|
SCSI Status Code
A SCSI Status Code is used to determine the success or failure of a SCSI command. At the end of any command, the target returns a Status Code byte which should be one of the following: 00h Good This status code indicates that the device has completed the task successfully. 02h Check Condition When the target returns a Check Condition in response to a command it is indicating that it has entered a contingent allegiance condition. This means that an error occurred when it attempted to execute a SCSI command. The initiator usually then issues a SCSI Request Sense command in order to obtain a Key Code Qualifier ( KCQ) from the target. 04h Condition Met This status code is returned on successful completion of a Pre-fetch Command. 08h Busy The target returns Busy if it cannot complete a command at that time, for example if it is in the contingent allegiance condition. 10h Intermediate (obsolete) The target returns Intermediate when it successfully completes a linked command (ex ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
SCSI
Small Computer System Interface (SCSI, ) is a set of standards for physically connecting and transferring data between computers and peripheral devices. The SCSI standards define commands, protocols, electrical, optical and logical interfaces. The SCSI standard defines command sets for specific peripheral device types; the presence of "unknown" as one of these types means that in theory it can be used as an interface to almost any device, but the standard is highly pragmatic and addressed toward commercial requirements. The initial Parallel SCSI was most commonly used for hard disk drives and tape drives, but it can connect a wide range of other devices, including scanners and CD drives, although not all controllers can handle all devices. The ancestral SCSI standard, X3.131-1986, generally referred to as SCSI-1, was published by the X3T9 technical committee of the American National Standards Institute (ANSI) in 1986. SCSI-2 was published in August 1990 as X3.T9.2/86-109 ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
SCSI Command
In SCSI computer storage, computers and storage devices use a client-server model of communication. The computer is a client which requests the storage device to perform a service, e.g., to read or write data. The SCSI command architecture was originally defined for parallel SCSI buses but has been carried forward with minimal change for use with Fibre Channel, iSCSI, Serial Attached SCSI, and other transport layers. In the SCSI protocol, the initiator An initiator can refer to: * A person who instigates something. * Modulated neutron initiator, a neutron source used in some nuclear weapons ** Initiator, an Explosive booster ** Initiator, the first Nuclear chain reaction * Pyrotechnic initiato ... sends a SCSI command information unit to the target device. Data information units may then be transferred between the computer and device. Finally, the device sends a response information unit to the computer. SCSI commands are sent in a command descriptor block (CDB), which ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
SCSI Target
In computer data storage, a SCSI initiator is the endpoint that initiates a SCSI session, that is, sends a SCSI command. The initiator usually does not provide any Logical Unit Numbers (LUNs). On the other hand, a SCSI target is the endpoint that does ''not'' initiate sessions, but instead waits for initiators' commands and provides required input/output data transfers. The target usually provides to the initiators one or more LUNs, because otherwise no read or write command would be possible. Detailed information Typically, a computer is an initiator and a data storage device is a target. As in a client–server architecture, an initiator is analogous to the client, and a target is analogous to the server. Each SCSI address (each identifier on a SCSI bus) displays behavior of initiator, target, or (rarely) both at the same time. There is nothing in the SCSI protocol that prevents an initiator from acting as a target or vice versa. SCSI initiators are sometimes wrongly calle ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Byte
The byte is a unit of digital information that most commonly consists of eight bits. Historically, the byte was the number of bits used to encode a single character of text in a computer and for this reason it is the smallest addressable unit of memory in many computer architectures. To disambiguate arbitrarily sized bytes from the common 8-bit definition, network protocol documents such as The Internet Protocol () refer to an 8-bit byte as an octet. Those bits in an octet are usually counted with numbering from 0 to 7 or 7 to 0 depending on the bit endianness. The first bit is number 0, making the eighth bit number 7. The size of the byte has historically been hardware-dependent and no definitive standards existed that mandated the size. Sizes from 1 to 48 bits have been used. The six-bit character code was an often-used implementation in early encoding systems, and computers using six-bit and nine-bit bytes were common in the 1960s. These systems often had memory words ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
SCSI Contingent Allegiance Condition
On a computer SCSI connection, a contingent allegiance condition occurs while a SCSI device reports an error. SCSI communication takes place between an initiator and a target. The initiator sends a command to the target which then responds. At the end of the command the target returns a Status Code byte which is usually 00h for ''success'', 02h for a ''Check Condition'' (error), or 08h for ''busy''. When the target returns a Check Condition in response to a command, the initiator usually then issues a SCSI Request Sense command Small Computer System Interface (SCSI, ) is a set of standards for physically connecting and transferring data between computers and peripheral devices. The SCSI standards define commands, protocols, electrical, optical and logical interface ... in order to obtain more information. During the time between the reporting of a Check Condition and the issuing of the Request Sense command, the target is in the special state called the ''contingent all ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
SCSI Request Sense Command
