Honda C engine
   HOME

TheInfoList



OR:

Honda is a Japanese public multinational conglomerate manufacturer of automobiles, motorcycles, and power equipment, headquartered in Minato, Tokyo, Japan. Honda has been the world's largest motorcycle manufacturer since 1959, reaching a product ...
's first production V6 was the C series; it was produced in displacements from 2.0 to 3.5 liters. The C engine was produced in various forms for over 20 years (1985–2005), having first been used in the KA series Legend model, and its British sister car the Rover 800-series (and Sterling). All C engines share in common a 90-degree V-angle from bank to bank, common cylinder block bore centers, and four valves per cylinder. It is an all-aluminum design, and uses timing belt-driven single or dual overhead camshafts; the water pump is also driven by the timing belt. All C engines use an interference design; if the timing belt fails, any open valves will clash into the pistons, and severe engine damage will occur. The engine family can be broken down into three sub families: * C20A, C20AT, C25A and C27A (transversely mounted) * C30A and C32B (transversely mounted rear) * C32A, C35A, and C35B (one-off) (longitudinally mounted) As a general rule, interchange of parts will not work between these sub groups.


C20A

SOHC An overhead camshaft (OHC) engine is a piston engine where the camshaft is located in the cylinder head above the combustion chamber. This contrasts with earlier overhead valve engines (OHV), where the camshaft is located below the combustion cha ...
* at 6,500 rpm * at 5,500 rpm Japan only; * 1986–1988
Honda Legend :''Sections of this article are translated from Japanese Wikipedia''. The Honda Legend is a series of V6-engined executive cars/mid-size luxury sedans produced by Honda since 1985 which currently serves as its flagship vehicle. It is larger tha ...
* Experimental HP-X (Honda Pininfarina Xperimental) The
variable length intake manifold In internal combustion engines, a variable-length intake manifold (VLIM),variable intake manifold (VIM), or variable intake system (VIS) is an automobile internal combustion engine manifold technology. As the name implies, VLIM/VIM/VIS can vary ...
used six individual small-bore intake runners below 3,500 rpm for each cylinder and added an additional six individual larger bore intake runners at higher RPMs. The C20AT was a
turbocharged In an internal combustion engine, a turbocharger (often called a turbo) is a forced induction device that is powered by the flow of exhaust gases. It uses this energy to compress the intake gas, forcing more air into the engine in order to pro ...
version, called the "Wing Turbo", producing . Japan only: * 1989
Honda Legend :''Sections of this article are translated from Japanese Wikipedia''. The Honda Legend is a series of V6-engined executive cars/mid-size luxury sedans produced by Honda since 1985 which currently serves as its flagship vehicle. It is larger tha ...
Honda replaced the variable length
intake manifold In automotive engineering, an inlet manifold or intake manifold (in American English) is the part of an engine that supplies the fuel/air mixture to the cylinders. The word ''manifold'' comes from the Old English word ''manigfeald'' (from the ...
with a
variable geometry turbocharger Variable-geometry turbochargers (VGTs), occasionally known as variable-nozzle turbines (VNTs), are a type of turbochargers, usually designed to allow the effective aspect ratio of the turbocharger to be altered as conditions change. This is done ...
to the C20A engine used in the
Japanese Domestic Market Japanese domestic market (JDM) refers to Japan's home market for vehicles and vehicle parts. There is a common misconception that any Japanese branded car is JDM; however, this is not true. Only a vehicle made in Japan specifically to be sold i ...
Legend. The turbo with
intercooler An intercooler is a heat exchanger used to cool a gas after compression. Often found in turbocharged engines, intercoolers are also used in air compressors, air conditioners, refrigeration and gas turbines. Internal combustion engines Mo ...
-equipped engine was the C20AT engine and are extremely rare. Honda pioneered variable-geometry turbo chargers. The "Wing Turbo", as Honda called them, were controlled by an 8-bit processor ECU and they were constantly adjusting. Basically, at low speeds the wings surrounding the turbine wheel inside the compressor housing on the intake side would be nearly closed to speed and direct exhaust pressure precisely on the turbine wheel. At 2000 rpm, the wings would fluctuate and it would act like a much larger turbo to increase fuel economy as needed. This car was quick and powerful, but the price premium over the slightly longer and wider Legend with the
naturally aspirated Naturally may refer to: ;Albums * ''Naturally!'', an album by Nat Adderley * ''Naturally'' (Houston Person album) * ''Naturally'' (J. J. Cale album) * ''Naturally'' (John Pizzarelli album) * ''Naturally'' (Sharon Jones album) * ''Naturally'' ...
V6 was too much for most, so the car disappeared. This was one of the only production Hondas ever turbocharged from the factory (excluding turbo engines of
kei car Kei car (or , kanji: , "light automobile", ), known variously outside Japan as Japanese city car or Japanese microcar, is the Japanese vehicle category for the smallest highway-legal passenger cars with restricted dimensions and engine capacit ...
for the Japan domestic market), along with the K23A1 straight-4 engine used in the
Acura RDX The Acura RDX is a compact luxury crossover SUV produced by Acura, a luxury vehicle division of Honda, as the second crossover SUV offering from the brand after the mid-size MDX. Initially sharing its platform with the Honda Civic and CR-V, wi ...
and the ER
straight-4 engine A straight-four engine (also called an inline-four) is a four-cylinder Reciprocating engine, piston engine where cylinders are arranged in a line along a common crankshaft. The vast majority of automotive four-cylinder engines use a straight-f ...
used in the first generation
Honda City The is a subcompact car which has been produced by the Japanese manufacturer Honda since 1981. The City was originally a 3-door hatchback/2-door convertible for the Japanese, European and Australasian markets. The 3-door City was retired in 199 ...
until model year 2017, when most of their model lines had the option of the 1.5L
turbocharged In an internal combustion engine, a turbocharger (often called a turbo) is a forced induction device that is powered by the flow of exhaust gases. It uses this energy to compress the intake gas, forcing more air into the engine in order to pro ...
engine.


