Latency is a time interval between the stimulation and response, or, from a more general point of view, a time delay between the cause and the effect of some physical change in the system being observed. Latency is physically a consequence of the limited velocity with which any physical interaction can propagate. The magnitude of this velocity is always less than or equal to the speed of light. Therefore, every physical system will experience some sort of latency, regardless of the nature of stimulation that it has been exposed to.
The precise definition of latency depends on the system being observed and the nature of stimulation. In communications, the lower limit of latency is determined by the medium being used for communications. In reliable two-way communication systems, latency limits the maximum rate that information can be transmitted, as there is often a limit on the amount of information that is "in-flight" at any one moment. In the field of human–machine interaction, perceptible latency has a strong effect on user satisfaction and usability.
Online games are sensitive to latency since fast response times to new events occurring during a game session are rewarded while slow response times may carry penalties. Lag is the term used to describe latency in gaming. Due to a delay in transmission of game events, a player with a high latency internet connection may show slow responses in spite of appropriate reaction time. This gives players with low latency connections a technical advantage.
Minimizing latency is of interest in the capital markets, particularly where algorithmic trading is used to process market updates and turn around orders within milliseconds. Low-latency trading occurs on the networks used by financial institutions to connect to stock exchanges and electronic communication networks (ECNs) to execute financial transactions. Joel Hasbrouck and Gideon Saar (2011) measure latency based on three components: the time it takes for information to reach the trader, execution of the trader’s algorithms to analyze the information and decide a course of action, and the generated action to reach the exchange and get implemented. Hasbrouck and Saar contrast this with the way in which latencies are measured by many trading venues who use much more narrow definitions, such as, the processing delay measured from the entry of the order (at the vendor’s computer) to the transmission of an acknowledgement (from the vendor’s computer). Electronic trading now makes up 60% to 70% of the daily volume on the NYSE and algorithmic trading close to 35%. Trading using computers has developed to the point where millisecond improvements in network speeds offer a competitive advantage for financial institutions.
Network latency in a packet-switched network is measured either one-way (the time from the source sending a packet to the destination receiving it), or round-trip delay time (the one-way latency from source to destination plus the one-way latency from the destination back to the source). Round-trip latency is more often quoted, because it can be measured from a single point. Note that round trip latency excludes the amount of time that a destination system spends processing the packet. Many software platforms provide a service called ping that can be used to measure round-trip latency. Ping performs no packet processing; it merely sends a response back when it receives a packet (i.e. performs a no-op), thus it is a first rough way of measuring latency. Ping cannot perform accurate measurements, principally because it uses the ICMP protocol that is used only for diagnostic or control purposes, and differs from real communication protocols such as TCP. Furthermore, routers and ISP's might apply different traffic shaping policies to different protocols.
For more accurate measurements it is better to use specific software (for example: lft, paketto, hping, superping.d, NetPerf, IPerf)
However, in a non-trivial network, a typical packet will be forwarded over many links via many gateways, each of which will not begin to forward the packet until it has been completely received. In such a network, the minimal latency is the sum of the minimum latency of each link, plus the transmission delay of each link except the final one, plus the forwarding latency of each gateway. In practice, this minimal latency is further augmented by queuing and processing delays. Queuing delay occurs when a gateway receives multiple packets from different sources heading towards the same destination. Since typically only one packet can be transmitted at a time, some of the packets must queue for transmission, incurring additional delay. Processing delays are incurred while a gateway determines what to do with a newly received packet. A new and emergent behavior called bufferbloat can also cause increased latency that is an order of magnitude or more. The combination of propagation, serialization, queuing, and processing delays often produces a complex and variable network latency profile.
Latency limits total throughput in reliable two-way communication systems as described by the bandwidth-delay product.
Latency is largely a function of the speed of light, which is 299,792,458 meters/second in vacuum. This would equate to a latency of 3.33 µs for every kilometer of path length. The index of refraction of most fibre optic cables is about 1.5, meaning that light travels about 1.5 times as fast in a vacuum as it does in the cable. This works out to about 5.0 µs of latency for every kilometer. In shorter metro networks, the latency performance rises a bit more due to building risers and cross-connects and can push the latency over 5 µs per kilometer.
It follows that to calculate latency of a connection, one has to know the distance traveled by the fibre, which is rarely a straight line, since it has to traverse geographic contours and obstacles, such as roads and railway tracks, as well as other rights-of-way. Due to imperfections in the fibre, light degrades as it is transmitted through it. For distances of greater than 100 kilometers, either amplifiers or regenerators need to be deployed. Passive amplifiers typically add less latency than regenerators, at the cost of compounding attenuation, though in both cases it can be highly variable, and so needs to be taken into account. In particular, legacy spans are more likely to make use of higher latency regenerators.
