|
Birdsmouth Joint
In light frame construction, a birdsmouth joint or bird's beak cut is a woodworking joint that is generally used to connect a roof rafter to the top plate A plate or wall plate is a horizontal, structural, load-bearing member in wooden building framing. Timber framing A plate in timber framing is "A piece of Timber upon which some considerable weight is framed...Hence Ground-Plate...Window-plat ... of a supporting wall. It is an indentation cut into the rafter which consists of a "seat cut" (the face of which rests on the top plate) and a "heel cut" or "plumb cut" (the face of which lies parallel to the supporting wall), forming a shape resembling a bird's mouth. The indentation should not extend unsupported on the interior in order to maintain the structural integrity of the rafter because the unsupported section can split along the grain of the wood. The joint is generally fastened with nails by toenailing the rafter from the side into the top plate below. The depth of a ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Light Frame Construction
Framing, in construction, is the fitting together of pieces to give a structure, particularly a building, support and shape. Framing materials are usually wood, engineered wood, or structural steel. The alternative to framed construction is generally called ''mass wall'' construction, where horizontal layers of stacked materials such as log building, masonry, rammed earth, adobe, etc. are used without framing. Building framing is divided into two broad categories, heavy-frame construction (heavy framing) if the vertical supports are few and heavy such as in timber framing, pole building framing, or steel framing; or light-frame construction (light-framing) if the supports are more numerous and smaller, such as balloon, platform, light-steel framing and pre-built framing. Light-frame construction using standardized dimensional lumber has become the dominant construction method in North America and Australia due to the economy of the method; use of minimal structural materia ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Woodworking Joints
Joinery is a part of woodworking that involves joining pieces of wood, engineered lumber, or synthetic substitutes (such as laminate), to produce more complex items. Some woodworking joints employ mechanical fasteners, bindings, or adhesives, while others use only wood elements (such as dowels or plain mortise and tenon fittings). The characteristics of wooden joints—strength, flexibility, toughness, appearance, etc.—derive from the properties of the materials involved and the purpose of the joint. Therefore, different joinery techniques are used to meet differing requirements. For example, the joinery used to construct a house can be different from that used to make cabinetry or furniture, although some concepts overlap. In British English joinery is distinguished from carpentry, which is considered to be a form of structural timber work; in other locales joinery is considered a form of carpentry. History Many traditional wood joinery techniques use the distinctive mate ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Rafter
A rafter is one of a series of sloped structural members such as Beam (structure), steel beams that extend from the ridge or hip to the wall plate, downslope perimeter or eave, and that are designed to support the roof Roof shingle, shingles, roof deck, roof covering and its associated loads. A pair of rafters is called a ''couple''. In home construction, rafters are normally made of wood. Exposed rafters are a feature of some traditional roof styles. Applications In recent buildings there is a preference for trussed rafters on the grounds of cost, economy of materials, off-site manufacture, and ease of construction, as well as design considerations including span limitations and roof loads (weight from above). Types in traditional timber framing There are many names for rafters depending on their location, shape, or size (see below). The earliest surviving roofs in Europe are of common rafters on a tie beam; this assembly is known as a "closed couple". Later, principal raf ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Top Plate
A plate or wall plate is a horizontal, structural, load-bearing member in wooden building framing. Timber framing A plate in timber framing is "A piece of Timber upon which some considerable weight is framed...Hence Ground-Plate...Window-plate [obsolete]..." etc. Also called a wall plate, raising plate,Sturgis, Russell. ''Sturgis' illustrated dictionary of architecture and building: an unabridged reprint of the 1901-2 edition''. 1901. Reprint. Mineola, N.Y.: Dover, 1989. 159. Print. or top plate,Sherwood, Gerald E., and Robert C. Stroh. ''Wood-frame house construction''. Washington, D.C.: U.S. Dept. of Agriculture, Forest Service :, 1989. 54. Print. An exception to the use of the term plate for a large, load-bearing timber in a wall is the bressummer, a timber supporting a wall over a wall opening (see also: Lintel (architecture), lintel). These are common in Australia. The terms sole plate or sill plate are used for the members at the bottom of a wall at the foundation but ar ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Toenailing
Toenailing or skew-nailing is a viable, structurally sound method of the driving of a nail at a roughly 30° angle to fasten two pieces of wood together, typically with their grains perpendicular. The term comes colloquially from fastening wood at the bottom, or toe, of the board. A variation of toenailing is to use screws, casually known as "toe-screwing". Toenails are typically driven in opposing pairs when possible, or pairs of pairs when appropriate. The angled nailing makes later dismantling difficult or destructive. History The word toenailing has been used in carpentry since at least 1949. Common applications *Fastening a wall stud to a sole plate in stud framing. *Used in place of end nailing when fastening locations are not easily accessible, like installing blocking between studs and joists. *Attaching a rafter to the top plate of a wall at its birdsmouth. *Commonly used with screws in carpentry to quickly secure temporary framing or work aids such as a jig. *Can be us ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Building Engineering
Architectural engineering or architecture engineering, also known as building engineering, is a Academic discipline, discipline that deals with the engineering and construction of buildings, such as environmental, structural, mechanical, electrical, computational, embeddable, and other research domains. It is related to Architecture, Mechatronics Engineering, Computer engineering, Computer Engineering, Aerospace engineering, Aerospace Engineering, and civil engineering, Civil Engineering, but distinguished from Interior design, Interior Design and architectural design, Architectural Design as an art and science of designing infrastructure through these various engineering disciplines, from which properly align with many related surrounding engineering advancements. From reduction of greenhouse gas emissions to the construction of resilient buildings, architectural engineers are at the forefront of addressing several major challenges of the 21st century. They apply the latest scie ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Woodworking
Woodworking is the skill of making items from wood, and includes cabinetry, furniture making, wood carving, joinery, carpentry, and woodturning. History Along with stone, clay and animal parts, wood was one of the first materials worked by early humans. Microwear analysis of the Mousterian stone tools used by the Neanderthals show that many were used to work wood. The development of civilization was closely tied to the development of increasingly greater degrees of skill in working these materials. Among the earlliest finds of woodworking are shaped sticks displaying notches from Kalambo Falls in southen Africa, dating to around 476,000 years ago. The Clacton spearhead from Clacton-on-Sea, England, dating to around 400,000 years ago,Allington-Jones, L., (2015) ''Archaeological Journal'', 172 (2) 273–296 The Clacton Spear – The Last One Hundred Years the Schöningen spears, from Schöningen (Germany) dating around 300,000 years ago and the Lehringen spear from no ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Structural System
The term structural system or structural frame in structural engineering refers to the load-resisting sub-system of a building or object. The structural system transfers loads through interconnected elements or members. Commonly used structures can be classified into five major categories, depending on the type of primary stress that may arise in the members of the structures under major design loads. However any two or more of the basic structural types described in the following may be combined in a single structure, such as a building or a bridge in order to meet the structure's functional requirements.Kassimali, A. (1999). ''Structural analysis''. 2nd edition. Pacific Grove, C.A.: PWS Publication. * Tensile structures: Members of tensile structures are subject to pure tension under the action of external loads. Because the tensile stress is uniformly distributed over the cross-sectional area of members, the material of such a structure is utilized in the most efficient ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