C25A

SOHC An overhead camshaft (OHC) engine is a piston engine where the camshaft is located in the cylinder head above the combustion chamber. This contrasts with earlier overhead valve engines (OHV), where the camshaft is located below the combustion cha ...
(2.5 L) V6 24 valves, 9.0:1 compression Japan * at 6,000 rpm * at 4,500 rpm North America: * 1986-1987
Honda Legend :''Sections of this article are translated from Japanese Wikipedia''. The Honda Legend is a series of V6-engined executive cars/mid-size luxury sedans produced by Honda since 1985 which currently serves as its flagship vehicle. It is larger tha ...
Sedan, 1986-1988 Rover 825 Sedan, ** at 5,800 rpm ** at 4,500 rpm ** UK and Europe (sold in US as Sterling 825i) The engine utilized a 90 degree V-angle to the crankshaft in preference to the taller but more common 60 degree design, with a compression ratio of 9.0:1. The
crankshaft A crankshaft is a mechanical component used in a piston engine to convert the reciprocating motion into rotational motion. The crankshaft is a rotating shaft containing one or more crankpins, that are driven by the pistons via the connecting ...
had crankpins offset 30 degrees to provide a low profile engine that fires smoothly and evenly. The block and cross flow
pent roof Numeral or number prefixes are prefixes derived from Numeral (linguistics), numerals or occasionally other numbers. In English and many other languages, they are used to coin numerous series of words. For example: * unicycle, bicycle, tricycle (1 ...
cylinder head In an internal combustion engine, the cylinder head (often abbreviated to simply "head") sits above the cylinders and forms the roof of the combustion chamber. In sidevalve engines, the head is a simple sheet of metal; whereas in more modern ov ...
s with 24 valves are
die-cast Die casting is a metal casting process that is characterized by forcing molten metal under high pressure into a mold cavity. The mold cavity is created using two hardened tool steel dies which have been machined into shape and work similarly t ...
from
aluminum alloy An aluminium alloy (or aluminum alloy; see spelling differences) is an alloy in which aluminium (Al) is the predominant metal. The typical alloying elements are copper, magnesium, manganese, silicon, tin, nickel and zinc. There are two principal ...
and the
cylinder bore In a piston engine, the bore (or cylinder bore) is the diameter of each cylinder. Engine displacement is calculated based on bore, stroke length and the number of cylinders: displacement = The stroke ratio, determined by dividing the bore by ...
s are lined with
cast iron Cast iron is a class of iron–carbon alloys with a carbon content more than 2%. Its usefulness derives from its relatively low melting temperature. The alloy constituents affect its color when fractured: white cast iron has carbide impuriti ...
. The
exhaust system An exhaust system is used to guide reaction exhaust gases away from a controlled combustion inside an engine or stove. The entire system conveys burnt gases from the engine and includes one or more exhaust pipes. Depending on the overall system ...
uses equal length
exhaust pipe An exhaust system is used to guide reaction exhaust gases away from a controlled combustion inside an engine or stove. The entire system conveys burnt gases from the engine and includes one or more exhaust pipes. Depending on the overall system ...
s connected to the
Exhaust manifold In automotive engineering, an exhaust manifold collects the exhaust gases from multiple cylinders into one pipe. The word ''manifold'' comes from the Old English word ''manigfeald'' (from the Anglo-Saxon ''manig'' anyand ''feald'' old and refe ...
to minimize scavenging resistance and maximum total exhaust efficiency. An external high capacity water cooled oil cooler and filter maintain an efficient oil temperature.