This is illustrated when a news presenter in a studio talks with a reporter in a distant place via a geostationary communication satellite. The signal travels from the newsreader up to and down from the satellite to the reporter and then the reply from the reporter does the same, resulting in four satellite hops incurring a latency on the order of a half second, not including the typically smaller latencies inside the communications equipment.
Low-Earth orbit is sometimes used to cut this delay, at the expense of more complicated satellite tracking on the ground and requiring more satellites in the satellite constellation to ensure continuous coverage.
Audio latency is the delay between when an audio signal enters and when it emerges from a system. Potential contributors to latency in an audio system include analog-to-digital conversion, buffering, digital signal processing, transmission time, digital-to-analog conversion and the speed of sound in air.
Any individual workflow within a system of workflows can be subject to some type of operational latency. It may even be the case that an individual system may have more than one type of latency, depending on the type of participant or goal-seeking behavior. This is best illustrated by the following two examples involving air travel.
From the point of view of a passenger, latency can be described as follows. Suppose John Doe flies from London to New York. The latency of his trip is the time it takes him to go from his house in England to the hotel he is staying at in New York. This is independent of the throughput of the London-New York air link – whether there were 100 passengers a day making the trip or 10000, the latency of the trip would remain the same.
From the point of view of flight operations personnel, latency can be entirely different. Consider the staff at the London and New York airports. Only a limited number of planes are able to make the transatlantic journey, so when one lands they must prepare it for the return trip as quickly as possible. It might take, for example:
Assuming the above are done one after another, minimum plane turnaround time is:
However, cleaning, refueling and loading the cargo can be done at the same time. Passengers can be loaded after cleaning is complete. The reduced latency, then, is:
The people involved in the turnaround are interested only in the time it takes for their individual tasks. When all of the tasks are done at the same time, however, it is possible to reduce the latency to the length of the longest task. If some steps have prerequisites, it becomes more difficult to perform all steps in parallel. In the example above, the requirement to clean the plane before loading passengers results in a minimum latency longer than any single task.
Any mechanical process encounters limitations modeled by Newtonian physics. The behavior of disk drives provides an example of mechanical latency. Here, it is the time needed for the data encoded on a platter to rotate from its current position to a position adjacent to the read-write head as well as the seek time required for the actuator arm for the read-write head to be positioned above the appropriate track. This is also known as rotational latency and seek time since the basic term latency is also applied to the time required by a computer's electronics and software to perform polling, interrupts, and direct memory access.
Computers run sets of instructions called a process. In operating systems, the execution of the process can be postponed if other processes are also executing. In addition, the operating system can schedule when to perform the action that the process is commanding. For example, suppose a process commands that a computer card's voltage output be set high-low-high-low and so on at a rate of 1000 Hz. The operating system may choose to adjust the scheduling of each transition (high-low or low-high) based on an internal clock. The latency is the delay between the process instruction commanding the transition and the hardware actually transitioning the voltage from high to low or low to high.
On Microsoft Windows, it appears[original research?] that the timing of commands to hardware is not exact. Empirical data suggest that Windows (using the Windows sleep timer which accepts millisecond sleep times) will schedule on a 1024 Hz clock and will delay 24 of 1024 transitions per second to make an average of 1000 Hz for the update rate. This can have serious ramifications for discrete-time algorithms that rely on fairly consistent timing between updates such as those found in control theory. The sleep function or similar windows API were at no point designed for accurate timing purposes. Certain multimedia-oriented API routines like
timeGetTime() and its siblings provide better timing consistency. However, consumer- and server-grade Windows (as of 2011[update] those based on NT kernel) were not to be real-time operating systems. Drastically more accurate timings could be achieved by using dedicated hardware extensions and control-loop cards.
Linux may have the same problems with scheduling of hardware I/O. The problem in Linux is mitigated by support for posix real-time extensions, and the possibility of using a kernel with the PREEMPT_RT patch applied.
On embedded systems, the real-time execution of instructions is often supported by the low-level embedded operating system.
In simulation applications, 'latency' refers to the time delay, normally measured in milliseconds (1/1,000 sec), between initial input and an output clearly discernible to the simulator trainee or simulator subject. Latency is sometimes also called transport delay.
extracting tiny slices of profit from trading small numbers of shares in companies, often between different trading platforms, with success relying on minimal variations in speed - or "latency", in the trading vernacular.