the Markovnikov ketone product. In rare cases where substrate favors the aldehyde (discussed below), different ligands can be used to enforce Markovnikov regioselectivity. Sparteine (Figure 2, A) favors nucleopalladation at the terminal carbon to minimize steric interaction between the palladium complex and substrate. Quinox (Figure 2, B) favors ketone formation when the substrate contains a directing group. When such substrate bind to Pd(Quinox)(OOtBu), this complex is coordinately saturated which prevents the binding of the directing group, and results in formation of the Markovnikov product. The efficiency of this ligand is also attributed to its electronic property, where anionic TBHP prefers to bind ''trans'' to the oxazoline and olefin coordinate ''trans'' to the quinoline.

Anti-Markovnikov addition 

The anti-Markovnikov addition selectivity to aldehyde can be achieved through exploiting inherent stereoelectronics of the substrate. Placement of directing group at homo-allylic (i.e. Figure 3, A) and allylic position (i.e. Figure 3, B) to the terminal olefin favors the anti-Markovnikov aldehyde product, which suggests that in the catalytic cycle the directing group chelates to the palladium complex such that water attacks at the anti-Markovnikov carbon to generate the more thermodynamically stable palladacycle. Anti-Markovnikov selectivity is also observed in styrenyl substrates (i.e. Figure 3, C), presumably via η⁴-palladium-styrene complex after water attacks anti-Markovnikov. More examples of substrate-controlled, anti-Markovnikov Tsuji-Wacker Oxidation of olefins are given in reviews by Namboothiri, Feringa, and Muzart.

Grubbs and co-workers paved way for anti-Markovnikov oxidation of stereoelectronically unbiased terminal olefins, through the use of palladium-nitrite system (Figure 2, D). In his system, the terminal olefin was oxidized to the aldehyde with high selectivity through a catalyst-control pathway. The mechanism is under investigation, however evidence suggests it goes through a nitrite radical adds into the terminal carbon to generate the more thermodynamically stable, secondary radical. Grubbs expanded this methodology to more complex, unbiased olefins.

Scope

Oxygen nucleophiles 

The intermolecular oxidations of olefins with alcohols as nucleophile typically generate ketals, where as the palladium-catalyzed oxidations of olefins with carboxylic acids as nucleophile generates vinylic or allylic carboxylates. In case of diols, their reactions with alkenes typically generate ketals, whereas reactions of olefins bearing electron-withdrawing groups tend to form acetals.

Palladium-catalyzed intermolecular oxidations of dienes with carboxylic acids and alcohols as donors give 1,4-addition products. In the case of cyclohexadiene (Figure 4, A), Backvall found that stereochemical outcome of product was found to depend on concentration of LiCl. This reaction proceeds by first generating the Pd(OAc)(benzoquinone)(allyl) complex, through anti-nucleopalladation of diene with acetate as nucleophile. The absence of LiCl induces an inner sphere reductive elimination to afford the trans-acetate stereochemistry to give the trans-1,4-adduct. The presence of LiCl displaces acetate with chloride due to its higher binding affinity, which forces an outer sphere acetate attack anti to the palladium, and affords the cis-acetate stereochemistry to give the cis-1,4-adduct. Intramolecular oxidative cyclization: 2-(2-cyclohexenyl)phenol cyclizes to corresponding dihydro-benzofuran (Figure 4, B); 1-cyclohexadiene-acetic acid in presence of acetic acid cyclizes to corresponding lactone-acetate 1,4 adduct (Figure 4, C), with cis and trans selectivity controlled by LiCl presence.

Nitrogen nucleophiles

The oxidative aminations of olefins are generally conducted with amides or imides; amines are thought to be protonated by the acidic medium or to bind the metal center too tightly to allow for the catalytic chemistry to occur. These nitrogen nucleophiles are found to be competent in both intermolecular and intramolecular reactions, some examples are depicted (Figure 5, A, B)

Notes

References

{{Authority control

Organic redox reactions
Organometallic chemistry
Homogeneous catalysis
Acetylene
Ethylene
Palladium
Name reactions