|
Firing Order
The firing order of an internal combustion engine is the sequence of ignition for the cylinders. In a spark ignition (e.g. gasoline/petrol) engine, the firing order corresponds to the order in which the spark plugs are operated. In a diesel engine, the firing order corresponds to the order in which fuel is injected into each cylinder. Four-stroke engines must also time the valve openings relative to the firing order, as the valves do not open and close on every stroke. Firing order affects the vibration, sound and evenness of power output from the engine and heavily influences crankshaft design. Cylinder numbering Numbering systems for car engines The numbering system for cylinders is generally based on the cylinder numbers increasing from the front to the rear of an engine (See engine orientation below). However, there are differences between manufacturers in how this is applied; some commonly used systems are as listed below. ;Straight engine Cylinders numbered from front ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Straight-three Engine
A straight-three engine (also called an inline-triple or inline-three) is a three-cylinder piston engine where cylinders are arranged in a line along a common crankshaft. Less common than straight-four engines, straight-three engines have nonetheless been used in various motorcycles, cars and agricultural machinery. Design A crankshaft angle of 120 degrees is typically used by straight-three engines, since this results in an evenly spaced firing interval. Another benefit of this configuration is perfect primary balance and secondary balance, however an end-to-end rocking couple is induced because there is no symmetry in the piston velocities about the middle piston. A balance shaft is sometimes used to reduce the vibrations caused by the rocking couple. Other crankshaft angles have been used occasionally. The 1976-1981 Laverda Jota motorcycle used a 180 degree crankshaft, where the outer pistons rise and fall together and inner cylinder is offset from them by 180 degrees. ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Boeing-Stearman PT-13D (9)
Stearman Aircraft Corporation was an aircraft manufacturer in Wichita, Kansas. Although the company designed a range of other aircraft, it is most known for producing the Model 75, which is commonly known simply as the "Stearman" or "Boeing Stearman". History Lloyd Stearman established the Stearman Aircraft Corporation in 1927. Initially, the company was founded as Stearman Aircraft Corporation in October 1926 at Venice, California, where four C1 and C2 biplanes were built before production halted for financial reasons. On 27 September 1927, a new Stearman Aircraft Corporation was founded. The factory was then established in Wichita, Kansas, with financing of Walter Innes, where the new model Stearman C3 and Stearman 4 Speedmail were constructed. Two years later, he sold it to the United Aircraft and Transport Corporation. The Northrop Aircraft Corporation was merged into Stearman in July 1931. In September 1934, antitrust legislation forced United to separate its airline a ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Big-bang Firing Order
A big bang engine is an unconventional engine designed so that some of the power strokes occur simultaneously or in close succession. This is achieved by changing the ignition timing, changing or re-timing the camshaft, and sometimes in combination with a change in crankpin angle. The goal is to change the power delivery characteristics of the engine. A regular firing multi-cylinder engine fires at approximately even intervals, giving a smooth-running engine. Because a big-bang engine has uneven power delivery, they tend to run rougher and generate more vibration than an even-firing engine. Twin-cylinder engines Parallel twins The classic British parallel-twins ( BSA, Triumph, Norton, AJS & Matchless) all had 360° crankshafts that, compared to a single, gave twice as many ignition pulses which were evenly spaced. However, the 360 twin had a mechanical primary engine balance that was no better than a single. By contrast, Japanese parallel twins of the 1960s (such as the 196 ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
V12 Engine
A V12 engine is a twelve-cylinder piston engine where two banks of six cylinders are arranged in a V configuration around a common crankshaft. V12 engines are more common than V10 engines. However, they are less common than V8 engines. The first V12 engine was built in 1904 for use in racing boats. Due to the balanced nature of the engine and the smooth delivery of power, V12 engines were found in early luxury automobiles, boats, aircraft, and tanks. Aircraft V12 engines reached their apogee during World War II, following which they were mostly replaced by jet engines. In Formula One racing, V12 engines were common during the late 1960s and early 1990s. Applications of V12 engines in the 21st century have been as marine engines, in railway locomotives, as large stationary power as well as in some European sports and luxury cars. Design Balance and smoothness Each bank of a V12 engine essentially functions as a straight-six engine, which by itself has perfect primary and ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
V10 Engine
A V10 engine is a ten-cylinder piston engine where two banks of five cylinders are arranged in a V configuration around a common crankshaft. V10 engines are much less common than V8 and V12 engine A V12 engine is a twelve-cylinder piston engine where two banks of six cylinders are arranged in a V configuration around a common crankshaft. V12 engines are more common than V10 engines. However, they are less common than V8 engines. The f ...s. Several V10 diesel engines have been produced since 1965, and V10 petrol engines for road cars were first produced in 1991 with the release of the Dodge Viper. Design The V10 configuration does not have perfect engine balance, since an unbalanced couple (mechanics), rocking couple is caused by each cylinder bank functioning as a straight-five engine. Therefore, balance shafts are sometimes used to reduce the vibrations in a V10 engine. Diesel engines One of the first known V10 engines was used in the 1936 ''Busch-Sulzer ICRR ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
V8 Engine
