Electrical standards

Electricity is the set of

physical

phenomena associated with the presence and

motion

of matter that has a property of electric charge. Electricity is related to

magnetism

, both being part of the phenomenon of

electromagnetism

, as described by Maxwell's equations. Various common phenomena are related to electricity, including

lightning

,

static electricity

, electric heating, electric discharges and many others.

The presence of an electric charge, which can be either positive or negative, produces an

electric field

. The movement of electric charges is an electric current and produces a

magnetic field

.

When a charge is placed in a location with a non-zero electric field, a force will act on it. The magnitude of this force is given by Coulomb's law. If the charge moves, the electric field would be doing

work

on the electric charge. Thus we can speak of

electric potential

at a certain point in space, which is equal to the work done by an external agent in carrying a unit of positive charge from an arbitrarily chosen reference point to that point without any acceleration and is typically measured in

volt

s.

Electricity is at the heart of many modern technologies, being used for:
* Electric power where electric current is used to energise equipment;
* Electronics which deals with

electrical circuit

s that involve active electrical components such as vacuum tubes,

transistor

s,

diode

s and

integrated circuit

s, and associated passive interconnection technologies.

Electrical phenomena have been studied since antiquity, though progress in theoretical understanding remained slow until the seventeenth and eighteenth centuries. The theory of electromagnetism was developed in the 19th century, and by the end of that century electricity was being put to industrial and residential use by

electrical engineers

. The rapid expansion in electrical technology at this time transformed industry and society, becoming a driving force for the Second Industrial Revolution. Electricity's extraordinary versatility means it can be put to an almost limitless set of applications which include transport,

heating

, lighting, communications, and

computation

. Electrical power is now the backbone of modern industrial society.

History

Long before any knowledge of electricity existed, people were aware of shocks from electric fish.

Ancient Egypt

ian texts dating from 2750 BCE referred to these fish as the "Thunderer of the

Nile

", and described them as the "protectors" of all other fish. Electric fish were again reported millennia later by ancient Greek,

Roman

and Arabic naturalists and physicians. Several ancient writers, such as

Pliny the Elder

and Scribonius Largus, attested to the numbing effect of electric shocks delivered by electric catfish and electric rays, and knew that such shocks could travel along conducting objects.

Patients suffering from ailments such as

gout

or

headache

were directed to touch electric fish in the hope that the powerful jolt might cure them.

Ancient cultures around the Mediterranean knew that certain objects, such as rods of

amber

, could be rubbed with cat's fur to attract light objects like feathers.

Thales of Miletus

made a series of observations on

static electricity

around 600 BCE, from which he believed that friction rendered amber

magnetic

, in contrast to minerals such as

magnetite

, which needed no rubbing.

Thales was incorrect in believing the attraction was due to a magnetic effect, but later science would prove a link between magnetism and electricity. According to a controversial theory, the

Parthia

ns may have had knowledge of electroplating, based on the 1936 discovery of the Baghdad Battery, which resembles a galvanic cell, though it is uncertain whether the artifact was electrical in nature.

Electricity would remain little more than an intellectual curiosity for millennia until 1600, when the English scientist William Gilbert wrote ''De Magnete'', in which he made a careful study of electricity and magnetism, distinguishing the lodestone effect from static electricity produced by rubbing amber. He coined the New Latin word ''electricus'' ("of amber" or "like amber", from ἤλεκτρον, ''elektron'', the Greek word for "amber") to refer to the property of attracting small objects after being rubbed. This association gave rise to the English words "electric" and "electricity", which made their first appearance in print in Thomas Browne's ''Pseudodoxia Epidemica'' of 1646.

Further work was conducted in the 17th and early 18th centuries by

Otto von Guericke

,

Robert Boyle

, Stephen Gray and C. F. du Fay. Later in the 18th century,

Benjamin Franklin

conducted extensive research in electricity, selling his possessions to fund his work. In June 1752 he is reputed to have attached a metal key to the bottom of a dampened kite string and flown the kite in a storm-threatened sky. A succession of sparks jumping from the key to the back of his hand showed that

lightning

was indeed electrical in nature. He also explained the apparently paradoxical behavior of the

Leyden jar

as a device for storing large amounts of electrical charge in terms of electricity consisting of both positive and negative charges.

In 1791, Luigi Galvani published his discovery of bioelectromagnetics, demonstrating that electricity was the medium by which

neuron

s passed signals to the muscles.

