|
Telephone Signaling Interface
In telecommunications, an interface standard is a standard that describes one or more functional characteristics (such as code conversion, line assignments, or protocol compliance) or physical characteristics (such as electrical, mechanical, or optical characteristics) necessary to allow the exchange of information between two or more (usually different) systems or pieces of equipment. Communications protocols are an example. An interface standard may include operational characteristics and acceptable levels of performance. In the military community, interface standards permit command and control functions to be performed using communication and computer systems. Telephones There are many interface standards between analog telephone central office equipment and customer-premises equipment. Single voice paths generally include analog audio connections, either a two-wire circuit or four-wire circuit plus signaling paths to indicate call progress and status information, such as ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Telecommunication
Telecommunication is the transmission of information by various types of technologies over wire, radio, optical, or other electromagnetic systems. It has its origin in the desire of humans for communication over a distance greater than that feasible with the human voice, but with a similar scale of expediency; thus, slow systems (such as postal mail) are excluded from the field. The transmission media in telecommunication have evolved through numerous stages of technology, from beacons and other visual signals (such as smoke signals, semaphore telegraphs, signal flags, and optical heliographs), to electrical cable and electromagnetic radiation, including light. Such transmission paths are often divided into communication channels, which afford the advantages of multiplexing multiple concurrent communication sessions. ''Telecommunication'' is often used in its plural form. Other examples of pre-modern long-distance communication included audio messages, such as coded drumb ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Four-wire Circuit
In telecommunication, a four-wire circuit is a two-way circuit using two paths so arranged that the respective signals are transmitted in one direction only by one path and in the other direction by the other path. The four-wire circuit gets its name from the fact that is uses four conductors to create two complete electrical circuits, one for each direction. The two separate circuits (channels) allow full- duplex operation with low crosstalk. In telephony a four-wire circuit was historically used to transport and switch baseband audio signals in the phone company telephone exchange before the advent of digital modulation and the electronic switching system eliminated baseband audio from the telco plant except for the local loop. The local loop is a two-wire circuit for one reason only: to save copper. Using half the number of copper wire conductors per circuit means that the infrastructure cost for wiring each circuit is halved. Although a lower quality circuit, the local loop al ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Ground Start
{{refimprove, date=January 2008 In telephony, ground start is a method of signaling from a terminal of a subscriber local loop to a telephone exchange, where one side of a cable pair is temporarily grounded to request dial tone. Most middle 20th-century American payphones used coin-first ground start lines, with the starting ground connection provided by the coin itself, bridging a set of contacts as it passes through the coin chute. Ground start trunk Telephone companies typically provide two types of dial tone switched circuits – ground start and loop start. Private branch exchanges (PBX) work best on ground start trunks because those trunks can give them an on hook signal allowing for timely clearing. Normal single line telephones and key systems typically work on loop start lines. On loop start lines the PBX and central office may inadvertently seize the line simultaneously, a condition called ''glare'', resulting in call collision since neither gets the expected response ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Loop Start
Loop start is a telecommunications supervisory protocol between a central office or private branch exchange (PBX) and a subscriber telephone or other terminal for the purpose of starting and terminating a telephone call. It is the simplest of the telephone signaling systems, and uses the presence or absence of loop current to indicate the off-hook and on-hook loop states, respectively. It is used primarily for subscriber line signaling. An extension of the protocol that adds disconnect supervision is often called kewlstart. Protocol operation When the telephone is ''on-hook'', the potential of the ring conductor of the local loop is held at a nominal level of -48V DC with respect to the tip conductor, provided by the telephone exchange or a foreign exchange station (FXS) interface. When the terminal initiates use of the line, it causes current to flow by closing the loop, and this signals the exchange to provide dial tone on the line and to expect dial signals, in form of DTMF digi ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Kewlstart
Loop start is a telecommunications supervisory protocol between a central office or private branch exchange (PBX) and a subscriber telephone or other terminal for the purpose of starting and terminating a telephone call. It is the simplest of the telephone signaling systems, and uses the presence or absence of loop current to indicate the off-hook and on-hook loop states, respectively. It is used primarily for subscriber line signaling. An extension of the protocol that adds disconnect supervision is often called kewlstart. Protocol operation When the telephone is ''on-hook'', the potential of the ring conductor of the local loop is held at a nominal level of -48V DC with respect to the tip conductor, provided by the telephone exchange or a foreign exchange station (FXS) interface. When the terminal initiates use of the line, it causes current to flow by closing the loop, and this signals the exchange to provide dial tone on the line and to expect dial signals, in form of DTMF di ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
E And M Signaling