Small Computer System Interface (SCSI, ) is a set of standards for physically connecting and transferring data between computers and peripheral devices. The SCSI standards define commands, protocols, electrical, optical and logical interfaces. The SCSI standard defines command sets for specific peripheral device types; the presence of "unknown" as one of these types means that in theory it can be used as an interface to almost any device, but the standard is highly pragmatic and addressed toward commercial requirements. The initial Parallel SCSI was most commonly used for hard disk drives and tape drives, but it can connect a wide range of other devices, including scanners and CD drives, although not all controllers can handle all devices. The ancestral SCSI standard, X3.131-1986, generally referred to as SCSI-1, was published by the X3T9 technical committee of the American National Standards Institute (ANSI) in 1986. SCSI-2 was published in August 1990 as X3.T9.2/86-10 ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
SCSI Pre-fetch Command
Small Computer System Interface (SCSI, ) is a set of standards for physically connecting and transferring data between computers and peripheral devices. The SCSI standards define commands, protocols, electrical, optical and logical interfaces. The SCSI standard defines command sets for specific peripheral device types; the presence of "unknown" as one of these types means that in theory it can be used as an interface to almost any device, but the standard is highly pragmatic and addressed toward commercial requirements. The initial Parallel SCSI was most commonly used for hard disk drives and tape drives, but it can connect a wide range of other devices, including scanners and CD drives, although not all controllers can handle all devices. The ancestral SCSI standard, X3.131-1986, generally referred to as SCSI-1, was published by the X3T9 technical committee of the American National Standards Institute (ANSI) in 1986. SCSI-2 was published in August 1990 as X3.T9.2/86-109, ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
SCSI Linked Command
Small Computer System Interface (SCSI, ) is a set of standards for physically connecting and transferring data between computers and peripheral devices. The SCSI standards define commands, protocols, electrical, optical and logical interfaces. The SCSI standard defines command sets for specific peripheral device types; the presence of "unknown" as one of these types means that in theory it can be used as an interface to almost any device, but the standard is highly pragmatic and addressed toward commercial requirements. The initial Parallel SCSI was most commonly used for hard disk drives and tape drives, but it can connect a wide range of other devices, including scanners and CD drives, although not all controllers can handle all devices. The ancestral SCSI standard, X3.131-1986, generally referred to as SCSI-1, was published by the X3T9 technical committee of the American National Standards Institute (ANSI) in 1986. SCSI-2 was published in August 1990 as X3.T9.2/86-109, ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Logical Unit Number
In computer storage, a logical unit number, or LUN, is a number used to identify a logical unit, which is a device addressed by the SCSI protocol or by Storage Area Network protocols that encapsulate SCSI, such as Fibre Channel or iSCSI. A LUN may be used with any device which supports read/write operations, such as a tape drive, but is most often used to refer to a logical disk as created on a SAN. Though not technically correct, the term "LUN" is often also used to refer to the logical disk itself. Examples To provide a practical example, a typical multi-disk drive has multiple physical SCSI ports, each with one SCSI target address assigned. An administrator may format the disk array as a RAID and then partition this RAID into several separate storage-volumes. To represent each volume, a SCSI target is configured to provide a logical unit. Each SCSI target may provide multiple logical units and thus represent multiple volumes, but this does ''not'' mean that those volumes are ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
SCSI Reserve Command
Small Computer System Interface (SCSI, ) is a set of standards for physically connecting and transferring data between computers and peripheral devices. The SCSI standards define commands, protocols, electrical, optical and logical interfaces. The SCSI standard defines command sets for specific peripheral device types; the presence of "unknown" as one of these types means that in theory it can be used as an interface to almost any device, but the standard is highly pragmatic and addressed toward commercial requirements. The initial Parallel SCSI was most commonly used for hard disk drives and tape drives, but it can connect a wide range of other devices, including scanners and CD drives, although not all controllers can handle all devices. The ancestral SCSI standard, X3.131-1986, generally referred to as SCSI-1, was published by the X3T9 technical committee of the American National Standards Institute (ANSI) in 1986. SCSI-2 was published in August 1990 as X3.T9.2/86-109, ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
SCSI Reserve Unit Command
Small Computer System Interface (SCSI, ) is a set of standards for physically connecting and transferring data between computers and peripheral devices. The SCSI standards define commands, protocols, electrical, optical and logical interfaces. The SCSI standard defines command sets for specific peripheral device types; the presence of "unknown" as one of these types means that in theory it can be used as an interface to almost any device, but the standard is highly pragmatic and addressed toward commercial requirements. The initial Parallel SCSI was most commonly used for hard disk drives and tape drives, but it can connect a wide range of other devices, including scanners and CD drives, although not all controllers can handle all devices. The ancestral SCSI standard, X3.131-1986, generally referred to as SCSI-1, was published by the X3T9 technical committee of the American National Standards Institute (ANSI) in 1986. SCSI-2 was published in August 1990 as X3.T9.2/86-109, ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
