|
SCSI Peripheral Device Type
A SCSI Peripheral Device Type describes the capabilities provided by a SCSI device. It is a five-bit field in the first byte returned in response to an INQUIRY SCSI command.Draft of SCSI Primary Commands - 4 (SPC-4 r36d), section 6.6.2 - Standard INQUIRY data Defined values are: References SCSI {{compu-hardware-stub ...[...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
SCSI
Small Computer System Interface (SCSI, ) is a set of standards for physically connecting and transferring data between computers and peripheral devices. The SCSI standards define commands, protocols, electrical, optical and logical interfaces. The SCSI standard defines command sets for specific peripheral device types; the presence of "unknown" as one of these types means that in theory it can be used as an interface to almost any device, but the standard is highly pragmatic and addressed toward commercial requirements. The initial Parallel SCSI was most commonly used for hard disk drives and tape drives, but it can connect a wide range of other devices, including scanners and CD drives, although not all controllers can handle all devices. The ancestral SCSI standard, X3.131-1986, generally referred to as SCSI-1, was published by the X3T9 technical committee of the American National Standards Institute (ANSI) in 1986. SCSI-2 was published in August 1990 as X3.T9.2/86-109 ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
SCSI Command
In SCSI computer storage, computers and storage devices use a client-server model of communication. The computer is a client which requests the storage device to perform a service, e.g., to read or write data. The SCSI command architecture was originally defined for parallel SCSI buses but has been carried forward with minimal change for use with Fibre Channel, iSCSI, Serial Attached SCSI, and other transport layers. In the SCSI protocol, the initiator sends a SCSI command information unit to the target device. Data information units may then be transferred between the computer and device. Finally, the device sends a response information unit to the computer. SCSI commands are sent in a command descriptor block In SCSI standards for transferring data between computers and peripheral devices, often computer storage, commands are sent in a Command Descriptor Block (CDB). Each CDB can be a total of 6, 10, 12, or 16 bytes, but later versions of the SCSI sta ... (CDB), whi ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
MultiMedia Commands
SCSI Multimedia Commands (MMC) defines a SCSI/ATAPI based command set for accessing and controlling devices of type 05h. Such devices read or write optical media: CD, DVD, BD. T10 subcommittee is responsible for developing MMC as well as other SCSI command set standards. It was approved in December 1997 by ANSI.http://www.13thmonkey.org/documentation/SCSI/x3_304_1997.pdf (MMC-3) See also *Mount Rainier Mount Rainier (), indigenously known as Tahoma, Tacoma, Tacobet, or təqʷubəʔ, is a large active stratovolcano in the Cascade Range of the Pacific Northwest, located in Mount Rainier National Park about south-southeast of Seattle. With a ... (MRW) * Layer Jump Recording (LJR) * Optical disc recording modes * Small Form Factor committee (SFF) References SCSI {{tech-stub ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
SCSI Enclosure Services
SCSI Enclosure Services (SES) is a protocol for more modern SCSI enclosure products. An initiator can communicate with the enclosure using a specialized set of SCSI commands to access power, cooling, and other non-data characteristics. SES devices There are two major classes of SES devices: * Attached enclosure services devices allow SES communication through a logical unit within one SCSI disk drive located in the enclosure. The disk-drive then communicates with the enclosure by some other method, the only commonly used one being Enclosure Services Interface (ESI). In fault-tolerant enclosures, more than one disk-drive slot has ESI enabled to allow SES communications to continue even after the failure of any of the disk-drives. The definition of the ESI protocols is owned by an ANSI committee and defined in their specifications ANSI SFF-8067 and SFF-8045. * Standalone enclosure services enclosures have a separate SES processor which occupies its own address on the SCSI bus. ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
