Printed circuit boardA printed circuit board (PCB), also known as a printed wiring board (PWB), is a laminated sandwich structure of conductive and insulating layers, each with a pattern of traces, planes and other features (similar to wires on a flat surface) etched from one or more sheet layers of copper laminated onto or between sheet layers of a non-conductive substrate. PCBs are used to connect or "wire" components to one another in an electronic circuit.
Point-to-point constructionIn electronics, point-to-point construction is a non-automated technique for constructing circuits which was widely used before the use of printed circuit boards (PCBs) and automated assembly gradually became widespread following their introduction in the 1950s. Circuits using thermionic valves (vacuum tubes) were relatively large, relatively simple (the number of large, hot, expensive devices which needed replacing was minimised), and used large sockets, all of which made the PCB less obviously advantageous than with later complex semiconductor circuits.
Dual in-line packageIn microelectronics, a dual in-line package (DIP or DIL) is an electronic component package with a rectangular housing and two parallel rows of electrical connecting pins. The package may be through-hole mounted to a printed circuit board (PCB) or inserted in a socket.
Electronic circuitAn electronic circuit is composed of individual electronic components, such as resistors, transistors, capacitors, inductors and diodes, connected by conductive wires or traces through which electric current can flow. It is a type of electrical circuit. For a circuit to be referred to as electronic, rather than electrical, generally at least one active component must be present.StripboardStripboard is the generic name for a widely used type of electronicsprototyping material for circuit boards characterized by a pre-formed 0.1 inches (2.54 mm) regular (rectangular) grid of holes, with wide parallel strips of copper cladding running in one direction all the way along one side of an insulating bonded paper board.
Integrated circuitElectronic circuit formed on a small, flat piece of semiconductor materialA microscope image of an integrated circuit die used to control LCDs. The pinouts are the dark circles surrounding the integrated circuit.An integrated circuit (IC), also known as a microchip or simply chip, is a compact assembly of electronic circuits formed from various electronic components, such as transistors, resistors, and capacitors, and their interconnections.
PerfboardPerfboard is a material for prototypingelectronic circuits. It is a thin, rigid sheet with holes pre-drilled at standard intervals across a grid, usually a square grid of 0.1 inches (2.54 mm) spacing. These holes are ringed by round or square copper pads, though bare boards are also available. Inexpensive perfboard may have pads on only one side of the board, while better quality perfboard can have pads on both sides (plate-through holes).
ResistorA resistor is a passivetwo-terminalelectronic component that implements electrical resistance as a circuit element. In electronic circuits, resistors are used to reduce current flow, adjust signal levels, to divide voltages, bias active elements, and terminate transmission lines, among other uses. High-power resistors that can dissipate many watts of electrical power as heat may be used as part of motor controls, in power distribution systems, or as test loads for generators.
Cutting boardA cutting board (or chopping board) is a durable flat surface on which to place material for cutting. The kitchen cutting board is commonly used in food preparation with knives; other types exist for cutting raw materials such as leather, rubber or plastic. Kitchen cutting boards are often made of a plank of hardwood or polyethylene, and come in various widths and sizes.
Electronics prototypingIn electronics, prototyping means building an actual circuit to a theoretical design to verify that it works, and to provide a physical platform for debugging it if it does not. The prototype is often constructed using techniques such as wire wrapping or using a breadboard, stripboard or perfboard, with the result being a circuit that is electrically identical to the design but not physically identical to the final product.
Parasitic capacitanceParasitic capacitance or stray capacitance is the unavoidable and usually unwanted capacitance that exists between the parts of an electronic component or circuit simply because of their proximity to each other. When two electrical conductors at different voltages are close together, the electric field between them causes electric charge to be stored on them; this effect is capacitance.
SolderingSoldering (US: ; UK: ) joins two metal surfaces using a filler metal called solder. The surfaces are heated, melting the solder, which is then allowed to cool and solidify, creating a strong and durable joint. Soldering is commonly used in the electronics industry for the manufacture and repair of printed circuit boards (PCBs) and other electronic components. It is also used in plumbing and metalwork, as well as in the manufacture of jewelry and other decorative items.
Central processing unitCentral computer component that executes instructionsCore i9-14900KF, a 2023 CPU made by IntelInside a central processing unit: The integrated circuit of Intel's Xeon 3060, first manufactured in 2006A central processing unit (CPU), also known as a central processor, main processor, or simply processor, is the primary processor in a given computer.*As an Amazon Associate I earn from qualifying purchases.