C27A

The
SOHC An overhead camshaft (OHC) engine is a piston engine where the camshaft is located in the cylinder head above the combustion chamber. This contrasts with earlier overhead valve engines (OHV), where the camshaft is located below the combustion cha ...
C27A is a 2.7 L version, with the major upgrade being the addition of a
variable length intake manifold In internal combustion engines, a variable-length intake manifold (VLIM),variable intake manifold (VIM), or variable intake system (VIS) is an automobile internal combustion engine manifold technology. As the name implies, VLIM/VIM/VIS can vary ...
, producing up to Applications; non-North America: * C27A2 - 1988-1990
Honda Legend :''Sections of this article are translated from Japanese Wikipedia''. The Honda Legend is a series of V6-engined executive cars/mid-size luxury sedans produced by Honda since 1985 which currently serves as its flagship vehicle. It is larger tha ...
Coupe, (non catalyst) UK and Europe * C27A2 - 1988-1990
Honda Legend :''Sections of this article are translated from Japanese Wikipedia''. The Honda Legend is a series of V6-engined executive cars/mid-size luxury sedans produced by Honda since 1985 which currently serves as its flagship vehicle. It is larger tha ...
Saloon, (non catalyst) UK and Europe * C27A2 - 1987-1991 Rover 827/Sterling/Vitesse, (non catalyst) UK and Europe * C27A1 - 1991 Rover 827/Sterling/Vitesse, (catalyst) UK and Europe * C27A1 - 1991-1995 Rover 827/Sterling/Coupe, (catalyst) UK and Europe Applications; North America: * C27A1 - 1987-1990
Acura Legend The Acura Legend is a mid-size luxury/executive car manufactured by Honda from Japan. It was sold in the U.S. and Canada under Honda's luxury brand, Acura, from 1985 until 1995 as both a sedan, which was classified as a full-size car, and a coupe ...
Coupe, (catalyst) * C27A1 - 1988-1990
Acura Legend The Acura Legend is a mid-size luxury/executive car manufactured by Honda from Japan. It was sold in the U.S. and Canada under Honda's luxury brand, Acura, from 1985 until 1995 as both a sedan, which was classified as a full-size car, and a coupe ...
, (catalyst) * C27A4 - 1995-1997
Honda Accord The , also known as the in Japan and China for certain generations, is a series of cars manufactured by Honda since 1976, best known for its four-door sedan variant, which has been one of the best-selling cars in the United States since 1989. ...
, (catalyst) For this particular vehicle the engine was updated with a more efficient intake manifold. * C27A1 - 1988-1991 Sterling 827, (catalyst)


