|
Digital Potentiometer
A digital potentiometer (also called a resistive digital-to-analog converter, or informally a digipot) is a digitally-controlled electronic component that mimics the analog functions of a potentiometer. It is often used for trimming and scaling analog signals by microcontrollers. Design A digital potentiometer is built either from a resistor ladder integrated circuit or a digital-to-analog converter although a resistor ladder construction is the more common. Every step on the resistor ladder has its own switch which can connect this step to the output terminal of the potentiometer. The selected step on the ladder determines the resistance ratio of the digital potentiometer. The number of steps is normally indicated with a bit value e.g. 8 bits equals 256 steps; 8 bits is the most common, but resolutions between 5 and 10 bits (32 to 1024 steps) are available. A digital potentiometer uses protocols like I²C or a Serial Peripheral Interface bus for signalling; some use simpler up/do ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Digital Potentiometer Schematic Symbol Example
Digital usually refers to something using discrete digits, often binary digits. Businesses *Digital bank, a form of financial institution *Digital Equipment Corporation (DEC) or Digital, a computer company *Digital Research (DR or DRI), a software company Computing and technology Hardware *Digital electronics, electronic circuits which operate using digital signals **Digital camera, which captures and stores digital images ***Digital versus film photography **Digital computer, a computer that handles information represented by discrete values **Digital recording, information recorded using a digital signal Socioeconomic phenomena *Digital culture, the anthropological dimension of the digital social changes *Digital divide, a form of economic and social inequality in access to or use of information and communication technologies *Digital economy, an economy based on computing and telecommunications resources *Digital rights, legal rights of access to computers or the Internet Oth ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Instrumentation Amplifier
An instrumentation amplifier (sometimes shorthanded as in-amp or InAmp) is a type of differential amplifier that has been outfitted with input buffer amplifiers, which eliminate the need for input impedance matching and thus make the amplifier particularly suitable for use in measurement and test equipment. Additional characteristics include very low DC offset, low drift, low noise, very high open-loop gain, very high common-mode rejection ratio, and very high input impedances. Instrumentation amplifiers are used where great accuracy and stability of the circuit both short- and long-term are required. Although the instrumentation amplifier is usually shown schematically identical to a standard operational amplifier (op-amp), the electronic instrumentation amplifier is almost always internally composed of 3 op-amps. These are arranged so that there is one op-amp to buffer each input (+, −), and one to produce the desired output with adequate impedance matching for the ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Console Automation
In music recording, mix automation allows the mixing console to remember the audio engineer's adjustment of faders during the post-production editing process. A timecode is necessary for the synchronization of automation. Modern mixing consoles and digital audio workstations use comprehensive mix automation. The need for mix automation originates from the 1970s and the changeover from studios mostly using eight-track tape machines to multiple, synchronized 24-track recorders. Mixing could be laborious and require up to four people, and the results could be almost impossible to reproduce. Manufacturers such as Solid State Logic and AMS Neve developed systems that enabled one engineer to oversee every detail of a complex mix, although the computers required to power these desks remained a rarity into the late 1970s. According to record producer Roy Thomas Baker, Queen's 1975 single "Bohemian Rhapsody" was one of the first mixes to be done with automation. Types ;Voltage ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Motorized Potentiometer
A motorized potentiometer combines a potentiometer with an electric motor. Uses Motorized potentiometers can be found in audio/video equipment, specifically mixing consoles. In this application, they are called ''motorized faders''. Mixing consoles with motorized faders typically are used to save and restore settings on the same console and sometimes to transfer settings to a different console. Save and restore also allows to control more channels then there are sliders by switching which tracks are controlled.https://thehomerecordings.com/mixers-motorized-moving-faders/ While historically, the faders where literal motorized potentiometers, nowadays faders may directly digitize the fader position and apply the value digitally in the digital signal processing. Motorized potentiometers are used in industrial controls. Motorized potentiometers may be used for remote control applications. Motorized potentiometers can be used to build electrical/electronic analog computers. The ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Digital-to-analog Converter
In electronics, a digital-to-analog converter (DAC, D/A, D2A, or D-to-A) is a system that converts a digital signal into an analog signal. An analog-to-digital converter (ADC) performs the reverse function. DACs are commonly used in music players to convert digital data streams into analog audio signals. They are also used in televisions and mobile phones to convert digital video data into analog video signals. These two applications use DACs at opposite ends of the frequency/resolution trade-off. The audio DAC is a low-frequency, high-resolution type while the video DAC is a high-frequency low- to medium-resolution type. There are several DAC architectures; the suitability of a DAC for a particular application is determined by figures of merit including: resolution, maximum sampling frequency and others. Digital-to-analog conversion can degrade a signal, so a DAC should be specified that has insignificant errors in terms of the application. Due to the complexity ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Transmission Gate
