|
Backsaw
A backsaw is any hand saw which has a stiffening rib on the edge opposite the cutting edge, enabling better control and more precise cutting than with other types of saws. Backsaws are normally used in woodworking for precise work, such as cutting dovetails, mitres, or tenons in cabinetry and joinery. Because of the stiffening rib, backsaws are limited in the depth to which they can cut. Backsaws usually have relatively closely spaced teeth, often with little or no set. Types of backsaws Backsaws include the tenon saw, the dovetail saw, and the (United Kingdom) sash saw 1. Tenon and dovetail saws usually have a pistol grip style handle which may be open or closed at the bottom. Different types of backsaw include: * Mitre saw – often referred to as a large backsaw (20–30 inches or 60–90 cm) used either in a wooden or metal mitre box or in a metal frame which allowed cutting mitres of any specified angle. Note that not all mitre saws are backsaws, and the electr ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Mitre Box
A mitre box or miter box (American English) is a wood working appliance used to guide a hand saw for making precise cuts, usually 45° mitre cuts. Traditional mitre boxes are simple in construction and made of wood, while adjustable mitre boxes are made of metal and can be adjusted for cutting any angle from 45° to 90°. In many workshops and jobsites mitre boxes have been superseded by the powered mitre saw, however advocates for mitre boxes argue that they are more accurate, safer, quieter, cheaper, and take up less space than a powered mitre saw. Description Basic mitre box The most common and simplest form of a mitre box is a U-shaped block made from wood, plastic or aluminium, which is open at the top and the ends. The box is made wide enough to accommodate the width of the workpieces to be cut. Slots are cut in the walls of the box at the precise angle at which the cut is to be made. These slots provide the guide for the saw to follow. Most commonly, the slots in t ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Japanese Saw
The Japanese saw or is a type of saw used in woodworking and Japanese carpentry that cuts on the pull stroke, unlike most European saws that cut on the push stroke. Japanese saws are the best known pull saws, but they are also used in China, Iran, Iraq, Korea, Nepal, and Turkey. Among European saws, both coping saws for woodworking and jeweler's saws for metal working also cut on the pull stroke like Japanese saws. Cutting on the pull stroke is claimed to cut more efficiently and leave a narrower cut width (wikt:kerf, kerf). On the other hand, a pull stroke does not easily permit putting one's body weight behind a stroke. This can be readily solved by using a vice or clamping. Another disadvantage, due to the arrangement and form of the teeth, is that Japanese saws do not work as well on hardwoods as European saws do. Japanese saws were originally intended for comparatively soft woods like cypress and pine whereas European saws were intended for hard woods like oak and maple. Th ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Bench Hook
A bench hook is a Workbench (woodworking), workbench appliance used in woodworking to hold a workpiece in place while Cross-cutting, crosscutting with a hand saw. A bench hook is a simple method used to improve accuracy and safety. Construction Bench hooks are simple in construction and though they can be purchased, they are typically made by the woodworker from offcuts and scraps of timber or sheet goods (such as plywood). The most common type of bench hook is made from three pieces of wood joined together: * The ''bed'', being anywhere from wide and long depending on preference. The workpiece sits atop the bed, and the bed protects the workbench from the saw. * The first stop, also called the Fence (woodworking), fence, is fixed across the top of the bed. Usually this stop doesn't span the full width of the bed, so that the end of the stop can be used as a guide while sawing. This way the saw cuts into the bench hook and not the workbench. * The other stop, or the ''hook'' ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Musical Instrument
A musical instrument is a device created or adapted to make Music, musical sounds. In principle, any object that produces sound can be considered a musical instrument—it is through purpose that the object becomes a musical instrument. A person who plays a musical instrument is known as an ''#Instrumentalist, instrumentalist''. The history of musical instruments dates to the beginnings of human culture. Early musical instruments may have been used for rituals, such as a horn (music), horn to signal success on the hunt, or a drum in a religious ceremony. Cultures eventually developed composition and performance of melody, melodies for entertainment. Musical instruments evolved in step with changing applications and technologies. The exact date and specific origin of the first device considered a musical instrument, is widely disputed. The oldest object identified by scholars as a musical instrument, is Divje Babe flute, a simple flute, dated back 50,000–60,000 years. Many scho ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Marking Knife