C30A

The
DOHC An overhead camshaft (OHC) engine is a piston engine where the camshaft is located in the cylinder head above the combustion chamber. This contrasts with earlier overhead valve engines (OHV), where the camshaft is located below the combustion c ...
VTEC VTEC (Variable Valve Timing & Lift Electronic Control) is a system developed by Honda to improve the volumetric efficiency of a four-stroke internal combustion engine, resulting in higher performance at high RPM, and lower fuel consumption at low ...
C30A is a version, producing at 7,300 rpm and of
torque In physics and mechanics, torque is the rotational equivalent of linear force. It is also referred to as the moment of force (also abbreviated to moment). It represents the capability of a force to produce change in the rotational motion of th ...
at 6,500 rpm, with a 10.2:1 compression ratio. The engine has a bore and stroke of 90mm x 78mm, making the engine highly over square, which facilitates a shift in power to the higher end of the rpm range. The engine was the second Honda engine ever to utilize Honda's proprietary VTEC
variable valve timing In internal combustion engines, variable valve timing (VVT) is the process of altering the timing of a valve lift event, and is often used to improve performance, fuel economy or emissions. It is increasingly being used in combination with varia ...
system in an automotive application after the B16A, which adjusts cam lift and duration depending on engine
RPM Revolutions per minute (abbreviated rpm, RPM, rev/min, r/min, or with the notation min−1) is a unit of rotational speed or rotational frequency for rotating machines. Standards ISO 80000-3:2019 defines a unit of rotation as the dimensionl ...
and
throttle A throttle is the mechanism by which fluid flow is managed by constriction or obstruction. An engine's power can be increased or decreased by the restriction of inlet gases (by the use of a throttle), but usually decreased. The term ''throttle'' ...
position. VTEC allows the C30A to produce a high maximum power level while maintaining a relatively flat torque curve. C30A was also equipped with Variable Volume Induction System (VVIS), which used a primary and a secondary intake plenum. Secondary intake plenum engages at 4800 RPM to improve engines breathing ability and broadens torque curve.JDM Spec Engines - Honda C30A Engine
/ref> The C30A also made use of titanium
connecting rods A connecting rod, also called a 'con rod', is the part of a piston engine which connects the piston to the crankshaft. Together with the crank, the connecting rod converts the reciprocating motion of the piston into the rotation of the cranksha ...
, which was another first in a mass-production vehicle. The lightweight rods allowed a higher RPM to be achieved while maintaining the strength of traditional steel rods. The C30A block is an open-deck design made from an aluminum alloy with cylinders sleeved in ductile iron. The heads are 4 valves per
cylinder A cylinder (from ) has traditionally been a three-dimensional solid, one of the most basic of curvilinear geometric shapes. In elementary geometry, it is considered a prism with a circle as its base. A cylinder may also be defined as an infin ...
(24 valves per engine total), twin-cam design and contain the VTEC mechanism, which is actuated by oil pressure. For maximum performance, the C30A uses a
direct ignition A distributor is an enclosed rotating switch used in spark-ignition internal combustion engines that have mechanically timed ignition. The distributor's main function is to route high voltage current from the ignition coil to the spark plugs ...
system, with individual coils positioned directly over each cylinder
spark plug A spark plug (sometimes, in British English, a sparking plug, and, colloquially, a plug) is a device for delivering electric current from an ignition system to the combustion chamber of a spark-ignition engine to ignite the compressed fuel/air ...
. Due to its
DOHC An overhead camshaft (OHC) engine is a piston engine where the camshaft is located in the cylinder head above the combustion chamber. This contrasts with earlier overhead valve engines (OHV), where the camshaft is located below the combustion c ...
layout and its lightweight rotating assembly, the C30A is capable of reliable high RPM operation. Due to its complexity, cost and use of exotic materials, the C30A was used exclusively on Honda's NSX car. For NSXs equipped with a 4-speed automatic transmission, Honda used a slightly less powerful version of the C30A, with less aggressive
cam Calmodulin (CaM) (an abbreviation for calcium-modulated protein) is a multifunctional intermediate calcium-binding messenger protein expressed in all eukaryotic cells. It is an intracellular target of the secondary messenger Ca2+, and the bin ...
timing and producing . Though never mass produced, a heavily upgraded version of the engine was briefly used in GT-spec NSXs for the 2004 JGTC racing series by the Team Honda Racing
satellite team In motorsport, a satellite team is a team related to a larger, better-funded team. This relation may involve ownership, technical support and staff sharing, including drivers. Current examples include NASCAR outfit Wood Brothers Racing, which is c ...
. This engine was extensively modified by Mugen and was the first turbocharged Honda engine used in the series: prior GT-spec NSXs used a variant of the
naturally aspirated Naturally may refer to: ;Albums * ''Naturally!'', an album by Nat Adderley * ''Naturally'' (Houston Person album) * ''Naturally'' (J. J. Cale album) * ''Naturally'' (John Pizzarelli album) * ''Naturally'' (Sharon Jones album) * ''Naturally'' ...
C32B engine. Though the exact performance figures were kept secret, it is rumored to output more than . Applications: * 1991-1996
Honda NSX The Honda NSX, marketed in North America as the Acura NSX, is a two-seat, mid-engined coupe sports car manufactured by Honda. The origins of the NSX trace back to 1984, with the HP-X (Honda Pininfarina eXperimental) concept, which was a mid-eng ...
(5-Speed
Manual Transmission A manual transmission (MT), also known as manual gearbox, standard transmission (in Canada, the United Kingdom, and the United States), or stick shift (in the United States), is a multi-speed motor vehicle transmission (mechanics), transmission ...
) * 1991-2005
Honda NSX The Honda NSX, marketed in North America as the Acura NSX, is a two-seat, mid-engined coupe sports car manufactured by Honda. The origins of the NSX trace back to 1984, with the HP-X (Honda Pininfarina eXperimental) concept, which was a mid-eng ...
(4-Speed
Automatic Transmission An automatic transmission (sometimes abbreviated to auto or AT) is a multi-speed transmission used in internal combustion engine-based motor vehicles that does not require any input from the driver to change forward gears under normal driving c ...
) * 1994-1996
Honda NSX The Honda NSX, marketed in North America as the Acura NSX, is a two-seat, mid-engined coupe sports car manufactured by Honda. The origins of the NSX trace back to 1984, with the HP-X (Honda Pininfarina eXperimental) concept, which was a mid-eng ...
Le Mans Le Mans (, ) is a city in northwestern France on the Sarthe River where it meets the Huisne. Traditionally the capital of the province of Maine, it is now the capital of the Sarthe department and the seat of the Roman Catholic diocese of Le Man ...
* 2004 Honda NSX-GT
Super GT Super GT (stylized as SUPER GT) is a grand touring car racing series that began in 1993. Launched as the , generally referred to as either the JGTC or the All Japan Grand Touring Car Championship, the series was renamed to Super GT in 2005. It is ...


