|
Cisco Nexus Switches
The Cisco Nexus series switches are modular and fixed port network switches designed for the data center. Cisco Systems introduced the Nexus Series of switches on January 28, 2008. The first chassis in the Nexus 7000 family is a 10-slot chassis with two supervisor engine slots and eight I/O module slots at the front, as well as five crossbar switch fabric modules at the rear. Beside the Nexus 7000 there are also other models in the Nexus range. All switches in the Nexus range run the modular NX-OS firmware/operating system on the fabric. NX-OS has some high-availability features compared to the well-known Cisco IOS. This platform is optimized for high-density 10 Gigabit Ethernet. The Nexus switching range Cisco Nexus OS Software Defined Networking (SDN) allows the same policies that govern Identity and Access Management (IAM) to dictate levels of access to applications and data through a totally converged infrastructure not possible with legacy network and system access metho ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Network Switch
A network switch (also called switching hub, bridging hub, and, by the IEEE, MAC bridge) is networking hardware that connects devices on a computer network by using packet switching to receive and forward data to the destination device. A network switch is a multiport network bridge that uses MAC addresses to forward data at the data link layer (layer 2) of the OSI model. Some switches can also forward data at the network layer (layer 3) by additionally incorporating routing functionality. Such switches are commonly known as layer-3 switches or multilayer switches. Switches for Ethernet are the most common form of network switch. The first MAC Bridge was invented in 1983 by Mark Kempf, an engineer in the Networking Advanced Development group of Digital Equipment Corporation. The first 2 port Bridge product (LANBridge 100) was introduced by that company shortly after. The company subsequently produced multi-port switches for both Ethernet and Fiber Distributed Data Interface, F ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Command-line Interface
A command-line interpreter or command-line processor uses a command-line interface (CLI) to receive commands from a user in the form of lines of text. This provides a means of setting parameters for the environment, invoking executables and providing information to them as to what actions they are to perform. In some cases the invocation is conditional based on conditions established by the user or previous executables. Such access was first provided by computer terminals starting in the mid-1960s. This provided an interactive environment not available with punched cards or other input methods. Today, many users rely upon graphical user interfaces and menu-driven interactions. However, some programming and maintenance tasks may not have a graphical user interface and use a command line. Alternatives to the command-line interface include text-based user interface menus (for example, IBM AIX SMIT), keyboard shortcuts, and various desktop metaphors centered on the pointer ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Access Control List
In computer security, an access-control list (ACL) is a list of permissions associated with a system resource (object). An ACL specifies which users or system processes are granted access to objects, as well as what operations are allowed on given objects. Each entry in a typical ACL specifies a subject and an operation. For instance, if a file object has an ACL that contains , this would give Alice permission to read and write the file and give Bob permission only to read it. Implementations Many kinds of operating systems implement ACLs or have a historical implementation; the first implementation of ACLs was in the filesystem of Multics in 1965. Filesystem ACLs A filesystem ACL is a data structure (usually a table) containing entries that specify individual user or group rights to specific system objects such as programs, processes, or files. These entries are known as access-control entries (ACEs) in the Microsoft Windows NT, OpenVMS, and Unix-like operating system ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
VLAN
A virtual local area network (VLAN) is any broadcast domain that is partitioned and isolated in a computer network at the data link layer ( OSI layer 2).IEEE 802.1Q-2011, ''1.4 VLAN aims and benefits'' In this context, virtual, refers to a physical object recreated and altered by additional logic, within the local area network. VLANs work by applying tags to network frames and handling these tags in networking systems – creating the appearance and functionality of network traffic that is physically on a single network but acts as if it is split between separate networks. In this way, VLANs can keep network applications separate despite being connected to the same physical network, and without requiring multiple sets of cabling and networking devices to be deployed. VLANs allow network administrators to group hosts together even if the hosts are not directly connected to the same network switch. Because VLAN membership can be configured through software, this can greatly sim ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Multicast
In computer networking, multicast is group communication where data transmission is addressed to a group of destination computers simultaneously. Multicast can be one-to-many or many-to-many distribution. Multicast should not be confused with physical layer point-to-multipoint communication. Group communication may either be application layer multicast or network-assisted multicast, where the latter makes it possible for the source to efficiently send to the group in a single transmission. Copies are automatically created in other network elements, such as routers, switches and cellular network base stations, but only to network segments that currently contain members of the group. Network assisted multicast may be implemented at the data link layer using one-to-many addressing and switching such as Ethernet multicast addressing, Asynchronous Transfer Mode (ATM), point-to-multipoint virtual circuits (P2MP) or InfiniBand multicast. Network-assisted multicast may also be imp ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Border Gateway Protocol
Border Gateway Protocol (BGP) is a standardized exterior gateway protocol designed to exchange routing and reachability information among autonomous systems (AS) on the Internet. BGP is classified as a path-vector routing protocol, and it makes routing decisions based on paths, network policies, or rule-sets configured by a network administrator. BGP used for routing within an autonomous system is called Interior Border Gateway Protocol, Internal BGP (iBGP). In contrast, the Internet application of the protocol is called Exterior Border Gateway Protocol, External BGP (eBGP). History The Border Gateway Protocol was sketched out in 1989 by engineers on the back of "three ketchup-stained napkins", and is still known as the ''three-napkin protocol''. It was first described in 1989 in RFC 1105, and has been in use on the Internet since 1994. IPv6 BGP was first defined in in 1994, and it was improved to in 1998. The current version of BGP is version 4 (BGP4), which was publish ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Open Shortest Path First