E and M signaling is a type of supervisory line signaling that uses DC signals on separate leads, called the "E" lead and "M" lead, traditionally used in the telecommunications industry between telephone switches. Various mnemonic names have been used to memorize these letters, such as ''Ear'' and ''Mouth'', the most common variation. E&M was originally developed for signaling between PABXs in different geographic locations over an analog private circuit. The protocol was later extended for use on digital carrier system with Channel Associated Signaling (CAS). Signaling units and trunk circuits The E&M standards were initially developed by Bell Labs and extended by national PTT administrations. The standard defines two sides of the interface, the trunk circuit and the signaling unit. The trunk circuit is normally the side to which the PABX is connected. The signaling unit is the special modem that converts the DC signaling protocol into tones that could be transmitted over a fo ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Dial Pulse
Pulse dialing is a signaling technology in telecommunications in which a direct current local loop circuit is interrupted according to a defined coding system for each signal transmitted, usually a digit. This lends the method the often used name loop disconnect dialing. In the most common variant of pulse dialing, decadic dialing, each of the ten Arabic numerals are encoded in a sequence of up to ten pulses. The most common version decodes the digits 1 through 9, as one to nine pulses, respectively, and the digit 0 as ten pulses. Historically, the most common device to produce such pulse trains is the rotary dial of the telephone, lending the technology another name, rotary dialing. The pulse repetition rate was historically determined based on the response time needed for electromechanical switching systems to operate reliably. Most telephone systems used the nominal rate of ten pulses per second, but operator dialing within and between central offices often used pulse rates up ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Foreign Exchange Station
Foreign exchange service (FX) is an access service in a telecommunications network in which a telephone in a given exchange area is connected, via a private line, as opposed to a switched line, to a telephone exchange or central office in another exchange area, called the ''foreign'' exchange, rather than the local exchange area where the subscriber station equipment is located. To call originators, it appears that the called party having the FX service is located in the foreign exchange area. It is assigned a telephone number of the foreign exchange. The telecommunication circuit between central offices that implements foreign exchange service has complementary interface types at each end. At the foreign central office that provides the service, the interface is called the foreign exchange office (FXO) end, and at the end where the subscriber station is connected, it provides the foreign exchange station (FXS) interface. Purpose Basic telephony terminology distinguishes two types ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Foreign Exchange Office
Foreign exchange service (FX) is an access service in a telecommunications network in which a telephone in a given exchange area is connected, via a private line, as opposed to a switched line, to a telephone exchange or central office in another exchange area, called the ''foreign'' exchange, rather than the local exchange area where the subscriber station equipment is located. To call originators, it appears that the called party having the FX service is located in the foreign exchange area. It is assigned a telephone number of the foreign exchange. The telecommunication circuit between central offices that implements foreign exchange service has complementary interface types at each end. At the foreign central office that provides the service, the interface is called the foreign exchange office (FXO) end, and at the end where the subscriber station is connected, it provides the foreign exchange station (FXS) interface. Purpose Basic telephony terminology distinguishes two types ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Answer Supervision
In telecommunication, supervision is the monitoring of a telecommunication circuit for telephony to convey to an operator, user, or a switching system, information about the operational state of the circuit. The typical operational states of trunks and lines are the idle and busy states, seizure, and disconnect. The states are indicated by various electrical signals and electrical conditions depending on the type of circuit, the type of terminating equipment, and the type of intended service. Answer and disconnect supervision are functions of line signaling that convey circuit seizure and disconnect. Answer supervision indicates that a call has been answered. Disconnect supervision provides a signal that the call has been disconnected. For example, the called party may indicate to the telephone exchange that the call is being disconnected by the called party by allowing loop current to flow in the line, or the called party indicates to the exchange that the call is being answered. ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Call Processing
In telecommunication, the term call processing has the following meanings: # The sequence of operations performed by a switching system from the acceptance of an incoming call through the final disposition of the call. See call control for a more complete description. # The series of steps and processes by which an organization automates the handling of telephone calls (usually incoming calls). Call processing in this sense may include the initial greeting of the call (perhaps time-of-day or other factor dependent) to routing the call based on dialed digits or lack thereof. The automated treatment may include routing the call to an Interactive Voice Response System (IVR), sending the call to a voice mail system, queuing the call, ''etc.'' or a combination of steps and real-time decisions. See also Automated attendant. # The end-to-end sequence of operations performed by a network from the instant a call attempt is initiated until the instant the call release is completed. # In ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Two-wire Circuit
In telecommunication, a two-wire circuit is characterized by supporting transmission in two directions simultaneously, as opposed to four-wire circuits, which have separate pairs for transmit and receive. The subscriber local loop from the telco central office are almost all two wire for analog baseband voice calls (and some digital services like ISDN), and converted to four-wire at the line card back when telephone switching was performed on baseband audio. Today the audio is digitized and processed completely in the digital domain upstream from the local loop. The reason for using two wires rather than four is simple economics—half the materials cost half as much to purchase and install. Note the use of the past-tense "cost," as installation of two-wire copper local loops for telephony was done primarily during the mid 20th century. In the first world there is no new infrastructure planning for new copper-based technology, and as customers are migrating to cellular telephony an ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
