Class Symbol TOPCAT K1 with 18 ft LOA TOPCAT K2 with 17 ft LOA TOPCAT K3 with 16,1 ft LOA The Topcat is a one-design sailing catamaran boat class which is divided into several boat sizes.

General

The Topcat sailing catamarans are fast, seaworthy, popular, and affordable twin-hull boats ranging in size from 3.60 m (12 ft) to 5.50 m (18 ft). They have world-wide distribution and are differentiated by: *Production of the hulls in

fiberglass Fiberglass (American English) or fibreglass ( Commonwealth English) is a common type of fiber-reinforced plastic using glass fiber. The fibers may be randomly arranged, flattened into a sheet called a chopped strand mat, or woven into glass clo ...

*Hull design without daggerboards *Assembly without bolts *Transportable on a trailer ''(width less than 2.55 m to comply with German traffic laws)'' *Transportable on the roof rack of a car *Simplification of existing designs

History

*1975 In the mid-70s two German A-Cat sailors, Bernd Breymann und Klaus Enzmann, were unhappy with the complicated transport and assembly of their boats. Klaus Enzmann build a first prototype without daggerboards or rudders, similar to the Spanish "Patin-Vela", but with many of the successful details of the later boats. *1976 The new "Kick-up" rudder was added to the prototype. The rudder and other Topcat details were registered as patents. *1977 The first Topcat appeared, a 4.80 m long twin-hull boat that was simply plugged together. It had a mast height of 7.00 m, a

jib A jib is a triangular sail that sets ahead of the foremast of a sailing vessel. Its tack is fixed to the bowsprit, to the bows, or to the deck between the bowsprit and the foremost mast. Jibs and spinnakers are the two main types of headsail ...

sail of 3.6 m², and a

mainsail A mainsail is a sail rigged on the main mast of a sailing vessel. * On a square rigged vessel, it is the lowest and largest sail on the main mast. * On a fore-and-aft rigged vessel, it is the sail rigged aft of the main mast. The sail's foot i ...

of 11.2 m². *1977-1979 Production of the first 60 Topcats. Capacity was limited by the rented wood shack, so the production of the hulls was moved to Italy, and company headquarters was moved to Gilching, Germany. In 1979 Bernd Breymann and Klaus Enzmann founded TOPCAT GmbH. Worldwide distribution of the boat was supported by onsite training. *1981 The first Topcat class association was established. The first Topcat bases were founded at the

Lake Garda Lake Garda ( it, Lago di Garda or ; lmo, label= Eastern Lombard, Lach de Garda; vec, Ƚago de Garda; la, Benacus; grc, Βήνακος) is the largest lake in Italy. It is a popular holiday location in northern Italy, about halfway between ...

. *1983 Creation of ITCA (International Topcat Class Association). In the same year the first European championship was held in Brenzone,

, with 44 boats from 5 countries. *1985 The faster and wider 18 ft dual-trapeze "Spitfire" model appeared. More volume was added to the hulls, which was much appreciated by heavier crews. Furthermore, the sails were redesigned, to improve low-wind performance. *1993-2000 Development of the modular K-series boats, to increase speed, safety, and handling. The K1, K2, and K3 boats are approved for ITCA racing. *2005 The 4.5 model was released, to address the low load-carrying capacity of the entry-level model. The 4.5 was renamed K4 in 2013, and relaunched as a youth-crew model. For young sailors the Topcat Chico model was developed. *2005 The Topcat was recognized as an official

ISAF ' ps, کمک او همکاري ' , allies = Afghanistan , opponents = Taliban Al-Qaeda , commander1 = , commander1_label = Commander , commander2 = , commander2_label = , commander3 = , command ...

racing class. The first world championship was held in September 2005 in Torbole at

Design

The Topcat lacks the dangerous main boom, as well as daggerboards, spreaders,

shroud Shroud usually refers to an item, such as a cloth, that covers or protects some other object. The term is most often used in reference to '' burial sheets'', mound shroud, grave clothes, winding-cloths or winding-sheets, such as the famous S ...

adjusters, and other complicated trimming mechanisms. To compensate for the missing daggerboards, the hull profiles are narrow and deep, and form a keel, similar to the Dart 18 and other beach catamarans. This is a compromise between lateral stability, agility in maneuvers, and ability to run up the beach. The material of the hulls is

