The Metcalf is an American

sailboat A sailboat or sailing boat is a boat propelled partly or entirely by sails and is smaller than a sailing ship. Distinctions in what constitutes a sailing boat and ship vary by region and maritime culture. Types Although sailboat terminology ...

that was designed by

Bill Lapworth Charles William Lapworth (12 December 1919 – 3 April 2006) was an American naval architect who designed a large number of sailboats, many of them for Cal Yachts. He was active as a designer from the early 1950s until the 1980s. Described as " ...

as a racer and first built in 1960. The boat is named for Darby Metcalf who built the first example.

Production

The design was built by

W. D. Schock Corp The W. D. Schock Corporation (usually styled W. D. Schock Corp) is an American boat builder originally based in Newport Beach, California, later in Corona, California and currently located in Santa Ana, California. The company was founded by Wi ...

in the United States, starting in 1960, with 450 boats completed, but it is now out of production.

Design

The Metcalf is a racing, planing,

sailing dinghy Dinghy sailing is the activity of sailing small boats by using five essential controls: * the sails * the foils (i.e. the daggerboard or centreboard and rudder and sometimes lifting foils as found on the Moth) * the trim (forward/rear angle of ...

, built predominantly of

fiberglass Fiberglass (American English) or fibreglass (Commonwealth English) is a common type of fiber-reinforced plastic using glass fiber. The fibers may be randomly arranged, flattened into a sheet called a chopped strand mat, or woven into glass cloth ...

, with wood trim. It has a

cat rig A catboat (alternate spelling: cat boat) is a sailboat with a single sail on a single mast set well forward in the bow of a very beamy and (usually) shallow draft hull. Typically they are gaff rigged, though Bermuda rig is also used. Most are ...

with an

anodized Anodizing is an electrolytic passivation process used to increase the thickness of the natural oxide layer on the surface of metal parts. The process is called ''anodizing'' because the part to be treated forms the anode electrode of an electro ...

aluminum Aluminium (aluminum in American and Canadian English) is a chemical element with the symbol Al and atomic number 13. Aluminium has a density lower than those of other common metals, at approximately one third that of steel. It has ...

mast and

stainless steel Stainless steel is an alloy of iron that is resistant to rusting and corrosion. It contains at least 11% chromium and may contain elements such as carbon, other nonmetals and metals to obtain other desired properties. Stainless steel's corros ...

standing rigging Standing rigging comprises the fixed lines, wires, or rods, which support each mast or bowsprit on a sailing vessel and reinforce those spars against wind loads transferred from the sails. This term is used in contrast to running rigging, whic ...

. The hull has a

raked stem The stem is the most forward part of a boat or ship's bow and is an extension of the keel itself. It is often found on wooden boats or ships, but not exclusively. Description The stem is the curved edge stretching from the keel below, up to ...

, a plumb

transom Transom may refer to: * Transom (architecture), a bar of wood or stone across the top of a door or window, or the window above such a bar * Transom (nautical), that part of the stern of a vessel where the two sides of its hull meet * Operation Tran ...

, a transom-hung

rudder A rudder is a primary control surface used to steer a ship, boat, submarine, hovercraft, aircraft, or other vehicle that moves through a fluid medium (generally aircraft, air or watercraft, water). On an aircraft the rudder is used primarily to ...

controlled by a

tiller A tiller or till is a lever used to steer a vehicle. The mechanism is primarily used in watercraft, where it is attached to an outboard motor, rudder post or stock to provide leverage in the form of torque for the helmsman to turn the rudder. ...

and a retractable

daggerboard A daggerboard is a retractable centreboard used by various sailing craft. While other types of centreboard may pivot to retract, a daggerboard slides in a casing. The shape of the daggerboard converts the forward motion into a windward lift, cou ...

. It displaces . The boat has a draft of with the daggerboard extended and with it retracted, allowing operation in shallow water, beaching or ground transportation on a trailer or car roof top. The design has a

hull speed Hull speed or displacement speed is the speed at which the wavelength of a vessel's bow wave is equal to the waterline length of the vessel. As boat speed increases from rest, the wavelength of the bow wave increases, and usually its crest-to-tro ...

of .

References

{{Sailing dinghies and skiffs Dinghies 1960s sailboat type designs Sailing yachts Sailboat type designs by Bill Lapworth Sailboat types built by W. D. Schock Corp

Production

Design

See also

References