C32A

The C32A is a version. The
SOHC An overhead camshaft (OHC) engine is a piston engine where the camshaft is located in the cylinder head above the combustion chamber. This contrasts with earlier overhead valve engines (OHV), where the camshaft is located below the combustion cha ...
depending on model year, produces or . Applications; * C32A - SOHC USDM - and ** 1991-1995
Acura Legend The Acura Legend is a mid-size luxury/executive car manufactured by Honda from Japan. It was sold in the U.S. and Canada under Honda's luxury brand, Acura, from 1985 until 1995 as both a sedan, which was classified as a full-size car, and a coupe ...
sedan ** 1991-1992
Acura Legend The Acura Legend is a mid-size luxury/executive car manufactured by Honda from Japan. It was sold in the U.S. and Canada under Honda's luxury brand, Acura, from 1985 until 1995 as both a sedan, which was classified as a full-size car, and a coupe ...
coupé A coupe or coupé (, ) is a passenger car with a sloping or truncated rear roofline and two doors. The term ''coupé'' was first applied to horse-drawn carriages for two passengers without rear-facing seats. It comes from the French past parti ...
* C32A6 - SOHC USDM - and ** 1996-1998 Acura 3.2TL * C32A1 - Also known as the "Type-II"; uses a higher flowing intake manifold and slightly more aggressive camshaft - SOHC USDM - at 6200 rpm and at 5000 rpm. ** 1994-1995
Acura Legend The Acura Legend is a mid-size luxury/executive car manufactured by Honda from Japan. It was sold in the U.S. and Canada under Honda's luxury brand, Acura, from 1985 until 1995 as both a sedan, which was classified as a full-size car, and a coupe ...
GS sedan ** 1993-1995
Acura Legend The Acura Legend is a mid-size luxury/executive car manufactured by Honda from Japan. It was sold in the U.S. and Canada under Honda's luxury brand, Acura, from 1985 until 1995 as both a sedan, which was classified as a full-size car, and a coupe ...
LS and L coupe * C32A5 - SOHC JDM - and ** 1995-1998
Honda Inspire The is a mid-size sedan introduced by Honda in 1990 derived from Honda Accord chassis. The first Inspire debuted in 1990 as the Accord Inspire, a sister nameplate to the Honda Vigor, but sold at different retail channels in Japan, known as ''Ho ...
/Honda Saber