Alessandro Volta

's battery, or

voltaic pile

, of 1800, made from alternating layers of zinc and copper, provided scientists with a more reliable source of electrical energy than the electrostatic machines previously used. The recognition of

electromagnetism

, the unity of electric and magnetic phenomena, is due to

Hans Christian Ørsted

and André-Marie Ampère in 1819–1820.

Michael Faraday

invented the

electric motor

in 1821, and Georg Ohm mathematically analysed the electrical circuit in 1827. Electricity and magnetism (and light) were definitively linked by

James Clerk Maxwell

, in particular in his "On Physical Lines of Force" in 1861 and 1862.

While the early 19th century had seen rapid progress in electrical science, the late 19th century would see the greatest progress in

electrical engineering

. Through such people as

Alexander Graham Bell

, Ottó Bláthy,

Thomas Edison

,

Galileo Ferraris

, Oliver Heaviside, Ányos Jedlik, William Thomson, 1st Baron Kelvin,

Charles Algernon Parsons

,

Werner von Siemens

, Joseph Swan, Reginald Fessenden,

Nikola Tesla

and

George Westinghouse

, electricity turned from a scientific curiosity into an essential tool for modern life.

In 1887,

Heinrich Hertz

discovered that

electrode

s illuminated with ultraviolet light create electric sparks more easily. In 1905,

Albert Einstein

published a paper that explained experimental data from the

photoelectric effect

as being the result of light energy being carried in discrete quantized packets, energising electrons. This discovery led to the

quantum

revolution. Einstein was awarded the Nobel Prize in Physics in 1921 for "his discovery of the law of the photoelectric effect". The photoelectric effect is also employed in

photocell

s such as can be found in

solar panel

s and this is frequently used to make electricity commercially.

The first solid-state device was the "cat's-whisker detector" first used in the 1900s in radio receivers. A whisker-like wire is placed lightly in contact with a solid crystal (such as a

germanium

crystal) to detect a

radio

signal by the contact junction effect. In a solid-state component, the current is confined to solid elements and compounds engineered specifically to switch and amplify it. Current flow can be understood in two forms: as negatively charged

electron

s, and as positively charged electron deficiencies called holes. These charges and holes are understood in terms of quantum physics. The building material is most often a crystalline semiconductor.

Solid-state electronics came into its own with the emergence of

transistor

technology. The first working transistor, a

germanium

-based

point-contact transistor

, was invented by John Bardeen and Walter Houser Brattain at Bell Labs in 1947, followed by the bipolar junction transistor in 1948. These early transistors were relatively bulky devices that were difficult to manufacture on a mass-production basis. They were followed by the

silicon

-based

MOSFET

(metal-oxide-semiconductor field-effect transistor, or MOS transistor), invented by

Mohamed M. Atalla

and

Dawon Kahng

at Bell Labs in 1959. It was the first truly compact transistor that could be miniaturised and mass-produced for a wide range of uses, leading to the silicon revolution. Solid-state devices started becoming prevalent from the 1960s, with the transition from vacuum tubes to semiconductor

diode

s, transistors,

integrated circuit

(IC) chips, MOSFETs, and light-emitting diode (LED) technology.

The most common electronic device is the MOSFET, which has become the most widely manufactured device in history. Common solid-state MOS devices include

microprocessor

chips and semiconductor memory. A special type of semiconductor memory is flash memory, which is used in

USB flash drive

s and mobile devices, as well as solid-state drive (SSD) technology to replace mechanically rotating magnetic disc

hard disk drive

(HDD) technology.

Concepts

Electric charge

The presence of charge gives rise to an electrostatic force: charges exert a

force

on each other, an effect that was known, though not understood, in antiquity.

A lightweight ball suspended from a string can be charged by touching it with a glass rod that has itself been charged by rubbing with a cloth. If a similar ball is charged by the same glass rod, it is found to repel the first: the charge acts to force the two balls apart. Two balls that are charged with a rubbed amber rod also repel each other. However, if one ball is charged by the glass rod, and the other by an amber rod, the two balls are found to attract each other. These phenomena were investigated in the late eighteenth century by Charles-Augustin de Coulomb, who deduced that charge manifests itself in two opposing forms. This discovery led to the well-known axiom: ''like-charged objects repel and opposite-charged objects attract''.

The force acts on the charged particles themselves, hence charge has a tendency to spread itself as evenly as possible over a conducting surface. The magnitude of the electromagnetic force, whether attractive or repulsive, is given by Coulomb's law, which relates the force to the product of the charges and has an inverse-square relation to the distance between them.

The electromagnetic force is very strong, second only in strength to the strong interaction, but unlike that force it operates over all distances.