Open Shortest Path First (OSPF) is a routing protocol for Internet Protocol (IP) networks. It uses a link state routing (LSR) algorithm and falls into the group of interior gateway protocols (IGPs), operating within a single autonomous system (AS). OSPF gathers link state information from available routers and constructs a topology map of the network. The topology is presented as a routing table to the Internet Layer for routing packets by their destination IP address. OSPF supports Internet Protocol Version 4 (IPv4) and Internet Protocol Version 6 (IPv6) networks and supports the Classless Inter-Domain Routing (CIDR) addressing model. OSPF is widely used in large enterprise networks. IS-IS, another LSR-based protocol, is more common in large service provider networks. Originally designed in the 1980s, OSPF is defined for IPv4 in protocol version 2 by RFC 2328 (1998)., Updated by RFC 5709, RFC 6549, RFC 6845, RFC 6860, RFC 7474, RFC 8042. The updates for IPv6 are specified ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Routing Information Protocol
The Routing Information Protocol (RIP) is one of the oldest distance-vector routing protocols which employs the hop count as a routing metric. RIP prevents routing loops by implementing a limit on the number of hops allowed in a path from source to destination. The largest number of hops allowed for RIP is 15, which limits the size of networks that RIP can support. RIP implements the split horizon, route poisoning, and holddown mechanisms to prevent incorrect routing information from being propagated. In RIPv1 routers broadcast updates with their routing table every 30 seconds. In the early deployments, routing tables were small enough that the traffic was not significant. As networks grew in size, however, it became evident there could be a massive traffic burst every 30 seconds, even if the routers had been initialized at random times. In most networking environments, RIP is not the preferred choice of routing protocol, as its time to converge and scalability are poor comp ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Multilayer Switch
A multilayer switch (MLS) is a computer networking device that switches on OSI layer 2 like an ordinary network switch and provides extra functions on higher OSI layers. The MLS was invented by engineers at Digital Equipment Corporation. Switching technologies are crucial to network design, as they allow traffic to be sent only where it is needed in most cases, using fast, hardware-based methods. Switching uses different kinds of network switches. A standard switch is known as a ''layer 2 switch'' and is commonly found in nearly any LAN. ''Layer 3'' or ''layer 4'' switches require advanced technology (see managed switch) and are more expensive and thus are usually only found in larger LANs or in special network environments. Multilayer switch Multi-layer switching combines layer 2, 3 and 4 switching technologies and provides high-speed scalability with low latency. Multi-layer switching can move traffic at wire speed and also provide layer 3 routing. There is no performance d ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Colocation Centre
A colocation center (also spelled co-location, or colo) or "carrier hotel", is a type of data centre where equipment, space, and bandwidth are available for rental to retail customers. Colocation facilities provide space, power, cooling, and physical security for the server, storage, and networking equipment of other firms and also connect them to a variety of telecommunications and network service providers with a minimum of cost and complexity. Configuration Many colocation providers sell to a wide range of customers, ranging from large enterprises to small companies. Typically, the customer owns the information technology (IT) equipment and the facility provides power and cooling. Customers retain control over the design and usage of their equipment, but daily management of the data center and facility are overseen by the multi-tenant colocation provider. * Cabinets – A cabinet is a locking unit that holds a server rack. In a multi-tenant data center, servers within cab ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Fibre Channel Over Ethernet
Fibre Channel over Ethernet (FCoE) is a computer network technology that encapsulates Fibre Channel frames over Ethernet networks. This allows Fibre Channel to use 10 Gigabit Ethernet networks (or higher speeds) while preserving the Fibre Channel protocol. The specification was part of the International Committee for Information Technology Standards T11 FC-BB-5 standard published in 2009. Functionality FCoE transports Fibre Channel directly over Ethernet while being independent of the Ethernet forwarding scheme. The FCoE protocol specification replaces the FC0 and FC1 layers of the Fibre Channel stack with Ethernet. By retaining the native Fibre Channel constructs, FCoE was meant to integrate with existing Fibre Channel networks and management software. Data centers used Ethernet for TCP/IP networks and Fibre Channel for storage area networks (SANs). With FCoE, Fibre Channel becomes another network protocol running on Ethernet, alongside traditional Internet Protocol (IP) t ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Dell M1000e
The Dell blade server products are built around their M1000e enclosure that can hold their server blades, an embedded EqualLogic iSCSI storage area network and I/O modules including Ethernet, Fibre Channel and InfiniBand switches. Enclosure The M1000e fits in a 19-inch rack and is 10 rack units high (44 cm), 17.6" (44.7 cm) wide and 29.7" (75.4 cm) deep. The empty blade enclosure weighs 44.5 kg while a fully loaded system can weigh up to 178.8 kg.Dell websitTech specs for the M1000e visited 10 March 2013 On the front the servers are inserted while at the backside the power-supplies, fans and I/O modules are inserted together with the management modules(s) (CMC or chassis management controller) and the KVM switch. A blade enclosure offers centralized management for the servers and I/O systems of the blade-system. Most servers used in the blade-system offer an iDRAC card and one can connect to each servers iDRAC via the M1000e management system. It is also ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
.jpg "Click for more on -> Cisco Nexus Switches")