A transmission gate (TG) is an analog gate similar to a relay that can conduct in both directions or block by a control signal with almost any voltage potential. It is a CMOS-based switch, in which PMOS passes a strong 1 but poor 0, and NMOS passes strong 0 but poor 1. Both PMOS and NMOS work simultaneously. Structure In principle, a transmission gate is made up of two field-effect transistors (FET), in which – in contrast to traditional discrete field-effect transistors – the substrate terminal (bulk) is not connected internally to the source terminal. The two transistors, an n-channel MOSFET and a p-channel MOSFET, are connected in parallel with the drain and source terminals of the two transistors connected together. Their gate terminals are connected to each other by a NOT gate (inverter), to form the control terminal. Unlike with discrete FETs, the substrate terminal is not connected to the source connection. Instead, the substrate terminals are connected to the resp ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
FPGA
A field-programmable gate array (FPGA) is a type of configurable integrated circuit that can be repeatedly programmed after manufacturing. FPGAs are a subset of logic devices referred to as programmable logic devices (PLDs). They consist of an array of programmable logic device, programmable logic block, logic blocks with a connecting grid, that can be configured "in the field" to interconnect with other logic blocks to perform various digital functions. FPGAs are often used in limited (low) quantity production of custom-made products, and in research and development, where the higher cost of individual FPGAs is not as important, and where creating and manufacturing a custom circuit would not be feasible. Other applications for FPGAs include the telecommunications, automotive, aerospace, and industrial sectors, which benefit from their flexibility, high signal processing speed, and parallel processing abilities. A FPGA configuration is generally written using a hardware descr ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Polysilicon
Polycrystalline silicon, or multicrystalline silicon, also called polysilicon, poly-Si, or mc-Si, is a high purity, polycrystalline form of silicon, used as a raw material by the solar photovoltaic and electronics industry. Polysilicon is produced from metallurgical grade silicon by a chemical purification process, called the Siemens process. This process involves distillation of volatile silicon compounds, and their decomposition into silicon at high temperatures. An emerging, alternative process of refinement uses a fluidized bed reactor which is lower cost. The photovoltaic industry also produces upgraded metallurgical-grade silicon (UMG-Si), using metallurgical instead of chemical purification processes for lower cost at the expense of purity. When produced for the electronics industry, polysilicon contains impurity levels of less than one part per billion (ppb), while polycrystalline solar grade silicon (SoG-Si) is generally less pure. In the 2010's, production shifte ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Serial Peripheral Interface
Serial Peripheral Interface (SPI) is a de facto standard (with many variants) for synchronous serial communication, used primarily in embedded systems for short-distance wired communication between integrated circuits. SPI follows a master–slave architecture, where a master device orchestrates communication with one or more slave devices by driving the clock and chip select signals. Some devices support changing master and slave roles on the fly. Motorola's original specification (from the early 1980s) uses four logic signals, aka lines or wires, to support full duplex communication. It is sometimes called a ''four-wire'' serial bus to contrast with three-wire variants which are half duplex, and with the ''two-wire'' I²C and 1-Wire serial buses. Typical applications include interfacing microcontrollers with peripheral chips for Secure Digital cards, liquid crystal displays, analog-to-digital and digital-to-analog converters, flash and EEPROM memory, and various ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Potentiometer
A potentiometer is a three- terminal resistor with a sliding or rotating contact that forms an adjustable voltage divider. If only two terminals are used, one end and the wiper, it acts as a variable resistor or rheostat. The measuring instrument called a potentiometer is essentially a voltage divider used for measuring electric potential (voltage); the component is an implementation of the same principle, hence its name. Potentiometers are commonly used to control electrical devices such as volume controls on audio equipment. It is also used in speed control of fans. Potentiometers operated by a mechanism can be used as position transducers, for example, in a joystick. Potentiometers are rarely used to directly control significant power (more than a watt), since the power dissipated in the potentiometer would be comparable to the power in the controlled load. Nomenclature Some terms in the electronics industry used to describe certain types of potentiometers are: * Pot: ab ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
I²C
I2C (Inter-Integrated Circuit; pronounced as "" or ""), alternatively known as I2C and IIC, is a synchronous, multi-master/multi-slave, single-ended, serial communication bus invented in 1980 by Philips Semiconductors (now NXP Semiconductors). It is widely used for attaching lower-speed peripheral integrated circuits (ICs) to processors and microcontrollers in short-distance, intra-board communication. The I2C bus can be found in a wide range of electronics applications where simplicity and low manufacturing cost are more important than speed. PC components and systems which involve I2C include serial presence detect (SPD) EEPROMs on dual in-line memory modules (DIMMs) and Extended Display Identification Data (EDID) for monitors via VGA, DVI, and HDMI connectors. Common I2C applications include reading hardware monitors, sensors, real-time clocks, controlling actuators, accessing low-speed DACs and ADCs, controlling simple LCD or OLED displays, changing computer ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Digital-to-analog Converter
In electronics, a digital-to-analog converter (DAC, D/A, D2A, or D-to-A) is a system that converts a digital signal into an analog signal. An analog-to-digital converter (ADC) performs the reverse function. DACs are commonly used in music players to convert digital data streams into analog audio signals. They are also used in televisions and mobile phones to convert digital video data into analog video signals. These two applications use DACs at opposite ends of the frequency/resolution trade-off. The audio DAC is a low-frequency, high-resolution type while the video DAC is a high-frequency low- to medium-resolution type. There are several DAC architectures; the suitability of a DAC for a particular application is determined by figures of merit including: resolution, maximum sampling frequency and others. Digital-to-analog conversion can degrade a signal, so a DAC should be specified that has insignificant errors in terms of the application. Due to the complexity ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
