electric dipole

The electric dipole moment is a measure of the separation of positive and negative electrical charges within a system, that is, a measure of the system's overall polarity. The SI unit for electric dipole moment is the coulomb-meter (C⋅m). The debye (D) is another unit of measurement used in atomic physics and chemistry.

Theoretically, an electric dipole is defined by the first-order term of the multipole expansion; it consists of two equal and opposite charges that are infinitesimally close together, although real dipoles have separated charge.Many theorists predict elementary particles can have very tiny electric dipole moments, possibly without separated charge. Such large dipoles make no difference to everyday physics, and have not yet been observed. (See electron electric dipole moment). However, when making measurements at a distance much larger than the charge separation, the dipole gives a good approximation of the actual electric field. The dipole is represented by a vector from the negative charge towards the positive charge.

Elementary definition

Often in physics the dimensions of a massive object can be ignored and can be treated as a pointlike object, i.e. a point particle. Point particles with electric charge are referred to as point charges. Two point charges, one with charge and the other one with charge separated by a distance , constitute an ''electric dipole'' (a simple case of an electric multipole). For this case, the electric dipole moment has a magnitude $p = qd$ and is directed from the negative charge to the positive one. Some authors may split in half and use since this quantity is the distance between either charge and the center of the dipole, leading to a factor of two in the definition.

A stronger mathematical definition is to use vector algebra, since a quantity with magnitude and direction, like the dipole moment of two point charges, can be expressed in vector form $\mathbf = q \mathbf$ where is the displacement vector pointing from the negative charge to the positive charge. The electric dipole moment vector also points from the negative charge to the positive charge. With this definition the dipole direction tends to align itself with an external electric field (and note that the electric flux lines produced by the charges of the dipole itself, which point from positive charge to negative charge then tend to oppose the flux lines of the external field). Note that this sign convention is used in physics, while the opposite sign convention for the dipole, from the positive charge to the negative charge, is used in chemistry.

An idealization of this two-charge system is the electrical point dipole consisting of two (infinite) charges only infinitesimally separated, but with a finite . This quantity is used in the definition of polarization density.

Energy and torque

An object with an electric dipole moment p is subject to a torque ''τ'' when placed in an external electric field E. The torque tends to align the dipole with the field. A dipole aligned parallel to an electric field has lower potential energy than a dipole making some angle with it. For a spatially uniform electric field across the small region occupied by the dipole, the energy ''U'' and the torque $\boldsymbol$ are given by
$U = - \mathbf \cdot \mathbf,\qquad\ \boldsymbol = \mathbf \times \mathbf,$

The scalar dot "" product and the negative sign shows the potential energy minimises when the dipole is parallel with field and is maximum when antiparallel while zero when perpendicular. The symbol "" refers to the vector cross product. The E-field vector and the dipole vector define a plane, and the torque is directed normal to that plane with the direction given by the right-hand rule. Note that a dipole in such a uniform field may twist and oscillate but receives no overall net force with no linear acceleration of the dipole. The dipole twists to align with the external field.

However in a non-uniform electric field a dipole may indeed receive a net force since the force on one end of the dipole no longer balances that on the other end. It can be shown that this net force is generally parallel to the dipole moment.

Expression (general case)

More generally, for a continuous distribution of charge confined to a volume ''V'', the corresponding expression for the dipole moment is:
$\mathbf(\mathbf) = \int_ \rho(\mathbf') \left(\mathbf' - \mathbf\right) d^3 \mathbf',$

where r locates the point of observation and ''d''³r′ denotes an elementary volume in ''V''. For an array of point charges, the charge density becomes a sum of Dirac delta functions:
$\rho(\mathbf) = \sum_^N \, q_i \, \delta \left(\mathbf - \mathbf_i\right),$

where each r_''i'' is a vector from some reference point to the charge ''q_i''. Substitution into the above integration formula provides:
$\mathbf(\mathbf) = \sum_^N \, q_i \int_V \delta\left(\mathbf_0 - \mathbf_i\right)\, \left(\mathbf_0 - \mathbf\right)\, d^3 \mathbf_0 = \sum_^N \, q_i \left(\mathbf_i - \mathbf\right).$