C32B

The C32B is a highly tuned
DOHC An overhead camshaft (OHC) engine is a piston engine where the camshaft is located in the cylinder head above the combustion chamber. This contrasts with earlier overhead valve engines (OHV), where the camshaft is located below the combustion c ...
V6 used in the
Honda NSX The Honda NSX, marketed in North America as the Acura NSX, is a two-seat, mid-engined coupe sports car manufactured by Honda. The origins of the NSX trace back to 1984, with the HP-X (Honda Pininfarina eXperimental) concept, which was a mid-eng ...
, which produces at 7,100 rpm and at 5,500 rpm of
torque In physics and mechanics, torque is the rotational equivalent of linear force. It is also referred to as the moment of force (also abbreviated to moment). It represents the capability of a force to produce change in the rotational motion of th ...
, retaining the 10.2:1 compression ratio from the C30A. The engine is essentially an update to the C30A and does not share commonality with the C32A. Honda increased
displacement Displacement may refer to: Physical sciences Mathematics and Physics *Displacement (geometry), is the difference between the final and initial position of a point trajectory (for instance, the center of mass of a moving object). The actual path ...
to through the use of larger
piston A piston is a component of reciprocating engines, reciprocating pumps, gas compressors, hydraulic cylinders and pneumatic cylinders, among other similar mechanisms. It is the moving component that is contained by a cylinder and is made gas-tig ...
s over the used in the C30A, while leaving the stroke the same. To accommodate the larger pistons, Honda used an advanced metallurgical technique on the cylinders called Fiber Reinforced Metal (FRM), in which an ultra lightweight alumina-carbon fiber is cast into the traditional aluminum alloy for enhanced rigidity. This process allowed thinner cylinder walls to be used while providing acceptable cooling characteristics. The C32B also used intake valves, which are larger than those in the C30A. Applications: * 1997-2005
Honda NSX The Honda NSX, marketed in North America as the Acura NSX, is a two-seat, mid-engined coupe sports car manufactured by Honda. The origins of the NSX trace back to 1984, with the HP-X (Honda Pininfarina eXperimental) concept, which was a mid-eng ...
(6-Speed
manual transmission A manual transmission (MT), also known as manual gearbox, standard transmission (in Canada, the United Kingdom, and the United States), or stick shift (in the United States), is a multi-speed motor vehicle transmission (mechanics), transmission ...
) * 1996-2002, 2005-2009 Honda NSX-GT
Super GT Super GT (stylized as SUPER GT) is a grand touring car racing series that began in 1993. Launched as the , generally referred to as either the JGTC or the All Japan Grand Touring Car Championship, the series was renamed to Super GT in 2005. It is ...
* 2002
Vemac RD320R The is a race car produced by the Vemac Car Company that raced in the Japanese Super GT GT300 class. It raced between 2002 and 2011 and completed over 150 races in Japan alone. Specifications When it was introduced in 2002, it used a Honda C e ...
Super GT Super GT (stylized as SUPER GT) is a grand touring car racing series that began in 1993. Launched as the , generally referred to as either the JGTC or the All Japan Grand Touring Car Championship, the series was renamed to Super GT in 2005. It is ...