In comparison with the much weaker gravitational force, the electromagnetic force pushing two electrons apart is 10⁴² times that of the gravitational attraction pulling them together.

Charge originates from certain types of subatomic particles, the most familiar carriers of which are the

electron

and proton. Electric charge gives rise to and interacts with the electromagnetic force, one of the four fundamental forces of nature. Experiment has shown charge to be a conserved quantity, that is, the net charge within an electrically isolated system will always remain constant regardless of any changes taking place within that system. Within the system, charge may be transferred between bodies, either by direct contact, or by passing along a conducting material, such as a wire. The informal term

static electricity

refers to the net presence (or 'imbalance') of charge on a body, usually caused when dissimilar materials are rubbed together, transferring charge from one to the other.

The charge on electrons and protons is opposite in sign, hence an amount of charge may be expressed as being either negative or positive. By convention, the charge carried by electrons is deemed negative, and that by protons positive, a custom that originated with the work of

Benjamin Franklin

. The amount of charge is usually given the symbol ''Q'' and expressed in coulombs; each electron carries the same charge of approximately −1.6022×10⁻¹⁹ coulomb. The proton has a charge that is equal and opposite, and thus +1.6022×10⁻¹⁹  coulomb. Charge is possessed not just by matter, but also by antimatter, each antiparticle bearing an equal and opposite charge to its corresponding particle.

Charge can be measured by a number of means, an early instrument being the gold-leaf electroscope, which although still in use for classroom demonstrations, has been superseded by the electronic electrometer.

Electric current

The movement of electric charge is known as an electric current, the intensity of which is usually measured in amperes. Current can consist of any moving charged particles; most commonly these are electrons, but any charge in motion constitutes a current. Electric current can flow through some things, electrical conductors, but will not flow through an electrical insulator.

By historical convention, a positive current is defined as having the same direction of flow as any positive charge it contains, or to flow from the most positive part of a circuit to the most negative part. Current defined in this manner is called conventional current. The motion of negatively charged electrons around an electric circuit, one of the most familiar forms of current, is thus deemed positive in the ''opposite'' direction to that of the electrons. However, depending on the conditions, an electric current can consist of a flow of charged particles in either direction, or even in both directions at once. The positive-to-negative convention is widely used to simplify this situation.

The process by which electric current passes through a material is termed electrical conduction, and its nature varies with that of the charged particles and the material through which they are travelling. Examples of electric currents include metallic conduction, where electrons flow through a Electrical conductor, conductor such as metal, and electrolysis, where ions (charged atoms) flow through liquids, or through plasma (physics), plasmas such as electrical sparks. While the particles themselves can move quite slowly, sometimes with an average drift velocity only fractions of a millimetre per second, the

electric field

that drives them itself propagates at close to the speed of light, enabling electrical signals to pass rapidly along wires.

Current causes several observable effects, which historically were the means of recognising its presence. That water could be decomposed by the current from a voltaic pile was discovered by William Nicholson (chemist), Nicholson and Anthony Carlisle, Carlisle in 1800, a process now known as electrolysis. Their work was greatly expanded upon by

Michael Faraday

in 1833. Current through a electrical resistance, resistance causes localised heating, an effect James Prescott Joule studied mathematically in 1840. One of the most important discoveries relating to current was made accidentally by

Hans Christian Ørsted

in 1820, when, while preparing a lecture, he witnessed the current in a wire disturbing the needle of a magnetic compass.
Accounts differ as to whether this was before, during, or after a lecture. He had discovered

electromagnetism

, a fundamental interaction between electricity and magnetics. The level of electromagnetic emissions generated by electric arcing is high enough to produce electromagnetic interference, which can be detrimental to the workings of adjacent equipment.

In engineering or household applications, current is often described as being either direct current (DC) or alternating current (AC). These terms refer to how the current varies in time. Direct current, as produced by example from a Battery (electricity), battery and required by most Electronics, electronic devices, is a unidirectional flow from the positive part of a circuit to the negative.

If, as is most common, this flow is carried by electrons, they will be travelling in the opposite direction. Alternating current is any current that reverses direction repeatedly; almost always this takes the form of a sine wave. Alternating current thus pulses back and forth within a conductor without the charge moving any net distance over time. The time-averaged value of an alternating current is zero, but it delivers energy in first one direction, and then the reverse. Alternating current is affected by electrical properties that are not observed under steady state direct current, such as inductance and capacitance. These properties however can become important when circuitry is subjected to transient response, transients, such as when first energised.

