|
Flat-four Engine
A flat-four engine, also known as a horizontally opposed-four engine or boxer engine, is a four-cylinder piston engine with two banks of cylinders lying on opposite sides of a common crankshaft. The most common type of flat-four engine is the boxer-four engine, each pair of opposed pistons moves inwards and outwards at the same time. A boxer-four engine has perfect primary and secondary balance, however, the two cylinder heads means the design is more expensive to produce than a straight-four engine. There is a minor, secondary unbalanced rotational torque pulse in the plane of the pistons, when a piston pair at one end of the engine is at TDC and the other pair at BDC. The TDC pair creates a torque greater than the BDC pair, so the net unbalanced torque pulse is the difference. The difference in TDC vs BDC inertial forces is explained in the Engine balance section. Boxer-four engines have been used in cars since 1897, especially by Volkswagen and Subaru. They have also occasional ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Liquid Cooling
Liquid cooling refers to cooling by means of the convection or circulation (fluid dynamics), circulation of a liquid. Examples of liquid cooling technologies include: * Cooling by convection or circulation of coolant, including water cooling * Liquid cooling and ventilation garments, worn by astronauts * Liquid metal cooled reactors * Radiator (engine cooling), Radiators (engine cooling) * Cooling towers Applications Computing In computing and electronics, liquid cooling involves the technology that uses a special water block to conduct heat away from the processor as well as the chipset. This method can also be used in combination with other traditional cooling methods such as those that use air. The application to microelectronics is either indirect or direct. The former pertains to the category that utilizes cold plate cooling, which uses water as coolant while, in the latter (also referred to as liquid immersion cooling), the surface of the chips comes in contact with the ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Wilson-Pilcher
Wilson-Pilcher was an English car company founded in 1901 and acquired by Sir WG Taken Armstrong Whitworth & Co., Limited in 1904. History The company ''Wilson-Pilcher'' was founded in 1901 by Walter Gordon Wilson in London to produce automobiles. In 1904 it was acquired by Sir WG Taken Armstrong Whitworth & Co., Limited and production moved to Newcastle upon Tyne. Percy Pilcher had died in a gliding accident in 1899, and Wilson had been working with him on the engine for an attempt at powered flight. According to Bonhams there is photographic evidence of a wooden mock-up of the car in 1899, and a photo of a working car taken at Stanhope Hall in 1900. Production stopped in 1907. Vehicles The first model had a 9 hp four cylinder flat engine of 2400 cc displacement. In 1903 this was replaced by the 12/16 hp engine of 2694 cc capacity. In 1904 a six-cylinder 18/24 HP engine of 4041 cc capacity was added to the range. In April 1904 The ''Automotor Journal'' gave a ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Karl Benz
Carl (or Karl) Friedrich Benz (; born Karl Friedrich Michael Vaillant; 25 November 1844 – 4 April 1929) was a German engine designer and automotive engineer. His Benz Patent-Motorwagen from 1885 is considered the first practical modern automobile and first car put into series production. He received a patent for the motorcar in 1886, the same year he first publicly drove the Benz Patent-Motorwagen. His company Benz & Cie., based in Mannheim, was the world's first automobile plant and largest of its day. In 1926, it merged with Daimler Motoren Gesellschaft to form Daimler-Benz, which produces the Mercedes-Benz among other brands. Benz is widely regarded as "the father of the car", as well as the "father of the automobile industry". Early life Carl Benz was born Karl Friedrich Michael Vaillant on 25 November 1844 in Mühlburg, now a borough of Karlsruhe, Baden-Württemberg, which is part of modern Germany. His parents were Josephine Vaillant and a locomotive driver, Joh ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Wilson-Pilcher Flat-4 Engine
Wilson-Pilcher was an English car company founded in 1901 and acquired by Sir WG Taken Armstrong Whitworth & Co., Limited in 1904. History The company ''Wilson-Pilcher'' was founded in 1901 by Walter Gordon Wilson in London to produce automobiles. In 1904 it was acquired by Sir WG Taken Armstrong Whitworth & Co., Limited and production moved to Newcastle upon Tyne. Percy Pilcher had died in a gliding accident in 1899, and Wilson had been working with him on the engine for an attempt at powered flight. According to Bonhams there is photographic evidence of a wooden mock-up of the car in 1899, and a photo of a working car taken at Stanhope Hall in 1900. Production stopped in 1907. Vehicles The first model had a 9 hp four cylinder flat engine of 2400 cc displacement. In 1903 this was replaced by the 12/16 hp engine of 2694 cc capacity. In 1904 a six-cylinder 18/24 HP engine of 4041 cc capacity was added to the range. In April 1904 The ''Automotor Journal'' gave a ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Exhaust Manifold
In automotive engineering, an exhaust manifold collects the exhaust gases from multiple cylinders into one pipe. The word ''manifold'' comes from the Old English word ''manigfeald'' (from the Anglo-Saxon ''manig'' anyand ''feald'' old and refers to the folding together of multiple inputs and outputs (in contrast, an inlet or intake manifold ''supplies'' air ''to'' the cylinders). Exhaust manifolds are generally simple cast iron or stainless steel units which collect engine exhaust gas from multiple cylinders and deliver it to the exhaust pipe. For many engines, there are aftermarket tubular exhaust manifolds known as headers in American English, as extractor manifolds in British and Australian English, and simply as "tubular manifolds" in British English. These consist of individual exhaust headpipes for each cylinder, which then usually converge into one tube called a collector. Headers that do not have collectors are called zoomie headers. The most common types of afterm ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Firing Order