This expression is equivalent to the previous expression in the case of charge neutrality and ''N'' = 2. For two opposite charges, denoting the location of the positive charge of the pair as r₊ and the location of the negative charge as r₋:
$\mathbf(\mathbf) = q_1(\mathbf_1 - \mathbf) + q_2(\mathbf_2 - \mathbf) = q(\mathbf_+ -\mathbf)-q(\mathbf_- - \mathbf) = q (\mathbf_+ - \mathbf_-) = q\mathbf,$

showing that the dipole moment vector is directed from the negative charge to the positive charge because the position vector of a point is directed outward from the origin to that point.

The dipole moment is particularly useful in the context of an overall neutral system of charges, for example a pair of opposite charges, or a neutral conductor in a uniform electric field.
For such a system of charges, visualized as an array of paired opposite charges, the relation for electric dipole moment is:

\begin
\mathbf(\mathbf)
&= \sum_^N\, \int_V q_i \left delta \left(\mathbf_0 - \left(\mathbf_i + \mathbf_i\right)\right) - \delta\left(\mathbf_0 - \mathbf_i\right)\right, \left(\mathbf_0 - \mathbf\right)\ d^3 \mathbf_0 \\
&= \sum_^N\, q_i\, \left mathbf_i + \mathbf_i - \mathbf - \left(\mathbf_i - \mathbf\right)\right\\
&= \sum_^N q_i \mathbf_i = \sum_^ \mathbf_i \, ,
\end

where r is the point of observation, and d_''i'' = r_''i'' − r_''i'', r_''i'' being the position of the negative charge in the dipole ''i'', and r_''i'' the position of the positive charge.
This is the vector sum of the individual dipole moments of the neutral charge pairs. (Because of overall charge neutrality, the dipole moment is independent of the observer's position r.) Thus, the value of p is independent of the choice of reference point, provided the overall charge of the system is zero.

When discussing the dipole moment of a non-neutral system, such as the dipole moment of the proton, a dependence on the choice of reference point arises. In such cases it is conventional to choose the reference point to be the center of mass of the system, not some arbitrary origin. This choice is not only a matter of convention: the notion of dipole moment is essentially derived from the mechanical notion of torque, and as in mechanics, it is computationally and theoretically useful to choose the center of mass as the observation point. For a charged molecule the center of charge should be the reference point instead of the center of mass. For neutral systems the reference point is not important, and the dipole moment is an intrinsic property of the system.

Potential and field of an electric dipole

An ideal dipole consists of two opposite charges with infinitesimal separation. We compute the potential and field of such an ideal dipole starting with two opposite charges at separation ''d >'' 0, and taking the limit as ''d →'' 0.

Two closely spaced opposite charges ±''q'' have a potential of the form:
$\phi(\mathbf) \ =\ \frac \left( \frac - \frac \right) ,$
corresponding to the charge density
$\rho(\mathbf) \ =\ -\varepsilon_0\nabla^2\phi \ =\ q\delta\left(\mathbf - \mathbf_+\right) - q\delta\left(\mathbf - \mathbf_-\right)$
by Coulomb's law,
where the charge separation is:
$\mathbf = \mathbf_+ - \mathbf_- \, , \quad d = , \mathbf, \,.$

Let R denote the position vector relative to the midpoint $\frac$, and $\hat\mathbf$ the corresponding unit vector:
$\mathbf = \mathbf - \frac, \quad \hat = \frac\, ,$

Taylor expansion in $\tfrac dR$ (see multipole expansion and quadrupole) expresses this potential as a series.
$\phi(\mathbf) \ =\ \frac \frac + \mathcal O\left(\frac\right) \ \approx\ \frac \frac\, ,$
where higher order terms in the series are vanishing at large distances, ''R'', compared to ''d''. Here, the electric dipole moment p is, as above:
$\mathbf = q\mathbf\, .$

The result for the dipole potential also can be expressed as:
$\phi(\mathbf) \approx -\mathbf \cdot \mathbf \frac\, ,$

which relates the dipole potential to that of a point charge. A key point is that the potential of the dipole falls off faster with distance ''R'' than that of the point charge.