Electric field

The concept of the electric Field (physics), field was introduced by

Michael Faraday

. An electric field is created by a charged body in the space that surrounds it, and results in a force exerted on any other charges placed within the field. The electric field acts between two charges in a similar manner to the way that the gravitational field acts between two masses, and like it, extends towards infinity and shows an inverse square relationship with distance. However, there is an important difference. Gravity always acts in attraction, drawing two masses together, while the electric field can result in either attraction or repulsion. Since large bodies such as planets generally carry no net charge, the electric field at a distance is usually zero. Thus gravity is the dominant force at distance in the universe, despite being much weaker.

An electric field generally varies in space, and its strength at any one point is defined as the force (per unit charge) that would be felt by a stationary, negligible charge if placed at that point. The conceptual charge, termed a 'test charge', must be vanishingly small to prevent its own electric field disturbing the main field and must also be stationary to prevent the effect of

magnetic field

s. As the electric field is defined in terms of

force

, and force is a Euclidean vector, vector, having both Magnitude (mathematics), magnitude and Direction (geometry), direction, so it follows that an electric field is a vector field.

The study of electric fields created by stationary charges is called electrostatics. The field may be visualised by a set of imaginary lines whose direction at any point is the same as that of the field. This concept was introduced by Faraday,
whose term 'Line of force, lines of force' still sometimes sees use. The field lines are the paths that a point positive charge would seek to make as it was forced to move within the field; they are however an imaginary concept with no physical existence, and the field permeates all the intervening space between the lines. Field lines emanating from stationary charges have several key properties: first, that they originate at positive charges and terminate at negative charges; second, that they must enter any good conductor at right angles, and third, that they may never cross nor close in on themselves.

A hollow conducting body carries all its charge on its outer surface. The field is therefore zero at all places inside the body. This is the operating principal of the Faraday cage, a conducting metal shell which isolates its interior from outside electrical effects.

The principles of electrostatics are important when designing items of high voltage, high-voltage equipment. There is a finite limit to the electric field strength that may be withstood by any medium. Beyond this point, electrical breakdown occurs and an electric arc causes flashover between the charged parts. Air, for example, tends to arc across small gaps at electric field strengths which exceed 30 kV per centimetre. Over larger gaps, its breakdown strength is weaker, perhaps 1 kV per centimetre.

The most visible natural occurrence of this is

lightning

, caused when charge becomes separated in the clouds by rising columns of air, and raises the electric field in the air to greater than it can withstand. The voltage of a large lightning cloud may be as high as 100 MV and have discharge energies as great as 250 kWh.

The field strength is greatly affected by nearby conducting objects, and it is particularly intense when it is forced to curve around sharply pointed objects. This principle is exploited in the lightning conductor, the sharp spike of which acts to encourage the lightning stroke to develop there, rather than to the building it serves to protect

Electric potential

The concept of electric potential is closely linked to that of the electric field. A small charge placed within an electric field experiences a force, and to have brought that charge to that point against the force requires Mechanical work, work. The electric potential at any point is defined as the energy required to bring a unit test charge from an infinity, infinite distance slowly to that point. It is usually measured in

volt

s, and one volt is the potential for which one joule of work must be expended to bring a charge of one coulomb from infinity. This definition of potential, while formal, has little practical application, and a more useful concept is that of electric potential difference, and is the energy required to move a unit charge between two specified points. An electric field has the special property that it is ''Conservative force, conservative'', which means that the path taken by the test charge is irrelevant: all paths between two specified points expend the same energy, and thus a unique value for potential difference may be stated. The volt is so strongly identified as the unit of choice for measurement and description of electric potential difference that the term voltage sees greater everyday usage.

For practical purposes, it is useful to define a common reference point to which potentials may be expressed and compared. While this could be at infinity, a much more useful reference is the Earth itself, which is assumed to be at the same potential everywhere. This reference point naturally takes the name Ground (electricity), earth or Ground (electricity), ground. Earth is assumed to be an infinite source of equal amounts of positive and negative charge, and is therefore electrically uncharged—and unchargeable.

Electric potential is a scalar (physics), scalar quantity, that is, it has only magnitude and not direction. It may be viewed as analogous to height: just as a released object will fall through a difference in heights caused by a gravitational field, so a charge will 'fall' across the voltage caused by an electric field. As relief maps show contour lines marking points of equal height, a set of lines marking points of equal potential (known as equipotentials) may be drawn around an electrostatically charged object. The equipotentials cross all lines of force at right angles. They must also lie parallel to a electrical conductor, conductor's surface, otherwise this would produce a force that will move the charge carriers to even the potential of the surface.