The firing order of an internal combustion engine is the sequence of ignition for the cylinders. In a spark ignition (e.g. gasoline/petrol) engine, the firing order corresponds to the order in which the spark plugs are operated. In a diesel engine, the firing order corresponds to the order in which fuel is injected into each cylinder. Four-stroke engines must also time the valve openings relative to the firing order, as the valves do not open and close on every stroke. Firing order affects the vibration, sound and evenness of power output from the engine and heavily influences crankshaft design. Cylinder numbering Numbering systems for car engines The numbering system for cylinders is generally based on the cylinder numbers increasing from the front to the rear of an engine (See engine orientation below). However, there are differences between manufacturers in how this is applied; some commonly used systems are as listed below. Straight engine In a straight engine the cylin ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Harmonic Damper
A harmonic damper is a device fitted to the free (accessory drive) end of the crankshaft of an internal combustion engine to counter Torsional vibration, torsional and resonance vibrations from the crankshaft. This device must be an interference fit to the crankshaft in order to operate in an effective manner. An interference fit ensures the device moves in perfect step with the crankshaft. It is essential on engines with long crankshafts (such as straight-six or straight-eight engines) and V8 engines with cross plane cranks, or V6 and straight-three engine, straight-three engines with uneven firing order. Harmonics and torsional vibrations can greatly reduce crankshaft life, or cause instantaneous failure if the crankshaft runs at or through an amplified resonance. Dampers are designed with a specific weight (mass) and diameter, which are dependent on the damping material/method used, to reduce mechanical Q factor, or damp, crankshaft resonances. A harmonic balancer (sometimes ca ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Flywheel
A flywheel is a mechanical device that uses the conservation of angular momentum to store rotational energy, a form of kinetic energy proportional to the product of its moment of inertia and the square of its rotational speed. In particular, assuming the flywheel's moment of inertia is constant (i.e., a flywheel with fixed mass and second moment of area revolving about some fixed axis) then the stored (rotational) energy is directly associated with the square of its rotational speed. Since a flywheel serves to store mechanical energy for later use, it is natural to consider it as a kinetic energy analogue of an electrical Inductor. Once suitably abstracted, this shared principle of energy storage is described in the generalized concept of an accumulator. As with other types of accumulators, a flywheel inherently smooths sufficiently small deviations in the power output of a system, thereby effectively playing the role of a low-pass filter with respect to the mechanical veloc ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Power Stroke (engine)
In the context of an internal combustion engine, the term stroke has the following related meanings: * A phase of the engine's cycle (e.g. compression stroke, exhaust stroke), during which the piston travels from top to bottom or vice versa. * The type of power cycle used by a piston engine (e.g. two-stroke engine, four-stroke engine). * "Stroke length", the distance travelled by the piston during each cycle. The stroke length, along with bore (engine), bore diameter, determines the engine's engine displacement, displacement. Phases in the power cycle Commonly used engine phases or strokes (i.e. those used in a four-stroke engine) are described below. Other types of engines can have very different phases. Induction-intake stroke The induction stroke is the first phase in a four-stroke (e.g. Otto cycle or Diesel cycle) engine. It involves the downward movement of the piston, creating a partial vacuum that draws an air-fuel mixture (or air alone, in the case of a direct injec ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Couple (mechanics)
In physics, a couple or torque is a pair of forces that are equal in magnitude but opposite in their direction of action. A couple produce a pure Rotation, rotational motion without any Translation, translational form. Simple couple The simplest kind of couple consists of two equal and opposite forces whose line of action, lines of action do not coincide. This is called a "simple couple".''Dynamics, Theory and Applications'' by T.R. Kane and D.A. Levinson, 1985, pp. 90–99Free download/ref> The forces have a turning effect or moment called a torque about an axis which is normal (geometry), normal (perpendicular) to the plane of the forces. The SI unit for the torque of the couple is newton metre. If the two forces are and , then the Euclidean vector, magnitude of the torque is given by the following formula: \tau = F d where *\tau is the moment of couple * is the magnitude of the force * is the perpendicular distance (moment) between the two parallel forces The magnitude of ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Crankpin
A crankpin or crank pin, also known as a rod bearing journal, is a mechanical device in an engine which connects the crankshaft to the connecting rod for each cylinder. It has a cylindrical surface, to allow the crankpin to rotate relative to the "big end" of the connecting rod. The most common configuration is for a crankpin to serve one cylinder. However, many V engines have each crankpin shared by each pair of cylinders. Design The crankpin connects to the larger end of the connecting rod for each cylinder. This end of the connecting rod is called the "big end", as opposed to the "small end" or "little end" (which connects to the wrist/gudgeon pin in the piston). The bearing which allows the crankpin to rotate around its shaft is called the "rod bearing". In automotive engines, the most common type of rod bearing is the plain bearing, however bushings or roller bearings are also used in some engines. Configurations In a single-cylinder engine, straight engine or fla ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