The electric field of the dipole is the negative gradient of the potential, leading to:
$\mathbf E\left(\mathbf R\right) = \frac\, .$

Thus, although two closely spaced opposite charges are ''not quite'' an ideal electric dipole (because their potential at short distances is not that of a dipole), at distances much larger than their separation, their dipole moment p appears directly in their potential and field.

As the two charges are brought closer together (''d'' is made smaller), the dipole term in the multipole expansion based on the ratio ''d''/''R'' becomes the only significant term at ever closer distances ''R'', and in the limit of infinitesimal separation the dipole term in this expansion is all that matters. As ''d'' is made infinitesimal, however, the dipole charge must be made to increase to hold p constant. This limiting process results in a "point dipole".

Dipole moment density and polarization density

The dipole moment of an array of charges,
$\mathbf p = \sum_^N q_i \mathbf \, ,$

determines the degree of polarity of the array, but for a neutral array it is simply a vector property of the array with no information about the array's absolute location. The dipole moment ''density'' of the array p(r) contains both the location of the array and its dipole moment. When it comes time to calculate the electric field in some region containing the array, Maxwell's equations are solved, and the information about the charge array is contained in the ''polarization density'' P(r) of Maxwell's equations. Depending upon how fine-grained an assessment of the electric field is required, more or less information about the charge array will have to be expressed by P(r). As explained below, sometimes it is sufficiently accurate to take P(r) = p(r). Sometimes a more detailed description is needed (for example, supplementing the dipole moment density with an additional quadrupole density) and sometimes even more elaborate versions of P(r) are necessary.

It now is explored just in what way the polarization density P(r) that enters Maxwell's equations is related to the dipole moment p of an overall neutral array of charges, and also to the ''dipole moment density'' p(r) (which describes not only the dipole moment, but also the array location). Only static situations are considered in what follows, so P(r) has no time dependence, and there is no displacement current. First is some discussion of the polarization density P(r). That discussion is followed with several particular examples.

A formulation of Maxwell's equations based upon division of charges and currents into "free" and "bound" charges and currents leads to introduction of the D- and P-fields:
$\mathbf = \varepsilon _0 \mathbf + \mathbf\, ,$
where P is called the polarization density. In this formulation, the divergence of this equation yields:
$\nabla \cdot \mathbf = \rho_f = \varepsilon _0 \nabla \cdot \mathbf +\nabla \cdot \mathbf\, ,$
and as the divergence term in E is the ''total'' charge, and ''ρ_f'' is "free charge", we are left with the relation:
$\nabla \cdot \mathbf = -\rho_b \, ,$
with ''ρ_b'' as the bound charge, by which is meant the difference between the total and the free charge densities.

As an aside, in the absence of magnetic effects, Maxwell's equations specify that
$\nabla \times \mathbf = \boldsymbol\, ,$

which implies
$\nabla \times \left( \mathbf - \mathbf \right) = \boldsymbol\, ,$

Applying Helmholtz decomposition:
$\mathbf - \mathbf = -\nabla \varphi \, ,$
for some scalar potential ''φ'', and:
$\nabla \cdot (\mathbf - \mathbf) = \varepsilon_0 \nabla \cdot \mathbf = \rho_f + \rho_b = - \nabla^2 \varphi\, .$

Suppose the charges are divided into free and bound, and the potential is divided into

$\varphi = \varphi_f + \varphi_b\, .$

Satisfaction of the boundary conditions upon ''φ'' may be divided arbitrarily between ''φ_f'' and ''φ_b'' because only the sum ''φ'' must satisfy these conditions. It follows that P is simply proportional to the electric field due to the charges selected as bound, with boundary conditions that prove convenient.
For example, one could place the boundary around the bound charges at infinity. Then ''φ_b'' falls off with distance from the bound charges. If an external field is present, and zero free charge, the field can be accounted for in the contribution of ''φ_f'', which would arrange to satisfy the boundary conditions and Laplace's equation $\nabla^2 \varphi_f = 0\, .$ In principle, one could add the same arbitrary ''curl'' to both D and P, which would cancel out of the difference D − P. However, assuming D and P originate in a simple division of charges into free and bound, they a formally similar to electric fields and so have zero ''curl''. In particular, when ''no'' free charge is present, one possible choice is P = ''ε''₀ E.