A V8 engine is an eight-cylinder piston engine in which two banks of four cylinders share a common crankshaft and are arranged in a V configuration. The first V8 engine was produced by the French Antoinette company in 1904, developed and used in cars and speedboats but primarily aircraft; while the American 1914–1935 ''Cadillac L-Head'' engine is considered the first road going V8 engine to be mass produced in significant quantities. The popularity of V8 engines in cars was greatly increased following the 1932 introduction of the ''Ford Flathead V8''. In the early 21st century, use of V8 engines in passenger vehicles declined as automobile manufacturers opted for more fuel efficient, lower capacity engines, or hybrid and electric drivetrains. Design V-angle The majority of V8 engines use a V-angle (the angle between the two banks of cylinders) of 90 degrees. This angle results in good engine balance, which results in low vibrations; however, the downside is a larg ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Flat-six Engine
A flat-six engine, also known as a horizontally opposed-six, is a six-cylinder piston engine with three cylinders on each side of a central crankshaft. The most common type of flat-six engine is the boxer-six engine, where each pair of opposed cylinders moves inwards and outwards at the same time. The advantages of the flat-six layout are good engine balance (for reduced vibration), a low center of gravity, short length (compared with an inline-six engine) and being well suited to air-cooling. The disadvantages are a large width (which can limit the maximum steering angle when used in a front-engined car), a large intake manifold being required when a central carburetor is used, and duplication of the inlet and outlet connections for water-cooled engines. The first production flat-six engine was in the 1904 ''Wilson-Pilcher 18/24 HP'' car. The most notable use of flat-six engines is the Porsche 911 sports car, which has used flat-six engines continuously since 1963. Several o ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
V6 Engine
A V6 engine is a six-cylinder piston engine where the cylinders share a common crankshaft and are arranged in a V configuration. The first V6 engines were designed and produced independently by Marmon Motor Car Company, Deutz Gasmotoren Fabrik and Delahaye. Engines built after World War II include the Lancia V6 engine in 1950 for the Lancia Aurelia, and the Buick V6 engine in 1962 for the Buick Special. The V6 layout has become the most common layout for six-cylinder automotive engines. Design Due to their short length, V6 engines are often used as the larger engine option for vehicles which are otherwise produced with inline-four engines, especially in transverse engine vehicles. A downside for luxury cars is that V6 engines produce more vibrations than straight-six engines. Some sports cars use flat-six engines instead of V6 engines, due to their lower centre of gravity (which improves the handling). The displacement of modern V6 engines is typically between , though ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Straight-six Engine
The straight-six engine (also referred to as an inline-six engine; abbreviated I6 or L6) is a piston engine with six cylinders arranged in a straight line along the crankshaft. A straight-six engine has perfect primary and secondary engine balance, resulting in fewer vibrations than other designs of six or less cylinders. Until the mid-20th century, the straight-six layout was the most common design for engines with six cylinders. However, V6 engines became more common from the 1960s and by the 2000s most straight-six engines had been replaced by V6 engines. An exception to this trend is BMW which has produced automotive straight-six engines from 1933 to the present day. Characteristics In terms of packaging, straight-six engines are almost always narrower than a V6 engine or V8 engine, but longer than straight-four engines, V6s, and most V8s. Straight-six engines are typically produced in displacements ranging from , however engines ranging in size from the Benelli 750 ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Straight-five Engine
The straight-five engine (also referred to as an inline-five engine; abbreviated I5 or L5) is a piston engine with five cylinders mounted in a straight line along the crankshaft. Although less common than straight-four engines and straight-six engines, straight-five engines have occasionally been used by automobile manufacturers since the late 1930s, particularly the Mercedes Benz's diesel engines from 1974 to 2006 and Audi's petrol engines from 1979 to the present. Straight-five engines are smoother running than straight-four engines and shorter than straight-six engines. However, achieving consistent fuelling across all cylinders was problematic prior to the adoption of fuel injection. Characteristics Straight-five engines are typically shorter than straight-six engines, making them easier to fit transversely in an engine bay. They are also smoother than straight-four engines, and are narrower than V engines and flat engines. Engine balance and vibration Five-cylinder e ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Flat-four Engine
A flat-four engine, also known as a horizontally opposed-four engine, is a four-cylinder piston engine with two banks of cylinders lying on opposite sides of a common crankshaft. The most common type of flat-four engine is the boxer-four engine, each pair of opposed pistons moves inwards and outwards at the same time. A boxer-four engine has perfect primary and secondary balance, however, the two cylinder heads means the design is more expensive to produce than an inline-four engine. Boxer-four engines have been used in cars since 1897, especially by Volkswagen and Subaru. They have also occasionally been used in motorcycles and frequently in aircraft. Cessna and Piper use flat four engines from Lycoming and Continental in the most common civil aircraft in the world - the Cessna 172, and Piper Cherokee, while many ultralight and LSA planes use versions of the Rotax 912. Design Most flat-four engines are designed so that each pair of opposing pistons moves inwards and o ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
.jpg "Click for more on -> Firing Order")