C35A

The C35A is a
SOHC An overhead camshaft (OHC) engine is a piston engine where the camshaft is located in the cylinder head above the combustion chamber. This contrasts with earlier overhead valve engines (OHV), where the camshaft is located below the combustion cha ...
and carries the largest displacement of the C series at . The C35A was the first mass-produced engine to use block forged connecting rods contributing to precise balancing and an exceptionally strong bottom end. The C35 also contains a balance shaft to dampen engine vibrations associated with 90 degree design V6 engines. Besides the addition of these forged components, the overall design is similar to its smaller counterpart the C32A, with some parts being interchangeable. The 9.6:1 compression ratio of the C32A is also retained, despite the increase in displacement. Applications: * C35A - SOHC JDM - ** 1996-2004
Honda Legend :''Sections of this article are translated from Japanese Wikipedia''. The Honda Legend is a series of V6-engined executive cars/mid-size luxury sedans produced by Honda since 1985 which currently serves as its flagship vehicle. It is larger tha ...
* C35A1 - SOHC USDM - ** 1996-2001 Acura 3.5RL; at 5200 rpm and of torque at 2800 rpm ** 2002-2004 Acura 3.5RL; at 5200 rpm and of torque at 2800 rpm * C35A2 - SOHC EDM - ** 1996-1998
Honda Legend :''Sections of this article are translated from Japanese Wikipedia''. The Honda Legend is a series of V6-engined executive cars/mid-size luxury sedans produced by Honda since 1985 which currently serves as its flagship vehicle. It is larger tha ...
* C35A5 - SOHC EDM - ** 1998-2004
Honda Legend :''Sections of this article are translated from Japanese Wikipedia''. The Honda Legend is a series of V6-engined executive cars/mid-size luxury sedans produced by Honda since 1985 which currently serves as its flagship vehicle. It is larger tha ...


C35B

The C35B (name unconfirmed) is a
DOHC An overhead camshaft (OHC) engine is a piston engine where the camshaft is located in the cylinder head above the combustion chamber. This contrasts with earlier overhead valve engines (OHV), where the camshaft is located below the combustion c ...
V6 with
VTEC VTEC (Variable Valve Timing & Lift Electronic Control) is a system developed by Honda to improve the volumetric efficiency of a four-stroke internal combustion engine, resulting in higher performance at high RPM, and lower fuel consumption at low ...
which shares basic design properties with its
SOHC An overhead camshaft (OHC) engine is a piston engine where the camshaft is located in the cylinder head above the combustion chamber. This contrasts with earlier overhead valve engines (OHV), where the camshaft is located below the combustion cha ...
non-
VTEC VTEC (Variable Valve Timing & Lift Electronic Control) is a system developed by Honda to improve the volumetric efficiency of a four-stroke internal combustion engine, resulting in higher performance at high RPM, and lower fuel consumption at low ...
counterpart but with more aggressive camshafts and slightly lighter cylinder walls. This was the only
DOHC An overhead camshaft (OHC) engine is a piston engine where the camshaft is located in the cylinder head above the combustion chamber. This contrasts with earlier overhead valve engines (OHV), where the camshaft is located below the combustion c ...
VTEC VTEC (Variable Valve Timing & Lift Electronic Control) is a system developed by Honda to improve the volumetric efficiency of a four-stroke internal combustion engine, resulting in higher performance at high RPM, and lower fuel consumption at low ...
V6 ever built by
Honda is a Japanese public multinational conglomerate manufacturer of automobiles, motorcycles, and power equipment, headquartered in Minato, Tokyo, Japan. Honda has been the world's largest motorcycle manufacturer since 1959, reaching a product ...
for longitudinal applications and was only used in one non-production car, the Honda FS-X concept. Applications: * 1991 Honda FS-X concept -


See also

*
List of Honda engines This is a list of internal combustion engines models manufactured by the Honda Motor Company. Automotive Inline 2-cylinder * EH:1977–1988 Acty:1985–1988 Today Inline 3-cylinder * E07A-series ** 00–06 ECA1 (hybrid) ** 88–98 ...


References

{{Honda automotive engine timeline (2000-present) C V6 engines Engines by model Gasoline engines by model