Next is discussed how several different dipole moment descriptions of a medium relate to the polarization entering Maxwell's equations.

Medium with charge and dipole densities

As described next, a model for polarization moment density p(r) results in a polarization
$\mathbf(\mathbf) = \mathbf(\mathbf)$
restricted to the same model. For a smoothly varying dipole moment distribution p(r), the corresponding bound charge density is simply
$\nabla \cdot \mathbf (\mathbf) = -\rho_b,$
as we will establish shortly via integration by parts. However, if p(r) exhibits an abrupt step in dipole moment at a boundary between two regions, ∇·p(r) results in a surface charge component of bound charge. This surface charge can be treated through a surface integral, or by using discontinuity conditions at the boundary, as illustrated in the various examples below.

As a first example relating dipole moment to polarization, consider a medium made up of a continuous charge density ''ρ''(r) and a continuous dipole moment distribution p(r). The potential at a position r is:
$\phi (\mathbf) = \frac \int \frac d^3 \mathbf_0 \ + \frac \int \frac d^3 \mathbf_0 ,$

where ''ρ''(r) is the unpaired charge density, and p(r) is the dipole moment density.For example, for a system of ideal dipoles with dipole moment p confined within some closed surface, the ''dipole density'' p(r) is equal to p inside the surface, but is zero outside. That is, the dipole density includes a Heaviside step function locating the dipoles inside the surface. Using an identity:
$\nabla_ \frac = \frac$
the polarization integral can be transformed:
$\begin \frac \int \frac d^3 \mathbf_0 = & \frac \int \mathbf \left(\mathbf_0\right) \cdot \nabla_ \frac d^3 \mathbf_0 , \\ = &\frac \int \nabla_ \cdot \left(\mathbf \left(\mathbf_0\right) \frac \right) d^3 \mathbf_0 - \frac \int \frac d^3 \mathbf_0 , \end$
where the vector identity $\nabla\cdot(\mathbf) = (\nabla\cdot\mathbf) + \mathbf\cdot(\nabla) \implies \mathbf\cdot(\nabla) = \nabla\cdot(\mathbf) - (\nabla\cdot\mathbf)$ was used in the last steps. The first term can be transformed to an integral over the surface bounding the volume of integration, and contributes a surface charge density, discussed later. Putting this result back into the potential, and ignoring the surface charge for now:
$\phi (\mathbf) = \frac \int \frac d^3 \mathbf_0\, ,$
where the volume integration extends only up to the bounding surface, and does not include this surface.

The potential is determined by the total charge, which the above shows consists of:
$\rho_\text \left(\mathbf_0\right) = \rho\left(\mathbf_0\right) - \nabla_ \cdot \mathbf \left(\mathbf_0\right)\, ,$
showing that:
$-\nabla_ \cdot \mathbf \left(\mathbf_0\right) = \rho_b\, .$

In short, the dipole moment density p(r) plays the role of the polarization density P for this medium. Notice, p(r) has a non-zero divergence equal to the bound charge density (as modeled in this approximation).

It may be noted that this approach can be extended to include all the multipoles: dipole, quadrupole, etc. Using the relation:
$\nabla \cdot \mathbf = \rho_f \, ,$

the polarization density is found to be:
$\mathbf(\mathbf) = \mathbf_\text - \nabla \cdot \mathbf_\text + \cdots\, ,$

where the added terms are meant to indicate contributions from higher multipoles. Evidently, inclusion of higher multipoles signifies that the polarization density P no longer is determined by a dipole moment density p alone. For example, in considering scattering from a charge array, different multipoles scatter an electromagnetic wave differently and independently, requiring a representation of the charges that goes beyond the dipole approximation.