The electric field was formally defined as the force exerted per unit charge, but the concept of potential allows for a more useful and equivalent definition: the electric field is the local gradient of the electric potential. Usually expressed in volts per metre, the vector direction of the field is the line of greatest slope of potential, and where the equipotentials lie closest together.

Electromagnets

Ørsted's discovery in 1821 that a

magnetic field

existed around all sides of a wire carrying an electric current indicated that there was a direct relationship between electricity and magnetism. Moreover, the interaction seemed different from gravitational and electrostatic forces, the two forces of nature then known. The force on the compass needle did not direct it to or away from the current-carrying wire, but acted at right angles to it. Ørsted's words were that "the electric conflict acts in a revolving manner." The force also depended on the direction of the current, for if the flow was reversed, then the force did too.

Ørsted did not fully understand his discovery, but he observed the effect was reciprocal: a current exerts a force on a magnet, and a magnetic field exerts a force on a current. The phenomenon was further investigated by André-Marie Ampère, Ampère, who discovered that two parallel current-carrying wires exerted a force upon each other: two wires conducting currents in the same direction are attracted to each other, while wires containing currents in opposite directions are forced apart.
The interaction is mediated by the magnetic field each current produces and forms the basis for the international Ampere#Definition, definition of the ampere.

This relationship between magnetic fields and currents is extremely important, for it led to Michael Faraday's invention of the

electric motor

in 1821. Faraday's homopolar motor consisted of a permanent magnet sitting in a pool of Mercury (element), mercury. A current was allowed through a wire suspended from a pivot above the magnet and dipped into the mercury. The magnet exerted a tangential force on the wire, making it circle around the magnet for as long as the current was maintained.

Experimentation by Faraday in 1831 revealed that a wire moving perpendicular to a magnetic field developed a potential difference between its ends. Further analysis of this process, known as electromagnetic induction, enabled him to state the principle, now known as Faraday's law of induction, that the potential difference induced in a closed circuit is proportional to the rate of change of magnetic flux through the loop. Exploitation of this discovery enabled him to invent the first electrical generator in 1831, in which he converted the mechanical energy of a rotating copper disc to electrical energy. Faraday's disc was inefficient and of no use as a practical generator, but it showed the possibility of generating electric power using magnetism, a possibility that would be taken up by those that followed on from his work.

Electrochemistry

The ability of chemical reactions to produce electricity, and conversely the ability of electricity to drive chemical reactions has a wide array of uses.

Electrochemistry has always been an important part of electricity. From the initial invention of the Voltaic pile, electrochemical cells have evolved into the many different types of batteries, electroplating and electrolysis cells. Aluminium is produced in vast quantities this way, and many portable devices are electrically powered using rechargeable cells.

Electric circuits

An electric circuit is an interconnection of electric components such that electric charge is made to flow along a closed path (a circuit), usually to perform some useful task.

The components in an electric circuit can take many forms, which can include elements such as resistors, capacitors, switches, transformers and electronics. Electronic circuits contain active components, usually semiconductors, and typically exhibit non-linear behaviour, requiring complex analysis. The simplest electric components are those that are termed passivity (engineering), passive and linear: while they may temporarily store energy, they contain no sources of it, and exhibit linear responses to stimuli.

The resistor is perhaps the simplest of passive circuit elements: as its name suggests, it Electrical resistance, resists the current through it, dissipating its energy as heat. The resistance is a consequence of the motion of charge through a conductor: in metals, for example, resistance is primarily due to collisions between electrons and ions. Ohm's law is a basic law of circuit theory, stating that the current passing through a resistance is directly proportional to the potential difference across it. The resistance of most materials is relatively constant over a range of temperatures and currents; materials under these conditions are known as 'ohmic'. The ohm, the unit of resistance, was named in honour of Georg Ohm, and is symbolised by the Greek letter Ω. 1 Ω is the resistance that will produce a potential difference of one volt in response to a current of one amp.

The capacitor is a development of the Leyden jar and is a device that can store charge, and thereby storing electrical energy in the resulting field. It consists of two conducting plates separated by a thin Insulator (electricity), insulating dielectric layer; in practice, thin metal foils are coiled together, increasing the surface area per unit volume and therefore the capacitance. The unit of capacitance is the farad, named after

Michael Faraday

, and given the symbol ''F'': one farad is the capacitance that develops a potential difference of one volt when it stores a charge of one coulomb. A capacitor connected to a voltage supply initially causes a current as it accumulates charge; this current will however decay in time as the capacitor fills, eventually falling to zero. A capacitor will therefore not permit a steady state current, but instead blocks it.