, with a strength of a few millimeters on top and on the upper sides. Extra material is applied in areas subject to abrasion and stress forces: at the keel, and where the beams, shrouds, and rudders connect to the hulls. There are special boat versions with a build-up keel for sailing schools and for sailing areas with coral reefs. The surface of the hulls is covered by a

gelcoat Gelcoat, also called Gel Coat, is a material used to provide a high-quality finish on the visible surface of a fibre-reinforced composite. The most common gelcoats are thermosetting polymers based on epoxy or unsaturated polyester resin chemistry. ...

. Each hull has a dry storage compartment accessible by sealed hatch covers. The aluminum beams are plugged into the hulls, and the assembly is held together by a tightly laced

trampoline A trampoline is a device consisting of a piece of taut, strong fabric stretched between a steel frame using many coiled springs. Not all trampolines have springs, as the Springfree Trampoline uses glass-reinforced plastic rods. People bounce o ...

. The trampoline consists of two sheets of fabric. Each sheet has a round rubber edge that is threaded into an aluminum rail connected to the hull. The trampoline is laced in the middle, similar to a corset. For safety the front beam contains a line to assist in righting the boat after capsizing. The

rudder A rudder is a primary control surface used to steer a ship, boat, submarine, hovercraft, aircraft, or other vehicle that moves through a fluid medium (generally air or water). On an aircraft the rudder is used primarily to counter adve ...

s do not have to rotate upwards in low water, but slide upwards inside their cheek plates when a retaining line is pulled. The boat can still be steered when the rudders are at the keel line, this allows sailing in areas with low water levels. The rigging consist of an aero-dynamically shaped aluminum mast held by a forestay and two shroud wires. The mast sits on top of a round knob riveted to the front beam, and rotates freely. The K1 and Spitfire models have diamond spreaders to stabilize the mast. Some masts can be divided into two parts for easier transportation. There is a

trapeze A trapeze is a short horizontal bar hung by ropes or metal straps from a ceiling support. It is an aerial apparatus commonly found in circus performances. Trapeze acts may be static, spinning (rigged from a single point), swinging or flying, an ...

for the crew and/or helmsman. * The mainsail does not have a boom, and has full battens. The sail can be adjusted to wind conditions by a

cunningham Cunningham is a surname of Scottish origin, see Clan Cunningham. Notable people sharing this surname A–C * Aaron Cunningham (born 1986), American baseball player *Abe Cunningham, American drummer * Adrian Cunningham (born 1960), Australian ...

, and is connected to the mast top by a hook and latch system. The sail is controlled by a main sheet tackle with 7:1 or 8:1 mechanical advantage. The lower main sheet block has a cam cleat and an optional ratchet, and is connected to a traveller that runs the full length of the beam. * The jib is controlled by a jib sheet that runs through a block and cleat with a 2:1 mechanical advantage. Jib traveller and ratchet blocks are optional. A jib furling system is standard. * A

gennaker A gennaker is a sail that was developed around 1990. Used when sailing downwind, it is a cross between a genoa and a spinnaker. It is not symmetric like a true spinnaker but is asymmetric like a genoa, but the gennaker is not attached to the f ...

or reacher sail can be added to the K1, K2, K3 and K4 models, and allows a considerable speed increase when sailing

downwind Windward () and leeward () are terms used to describe the direction of the wind. Windward is ''upwind'' from the point of reference, i.e. towards the direction from which the wind is coming; leeward is ''downwind'' from the point of reference ...

. * The blocks in the racing versions are by

Harken Harken, Inc. is an international manufacturer specializing in performance sailing hardware, headquartered in Pewaukee, Wisconsin, United States. The company was founded in a 60-foot trailer in 1967 by brothers Peter Harken and Olaf Harken. Orig ...

. There are three sail types available: * Dacron Classic (Beginner) * Dacron Streamcut (Advanced)¹ * PenTex foil (Racing)¹ The Streamcut and PenTex sails have a larger sail area, and an almost rectangular shape. ¹ approved for racing by ITCA

Model overview and technical specifications

* K1 units build: 2920 total, 20 in 2013

References

External links