Surface charge

Above, discussion was deferred for the first term in the expression for the potential due to the dipoles. Integrating the divergence results in a surface charge. The figure at the right provides an intuitive idea of why a surface charge arises. The figure shows a uniform array of identical dipoles between two surfaces. Internally, the heads and tails of dipoles are adjacent and cancel. At the bounding surfaces, however, no cancellation occurs. Instead, on one surface the dipole heads create a positive surface charge, while at the opposite surface the dipole tails create a negative surface charge. These two opposite surface charges create a net electric field in a direction opposite to the direction of the dipoles.

This idea is given mathematical form using the potential expression above. Ignoring the free charge, the potential is:
$\phi\left(\mathbf\right) = \frac \int \nabla_ \cdot \left(\mathbf \left(\mathbf_0\right) \frac \right) d^3 \mathbf_0 - \frac \int \frac d^3 \mathbf_0\, .$

Using the divergence theorem, the divergence term transforms into the surface integral:
$\frac \int \nabla_ \cdot \left(\mathbf \left(\mathbf_0\right) \frac\right) d^3\mathbf_0 = \frac \int \frac\left, \mathbf - \mathbf_0\ \, ,$

with dA₀ an element of surface area of the volume. In the event that p(r) is a constant, only the surface term survives:
$\phi(\mathbf) = \frac \int \frac\ \mathbf \cdot d\mathbf_0 \, ,$
with dA₀ an elementary area of the surface bounding the charges. In words, the potential due to a constant p inside the surface is equivalent to that of a ''surface charge''
$\sigma = \mathbf \cdot d \mathbf$
which is positive for surface elements with a component in the direction of p and negative for surface elements pointed oppositely. (Usually the direction of a surface element is taken to be that of the outward normal to the surface at the location of the element.)

If the bounding surface is a sphere, and the point of observation is at the center of this sphere, the integration over the surface of the sphere is zero: the positive and negative surface charge contributions to the potential cancel. If the point of observation is off-center, however, a net potential can result (depending upon the situation) because the positive and negative charges are at different distances from the point of observation. The field due to the surface charge is:
$\mathbf\left(\mathbf\right) = -\frac \nabla_\mathbf \int \frac\ \mathbf \cdot d\mathbf_0\, ,$
which, at the center of a spherical bounding surface is not zero (the ''fields'' of negative and positive charges on opposite sides of the center add because both fields point the same way) but is instead:
$\mathbf = -\frac\, .$

If we suppose the polarization of the dipoles was induced by an external field, the polarization field opposes the applied field and sometimes is called a ''depolarization field''. In the case when the polarization is ''outside'' a spherical cavity, the field in the cavity due to the surrounding dipoles is in the ''same'' direction as the polarization.

In particular, if the electric susceptibility is introduced through the approximation:
$\mathbf(\mathbf) = \varepsilon_0 \chi(\mathbf) \mathbf(\mathbf)\, ,$
where , in this case and in the following, represent the ''external field'' which induces the polarization.

Then:
$\nabla \cdot \mathbf(\mathbf) = \nabla \cdot \left(\chi(\mathbf) \varepsilon_0 \mathbf(\mathbf)\right) = -\rho_b\, .$

Whenever ''χ''(r) is used to model a step discontinuity at the boundary between two regions, the step produces a surface charge layer. For example, integrating along a normal to the bounding surface from a point just interior to one surface to another point just exterior:
\varepsilon_0 \hat \cdot \left chi\left(\mathbf_+\right) \mathbf\left(\mathbf_+\right) - \chi\left(\mathbf_-\right) \mathbf\left(\mathbf_-\right)\right= \frac \int d \Omega_n\ \rho_b = 0 \, ,

where ''A''_n, Ω_n indicate the area and volume of an elementary region straddling the boundary between the regions, and $\hat$ a unit normal to the surface. The right side vanishes as the volume shrinks, inasmuch as ρ_b is finite, indicating a discontinuity in ''E'', and therefore a surface charge. That is, where the modeled medium includes a step in permittivity, the polarization density corresponding to the dipole moment density
$\mathbf(\mathbf) = \chi(\mathbf) \mathbf(\mathbf)$

necessarily includes the contribution of a surface charge.

A physically more realistic modeling of p(r) would have the dipole moment density drop off rapidly, but smoothly to zero at the boundary of the confining region, rather than making a sudden step to zero density. Then the surface charge will not concentrate in an infinitely thin surface, but instead, being the divergence of a smoothly varying dipole moment density, will distribute itself throughout a thin, but finite transition layer.