The inductor is a conductor, usually a coil of wire, that stores energy in a magnetic field in response to the current through it. When the current changes, the magnetic field does too, electromagnetic induction, inducing a voltage between the ends of the conductor. The induced voltage is proportional to the Time derivative, time rate of change of the current. The constant of proportionality is termed the inductance. The unit of inductance is the Henry (unit), henry, named after Joseph Henry, a contemporary of Faraday. One henry is the inductance that will induce a potential difference of one volt if the current through it changes at a rate of one ampere per second. The inductor's behaviour is in some regards converse to that of the capacitor: it will freely allow an unchanging current, but opposes a rapidly changing one.

Electric power

Electric power is the rate at which electric energy is transferred by an electric circuit. The SI unit of power (physics), power is the watt (unit), watt, one joule per second.

Electric power, like power (physics), mechanical power, is the rate of doing work (electrical), work, measured in watts, and represented by the letter ''P''. The term ''wattage'' is used colloquially to mean "electric power in watts." The electric power in watts produced by an electric current ''I'' consisting of a charge of ''Q'' coulombs every ''t'' seconds passing through an

electric potential

(voltage) difference of ''V'' is
:$P = \text = \frac = IV \,$
where
:''Q'' is electric charge in coulombs
:''t'' is time in seconds
:''I'' is electric current in amperes
:''V'' is electric potential or voltage in

volt

s

Electricity generation is often done by a process of converting mechanical energy to electricity. Devices such as steam turbines or gas turbines are involved in the production of the mechanical energy, which is passed on to electric generators which produce the electricity. Electricity can also be supplied by chemical sources such as electric batteries or by other means from a wide variety of sources of energy. Electric power is generally supplied to businesses and homes by the electric power industry. Electricity is usually sold by the kilowatt hour (3.6 MJ) which is the product of power in kilowatts multiplied by running time in hours. Electric utilities measure power using electricity meters, which keep a running total of the electric energy delivered to a customer. Unlike fossil fuels, electricity is a low entropy form of energy and can be converted into motion or many other forms of energy with high efficiency.

Electronics

Electronics deals with

electrical circuit

s that involve active component, active electrical components such as vacuum tubes,

transistor

s,

diode

s, optoelectronics, sensors and

integrated circuit

s, and associated passive interconnection technologies. The nonlinear behaviour of active components and their ability to control electron flows makes amplification of weak signals possible and electronics is widely used in information processing, telecommunications, and signal processing. The ability of electronic devices to act as switches makes digital information processing possible. Interconnection technologies such as circuit boards, electronics packaging technology, and other varied forms of communication infrastructure complete circuit functionality and transform the mixed components into a regular working system.

Today, most electronic devices use semiconductor components to perform electron control. The study of semiconductor devices and related technology is considered a branch of solid state physics, whereas the design and construction of electronic circuits to solve practical problems come under electronics engineering.

Electromagnetic wave

Faraday's and Ampère's work showed that a time-varying magnetic field acted as a source of an electric field, and a time-varying electric field was a source of a magnetic field. Thus, when either field is changing in time, then a field of the other is necessarily induced. Such a phenomenon has the properties of a wave, and is naturally referred to as an electromagnetic wave. Electromagnetic waves were analysed theoretically by

James Clerk Maxwell

in 1864. Maxwell developed a set of equations that could unambiguously describe the interrelationship between electric field, magnetic field, electric charge, and electric current. He could moreover prove that such a wave would necessarily travel at the speed of light, and thus light itself was a form of electromagnetic radiation. Maxwell's Laws, which unify light, fields, and charge are one of the great milestones of theoretical physics.

Thus, the work of many researchers enabled the use of electronics to convert signals into radio frequency, high frequency oscillating currents, and via suitably shaped conductors, electricity permits the transmission and reception of these signals via radio waves over very long distances.

Production and uses

Generation and transmission

In the 6th century BC, the Greek philosopher

Thales of Miletus

experimented with amber rods and these experiments were the first studies into the production of electrical energy. While this method, now known as the triboelectric effect, can lift light objects and generate sparks, it is extremely inefficient.

It was not until the invention of the

voltaic pile

in the eighteenth century that a viable source of electricity became available. The voltaic pile, and its modern descendant, the Battery (electricity), electrical battery, store energy chemically and make it available on demand in the form of electrical energy. The battery is a versatile and very common power source which is ideally suited to many applications, but its energy storage is finite, and once discharged it must be disposed of or recharged. For large electrical demands electrical energy must be generated and transmitted continuously over conductive transmission lines.