A marking knife or striking knife is a woodworking layout tool used for accurately marking workpieces. It is used to cut a visible line, which can then be used to guide a hand saw, chisel or plane when making woodworking joints and other operations. They are generally used when marking across the grain of the wood, with scratch awls better suited for marking with the grain. Description The blades on marking knives are made of tool steel, have either a skewed end or a spear point, and the knife edge is bevelled on either one side of the blade or both sides. On single-bevel skewed knives the side of the blade that is bevelled dictates whether the knife is for left-handed or right-handed use, while single-bevel spear point knives are suited to both. Some marking knives incorporate a marking knife blade at one end, and a scratch awl tip at the other end – but because of this they are sometimes considered dangerous to use. Marking knives are either made from a single piece ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Spot Welding
Spot welding (or resistance spot welding) is a type of electric resistance welding used to weld various sheet metal products, through a process in which contacting metal surface points are joined by the heat obtained from resistance to electric current. The process uses two shaped copper alloy electrodes to concentrate welding current into a small "spot" and to simultaneously clamp the sheets together. Work-pieces are held together under pressure exerted by electrodes. Typically the sheets are in the thickness range. Forcing a large current through the spot will melt the metal and form the weld. The attractive feature of spot welding is that a large amount of energy can be delivered to the spot in a very short time (approximately 10–100 milliseconds). This permits the welding to occur without excessive heating of the remainder of the sheet. The amount of heat (energy) delivered to the spot is determined by the resistance between the electrodes and the magnitude and duration ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Swage
Swaging () is a forging process in which the dimensions of an item are altered using dies into which the item is forced. Swaging is usually a cold working process, but also may be hot worked. The term swage may apply to the process (verb) or to a die or tool (noun) used in that process. Origin The term "swage" comes from the Old French term , meaning "decorative groove" or "ornamental moulding". Swages were originally tools used by blacksmiths to form metal into various shapes too intricate to make with a hammer alone. These have handles for holding or pegs for attaching to an anvil, and often a flat head for striking with a hammer. Swage blocks are anvil-like dies with various shapes forged into them, which are also used for forming metal. Swages called " fullers" are specific to making grooves in swords and knives. ''Swage'' is most often pronounced ( AHD format: swāj). Another (less common) pronunciation sometimes heard in the metalworking industries is (AHD forma ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Balsa
''Ochroma pyramidale'', commonly known as balsa, is a large, fast-growing tree native to the Americas. It is the sole member of the genus ''Ochroma'', and is classified in the subfamily Bombacoideae of the mallow family Malvaceae. The tree is famous for its wide usage in woodworking, due to its softness and its high strength compared to its low density. The name ''balsa'' is the Spanish word for "raft" and the Portuguese word for ferry. A deciduous angiosperm, ''Ochroma pyramidale'' can grow up to 30 m tall, and is classified as a hardwood despite the wood itself being very soft; it is the softest commercial hardwood and is widely used because of its light weight. Balsa trees grow extremely fast, often up to 27 metres in 10–15 years, and do not usually live beyond 30 to 40 years. In terms of volume (as opposed to height) they may be the fastest growing tree known; Streets mentions one individual which grew tall and diameter at breast height during a period of fifteen mo ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Rail Transport Modelling
Railway modelling (UK, Australia, New Zealand, and Ireland) or model railroading (US and Canada) is a hobby in which rail transport systems are Model building, modelled at a reduced Scale (ratio), scale. The scale models include locomotives, rolling stock, streetcars, rail tracks, tracks, Railway signal, signalling, Crane (machine), cranes, and landscapes including: countryside, roads, bridges, buildings, vehicles, harbors, urban landscape, model figures, lights, and features such as rivers, hills, tunnels, and canyons. The earliest model railways were the 'carpet railways' in the 1840s. The first documented model railway was the Railway of the Prince Imperial (French: Chemin de fer du Prince Impérial) built in 1859 by Emperor Napoleon III for his then 3-year-old son, also Louis-Napoléon, Prince Imperial, Napoleon, in the grounds of the Château de Saint-Cloud in Paris. It was powered by clockwork and ran in a figure-of-eight. Electric trains appeared around the start of t ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Model Yachting
Model yachting is the pastime of building and racing model yachts. It has always been customary for ship-builders to make a miniature model of the vessel under construction, which is in every respect a copy of the original on a small scale, whether steamship or sailing ship. There are fine collections to be seen at both general interest museums such as the Victoria and Albert Museum in London and at many specialized maritime museums worldwide. Many of these models are of exquisite workmanship, every rope, pulley or portion of the engine being faithfully reproduced. In the case of sailing yachts, these models were often pitted against each other on small bodies of water, and hence arose the modern pastime. It was soon seen that elaborate fittings and complicated rigging were a detriment to rapid handling, and that, on account of the comparatively stronger winds in which models were sailed, they needed a greater draught. For these reasons modern model yachts, which usually have fin ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