Dielectric sphere in uniform external electric field

The above general remarks about surface charge are made more concrete by considering the example of a dielectric sphere in a uniform electric field.

The sphere is found to adopt a surface charge related to the dipole moment of its interior.

A uniform external electric field is supposed to point in the ''z''-direction, and spherical-polar coordinates are introduced so the potential created by this field is:
$\phi_\infty = -E_\infty z = -E_\infty r \cos\theta \, .$

The sphere is assumed to be described by a dielectric constant ''κ'', that is,
$\mathbf = \kappa \varepsilon_0 \mathbf \, ,$

and inside the sphere the potential satisfies Laplace's equation. Skipping a few details, the solution inside the sphere is:
$\phi_< = A r \cos\theta \, ,$

while outside the sphere:
$\phi_> = \left(Br + \frac \right) \cos\theta \, .$

At large distances, φ_> → φ_∞ so ''B'' = −''E_∞ ''. Continuity of potential and of the radial component of displacement ''D'' = κε₀''E'' determine the other two constants. Supposing the radius of the sphere is ''R'',
$A = -\frac E_\infty\ ;\ C = \frac E_\infty R^3\, ,$

As a consequence, the potential is:
$\phi_> = \left(-r + \frac \frac\right) E_\infty \cos\theta\, ,$
which is the potential due to applied field and, in addition, a dipole in the direction of the applied field (the ''z''-direction) of dipole moment:
$\mathbf = 4 \pi \varepsilon_0 \left(\frac R^3\right) \mathbf_\infty\, ,$

or, per unit volume:
$\frac = 3 \varepsilon_0 \left(\frac\right) \mathbf_\infty\, .$

The factor (''κ'' − 1)/(''κ'' + 2) is called the Clausius–Mossotti factor and shows that the induced polarization flips sign if ''κ'' < 1. Of course, this cannot happen in this example, but in an example with two different dielectrics ''κ'' is replaced by the ratio of the inner to outer region dielectric constants, which can be greater or smaller than one. The potential inside the sphere is:
$\phi_< = -\frac E_\infty r \cos\theta\, ,$

leading to the field inside the sphere:
$-\nabla \phi_< = \frac \mathbf_\infty = \left(1 - \frac\right)\mathbf_\infty\, ,$

showing the depolarizing effect of the dipole. Notice that the field inside the sphere is ''uniform'' and parallel to the applied field. The dipole moment is uniform throughout the interior of the sphere. The surface charge density on the sphere is the difference between the radial field components:
$\sigma = 3 \varepsilon_0 \frac E_\infty \cos\theta = \frac \mathbf \cdot \hat\, .$

This linear dielectric example shows that the dielectric constant treatment is equivalent to the uniform dipole moment model and leads to zero charge everywhere except for the surface charge at the boundary of the sphere.

General media

If observation is confined to regions sufficiently remote from a system of charges, a multipole expansion of the exact polarization density can be made. By truncating this expansion (for example, retaining only the dipole terms, or only the dipole and quadrupole terms, or ''etc.''), the results of the previous section are regained. In particular, truncating the expansion at the dipole term, the result is indistinguishable from the polarization density generated by a uniform dipole moment confined to the charge region. To the accuracy of this dipole approximation, as shown in the previous section, the dipole moment ''density'' p(r) (which includes not only p but the location of p) serves as P(r).

At locations ''inside'' the charge array, to connect an array of paired charges to an approximation involving only a dipole moment density p(r) requires additional considerations. The simplest approximation is to replace the charge array with a model of ideal (infinitesimally spaced) dipoles. In particular, as in the example above that uses a constant dipole moment density confined to a finite region, a surface charge and depolarization field results. A more general version of this model (which allows the polarization to vary with position) is the customary approach using electric susceptibility or electrical permittivity.

A more complex model of the point charge array introduces an effective medium by averaging the microscopic charges; for example, the averaging can arrange that only dipole fields play a role.