Electrical power is usually generated by electro-mechanical electrical generator, generators driven by steam produced from fossil fuel combustion, or the heat released from nuclear reactions; or from other sources such as kinetic energy extracted from wind or flowing water. The modern steam turbine invented by Charles Algernon Parsons, Sir Charles Parsons in 1884 today generates about 80 percent of the electric power in the world using a variety of heat sources. Such generators bear no resemblance to Faraday's homopolar disc generator of 1831, but they still rely on his electromagnetic principle that a conductor linking a changing magnetic field induces a potential difference across its ends. The invention in the late nineteenth century of the transformer meant that electrical power could be transmitted more efficiently at a higher voltage but lower current. Efficient electrical transmission meant in turn that electricity could be generated at centralised power stations, where it benefited from economies of scale, and then be despatched relatively long distances to where it was needed.

Since electrical energy cannot easily be stored in quantities large enough to meet demands on a national scale, at all times exactly as much must be produced as is required. This requires Electric utility, electricity utilities to make careful predictions of their electrical loads, and maintain constant co-ordination with their power stations. A certain amount of generation must always be held in Operating reserve, reserve to cushion an electrical grid against inevitable disturbances and losses.

Demand for electricity grows with great rapidity as a nation modernises and its economy develops. The United States showed a 12% increase in demand during each year of the first three decades of the twentieth century, a rate of growth that is now being experienced by emerging economies such as those of India or China. Historically, the growth rate for electricity demand has outstripped that for other forms of energy.

Environmental concerns with electricity generation have led to an increased focus on generation from Renewable energy, renewable sources, in particular from wind power, wind and solar power, solar. While debate can be expected to continue over the environmental impact of different means of electricity production, its final form is relatively clean.

Applications

Electricity is a very convenient way to transfer energy, and it has been adapted to a huge, and growing, number of uses. The invention of a practical incandescent light bulb in the 1870s led to lighting becoming one of the first publicly available applications of electrical power. Although electrification brought with it its own dangers, replacing the naked flames of gas lighting greatly reduced fire hazards within homes and factories. Public utilities were set up in many cities targeting the burgeoning market for electrical lighting. In the late 20th century and in modern times, the trend has started to flow in the direction of deregulation in the electrical power sector.

The resistive Joule heating effect employed in filament light bulbs also sees more direct use in electric heating. While this is versatile and controllable, it can be seen as wasteful, since most electrical generation has already required the production of heat at a power station. A number of countries, such as Denmark, have issued legislation restricting or banning the use of resistive electric heating in new buildings. Electricity is however still a highly practical energy source for heating and refrigeration, with air conditioning/heat pumps representing a growing sector for electricity demand for heating and cooling, the effects of which electricity utilities are increasingly obliged to accommodate.

Electricity is used within telecommunications, and indeed the electrical telegraph, demonstrated commercially in 1837 by William Fothergill Cooke, Cooke and Charles Wheatstone, Wheatstone, was one of its earliest applications. With the construction of first First Transcontinental Telegraph, transcontinental, and then Transatlantic telegraph cable, transatlantic, telegraph systems in the 1860s, electricity had enabled communications in minutes across the globe. Optical fibre and Communications satellite, satellite communication have taken a share of the market for communications systems, but electricity can be expected to remain an essential part of the process.

The effects of electromagnetism are most visibly employed in the

electric motor

, which provides a clean and efficient means of motive power. A stationary motor such as a winch is easily provided with a supply of power, but a motor that moves with its application, such as an electric vehicle, is obliged to either carry along a power source such as a battery, or to collect current from a sliding contact such as a Pantograph (rail), pantograph. Electrically powered vehicles are used in public transportation, such as electric buses and trains, and an increasing number of battery-powered electric cars in private ownership.

Electronic devices make use of the

transistor

, perhaps one of the most important inventions of the twentieth century, and a fundamental building block of all modern circuitry. A modern

integrated circuit

may contain several billion miniaturised transistors in a region only a few centimetres square.

Electricity and the natural world

Physiological effects

A voltage applied to a human body causes an electric current through the tissues, and although the relationship is non-linear, the greater the voltage, the greater the current.

The threshold for perception varies with the supply frequency and with the path of the current, but is about 0.1 mA to 1 mA for mains-frequency electricity, though a current as low as a microamp can be detected as an electrovibration effect under certain conditions. If the current is sufficiently high, it will cause muscle contraction, fibrillation of the heart, and burn, tissue burns. The lack of any visible sign that a conductor is electrified makes electricity a particular hazard. The pain caused by an electric shock can be intense, leading electricity at times to be employed as a method of torture. Death caused by an electric shock is referred to as electric shock, electrocution. Electrocution is still the means of capital punishment, judicial execution in some jurisdictions, though its use has become rarer in recent times.