A related approach is to divide the charges into those nearby the point of observation, and those far enough away to allow a multipole expansion. The nearby charges then give rise to ''local field effects''.

In a common model of this type, the distant charges are treated as a homogeneous medium using a dielectric constant, and the nearby charges are treated only in a dipole approximation.
The approximation of a medium or an array of charges by only dipoles and their associated dipole moment density is sometimes called the ''point dipole'' approximation, the '' discrete dipole approximation'', or simply the ''dipole approximation''.

Electric dipole moments of fundamental particles

Not to be confused with spin which refers to the magnetic dipole moments of particles, much experimental work is continuing on measuring the electric dipole moments (EDM; or anomalous electric dipole moment) of fundamental and composite particles, namely those of the electron and neutron, respectively. As EDMs violate both the parity (P) and time-reversal (T) symmetries, their values yield a mostly model-independent measure of CP-violation in nature (assuming CPT symmetry is valid). Therefore, values for these EDMs place strong constraints upon the scale of CP-violation that extensions to the standard model of particle physics may allow. Current generations of experiments are designed to be sensitive to the supersymmetry range of EDMs, providing complementary experiments to those done at the LHC.

Indeed, many theories are inconsistent with the current limits and have effectively been ruled out, and established theory permits a much larger value than these limits, leading to the strong CP problem and prompting searches for new particles such as the axion.

We know at least in the Yukawa sector from neutral kaon oscillations that CP is broken. Experiments have been performed to measure the electric dipole moment of various particles like the electron and the neutron. Many models beyond the standard model with additional CP-violating terms generically predict a nonzero electric dipole moment and are hence sensitive to such new physics. Instanton corrections from a nonzero θ term in quantum chromodynamics predict a nonzero electric dipole moment for the neutron and proton, which have not been observed in experiments (where the best bounds come from analysing neutrons). This is the strong CP problem and is a prediction of chiral perturbation theory.

Dipole moments of molecules

Dipole moments in molecules are responsible for the behavior of a substance in the presence of external electric fields. The dipoles tend to be aligned to the external field which can be constant or time-dependent. This effect forms the basis of a modern experimental technique called dielectric spectroscopy.

Dipole moments can be found in common molecules such as water and also in biomolecules such as proteins.

By means of the total dipole moment of some material one can compute the dielectric constant which is related to the more intuitive concept of conductivity. If $\mathcal_$ is the total dipole moment of the sample, then the dielectric constant is given by,
$\varepsilon = 1 + k \left\langle \mathcal_\text^2 \right\rangle$
where ''k'' is a constant and $\left\langle \mathcal_\text^2 \right\rangle = \left\langle \mathcal_\text (t = 0) \mathcal_\text(t = 0) \right\rangle$ is the time correlation function of the total dipole moment. In general the total dipole moment have contributions coming
from translations and rotations of the molecules in the sample,
$\mathcal_\text = \mathcal_\text + \mathcal_\text.$

Therefore, the dielectric constant (and the conductivity) has contributions from both terms. This approach can be generalized to compute the frequency dependent dielectric function.

It is possible to calculate dipole moments from electronic structure theory, either as a response to constant electric fields or from the density matrix. Such values however are not directly comparable to experiment due to the potential presence of nuclear quantum effects, which can be substantial for even simple systems like the ammonia molecule. Coupled cluster theory (especially CCSD(T)) can give very accurate dipole moments, although it is possible to get reasonable estimates (within about 5%) from density functional theory, especially if hybrid or double hybrid functionals are employed. The dipole moment of a molecule can also be calculated based on the molecular structure using the concept of group contribution methods.

See also

*Anomalous magnetic dipole moment
*Bond dipole moment
*Neutron electric dipole moment
*Electron electric dipole moment
* Toroidal dipole moment
*Multipole expansion
*Multipole moments
*Solid harmonics
*Axial multipole moments
*Cylindrical multipole moments
*Spherical multipole moments
*Laplace expansion
*Legendre polynomials

Notes

References

Further reading

*

External links

Electric Dipole Moment – from Eric Weisstein's World of PhysicsElectrostatic Dipole Multiphysics Model

{{Authority control

Electric dipole moment
Electromagnetism