Electrical phenomena in nature

Electricity is not a human invention, and may be observed in several forms in nature, a prominent manifestation of which is

lightning

. Many interactions familiar at the macroscopic level, such as touch, friction or chemical bonding, are due to interactions between electric fields on the atomic scale. The Earth's magnetic field is thought to arise from a dynamo theory, natural dynamo of circulating currents in the planet's core. Certain crystals, such as quartz, or even sugar, generate a potential difference across their faces when subjected to external pressure.

This phenomenon is known as piezoelectricity, from the Greek language, Greek ''piezein'' (πιέζειν), meaning to press, and was discovered in 1880 by Pierre Curie, Pierre and Jacques Curie. The effect is reciprocal, and when a piezoelectric material is subjected to an electric field, a small change in physical dimensions takes place.

Bioelectrogenesis#Bioelectrogenesis in microbial life, §Bioelectrogenesis in microbial life is a prominent phenomenon in soils and sediment ecology resulting from anaerobic respiration. The microbial fuel cell mimics this ubiquitous natural phenomenon.

Some organisms, such as sharks, are able to detect and respond to changes in electric fields, an ability known as electroreception,

while others, termed electrogenic, are able to generate voltages themselves to serve as a predatory or defensive weapon. The order Gymnotiformes, of which the best known example is the electric eel, detect or stun their prey via high voltages generated from modified muscle cells called electrocytes. All animals transmit information along their cell membranes with voltage pulses called action potentials, whose functions include communication by the nervous system between

neuron

s and muscles.

An electric shock stimulates this system, and causes muscles to contract. Action potentials are also responsible for coordinating activities in certain plants.

Cultural perception

In 1850, William Gladstone asked the scientist

Michael Faraday

why electricity was valuable. Faraday answered, “One day sir, you may tax it.”

In the 19th and early 20th century, electricity was not part of the everyday life of many people, even in the industrialised Western world. The popular culture of the time accordingly often depicted it as a mysterious, quasi-magical force that can slay the living, revive the dead or otherwise bend the laws of nature. This attitude began with the 1771 experiments of Luigi Galvani in which the legs of dead frogs were shown to twitch on application of galvanism, animal electricity. "Revitalization" or resuscitation of apparently dead or drowned persons was reported in the medical literature shortly after Galvani's work. These results were known to Mary Shelley when she authored ''Frankenstein'' (1819), although she does not name the method of revitalization of the monster. The revitalization of monsters with electricity later became a stock theme in horror films.

As the public familiarity with electricity as the lifeblood of the Second Industrial Revolution grew, its wielders were more often cast in a positive light,Van Riper, op.cit., p. 71. such as the workers who "finger death at their gloves' end as they piece and repiece the living wires" in Rudyard Kipling's 1907 poem ''Sons of Martha''. Electrically powered vehicles of every sort featured large in adventure stories such as those of Jules Verne and the ''Tom Swift'' books. The masters of electricity, whether fictional or real—including scientists such as

Thomas Edison

, Charles Steinmetz or

Nikola Tesla

—were popularly conceived of as having wizard-like powers.

With electricity ceasing to be a novelty and becoming a necessity of everyday life in the later half of the 20th century, it required particular attention by popular culture only when it ''stops'' flowing, an event that usually signals disaster. The people who ''keep'' it flowing, such as the nameless hero of Jimmy Webb’s song "Wichita Lineman" (1968), are still often cast as heroic, wizard-like figures.

See also

* Ampère's circuital law, connects the direction of an electric current and its associated magnetic currents.
* Electric potential energy, the potential energy of a system of charges
* Electricity market, the sale of electrical energy
*Etymology of electricity, Etymology of ''electricity'', the origin of the word ''electricity'' and its current different usages
* Hydraulic analogy, an analogy between the flow of water and electric current

Notes

References

*
*
*
*
*
*
* Benjamin, P. (1898)
A history of electricity (The intellectual rise in electricity) from antiquity to the days of Benjamin Franklin
New York: J. Wiley & Sons.

External links

chapter fro

book an
series


"One-Hundred Years of Electricity", May 1931, Popular Mechanics


* [http://www.worldstandards.eu/electricity/plugs-and-sockets/ Electricity around the world]

Electricity Misconceptions




* [http://water.worldbank.org/water/publications/water-electricity-and-poor-who-benefits-utility-subsidies/ World Bank report on Water, Electricity and Utility subsidies]

{{Authority control

Electricity,