RPM Ägypten 006

Revolutions per minute (abbreviated rpm, RPM, rev/min, r/min, or with the notation min⁻¹) is a unit of rotational speed or rotational frequency for rotating machines.

Standards

ISO 80000-3:2019 defines a unit of rotation as the dimensionless unit equal to 1, which it refers to as a revolution, but does not define the revolution as a unit. It defines a unit of rotational frequency equal to s⁻¹. The superseded standard ISO 80000-3:2006 did however state with reference to the unit name 'one', symbol '1', that "The special name revolution, symbol r, for this unit is widely used in specifications on rotating machines."

The International System of Units (SI) does not recognize rpm as a unit, and defines the unit of frequency, Hz, as equal to s⁻¹.

:$\begin 1~&\text &&=& 60~&\text \\ \frac~&\text &&=& 1~&\text \end$

A corresponding but distinct quantity for describing rotation is angular velocity, for which the SI unit is the radian per second.

Although they have the same dimensions (s⁻¹), hertz (Hz) and radian per second (rad/s) are two different units and are used to measure two different but proportional ISQ quantities: frequency and angular frequency (angular speed, magnitude of angular velocity) respectively. The conversions between a frequency and an angular velocity are:
:$\omega = 2 \pi f\,, \qquad f = \frac \,.$

Thus a disc rotating at 60 rpm is said to be have an angular speed of 2''π'' rad/s and a rotation frequency of 1 Hz.

Examples

*On many kinds of disc recording media, the rotational speed of the medium under the read head is a standard given in rpm. Phonograph (gramophone) records, for example, typically rotate steadily at , , 45 or 78 rpm (0.28, 0.55, 0.75, or 1.3 Hz respectively).
*Modern air turbine dental drills can rotate at up to 800,000 rpm (13.3 kHz).
*The second hand of a conventional analog clock rotates at 1 rpm.
*Audio CD players read their discs at a precise, constant rate (4.3218 Mbit/s of raw physical data for 1.4112 Mbit/s (176.4 kB/s) of usable audio data) and thus must vary the disc's rotational speed from 8 Hz (480 rpm) when reading at the innermost edge, to 3.5 Hz (210 rpm) at the outer edge.
*DVD players also usually read discs at a constant linear rate. The disc's rotational speed varies from 25.5 Hz (1530 rpm) when reading at the innermost edge, to 10.5 Hz (630 rpm) at the outer edge.
*A washing machine's drum may rotate at 500 to 2,000 rpm (8–33 Hz) during the spin cycles.
*A baseball thrown by a Major League Baseball pitcher can rotate at over 2,500 rpm (41.7 Hz); faster rotation yields more movement on breaking balls.
*A power generation turbine ( with a two-pole alternator) rotates at 3000 rpm (50 Hz) or 3600 rpm (60 Hz), depending on country – see AC power plugs and sockets.
* Modern automobile engines are typically operated around 2,000–3,000 rpm (33–50 Hz) when cruising, with a minimum (idle) speed around 750–900 rpm (12.5–15 Hz), and an upper limit anywhere from 4500 to 10,000 rpm (75–166 Hz) for a road car, very rarely reaching up to 12,000 rpm for certain cars (such as the GMA T.50), or 20,000 rpm for racing engines such as those in Formula 1 cars (during the season, with the 2.4 L N/A V8 engine configuration; limited to 15,000 rpm, with the 1.6 L V6 turbo-hybrid engine configuration). The exhaust note of V8, V10, and V12 F1 cars has a much higher pitch than an I4 engine, because each of the cylinders of a four-stroke engine fires once for every two revolutions of the crankshaft. Thus an eight-cylinder engine turning 300 times per second will have an exhaust note of 1,200 Hz.
*A piston aircraft engine typically rotates at a rate between 2,000 and 3,000 rpm (30–50 Hz).
*Computer hard drives typically rotate at 5,400 or 7,200 rpm (90 or 120 Hz), the most common speeds for the ATA or SATA-based drives in consumer models. High-performance drives (used in fileservers and enthusiast-gaming PCs) rotate at 10,000 or 15,000 rpm (160 or 250 Hz), usually with higher-level SATA, SCSI or Fibre Channel interfaces and smaller platters to allow these higher speeds, the reduction in storage capacity and ultimate outer-edge speed paying off in much quicker access time and average transfer speed thanks to the high spin rate. Until recently, lower-end and power-efficient laptop drives could be found with 4,200 or even 3,600 rpm spindle speeds (70 and 60 Hz), but these have fallen out of favour due to their lower performance, improvements in energy efficiency in faster models and the takeup of solid-state drives for use in slimline and ultraportable laptops. Similar to CD and DVD media, the amount of data that can be stored or read for each turn of the disc is greater at the outer edge than near the spindle; however, hard drives keep a constant rotational speed so the effective data rate is faster at the edge (conventionally, the "start" of the disc, opposite to a CD or DVD).
*Floppy disc drives typically ran at a constant 300 or occasionally 360 rpm (a relatively slow 5 or 6 Hz) with a constant per-revolution data density, which was simple and inexpensive to implement, though inefficient. Some designs such as those used with older Apple computers (Lisa, early Macintosh, later II's) were more complex and used variable rotational speeds and per-track storage density (at a constant read/record rate) to store more data per disc; for example, between 394 rpm (with 12 sectors per track) and 590 rpm (8 sectors) with Mac's 800 KB double-density drive at a constant 39.4 kB/s (max) – versus 300 rpm, 720 KB and 23 kB/s (max) for double-density drives in other machines.
*A Zippe-type centrifuge for enriching uranium spins at 90,000 rpm (1,500 Hz) or faster.
*Gas turbine engines rotate at tens of thousands of rpm. JetCat model aircraft turbines are capable of over 100,000 rpm (1,700 Hz) with the fastest reaching 165,000 rpm (2,750 Hz).
*A Flywheel energy storage system works at 60,000–200,000 rpm (1–3 kHz) range using a passively magnetic levitated flywheel in a vacuum. The choice of the flywheel material is not the most dense, but the one that pulverises the most safely, at surface speeds about 7 times the speed of sound.
*A typical 80 mm, 30 CFM computer fan will spin at 2,600–3,000 rpm (43–50 Hz) on 12-V DC power.
*A millisecond pulsar can have near 50,000 rpm (833 Hz).
*A turbocharger can reach 290,000 rpm (4.8 kHz), while 80,000–200,000 rpm (1–3 kHz) is common.
* A supercharger can spin at speeds between or as high as 50,000-65,000 rpm (833–1083 Hz)
*Molecular microbiology – molecular engines. The rotation rates of bacterial flagella have been measured to be 10,200 rpm (170 Hz) for ''Salmonella typhimurium'', 16,200 rpm (270 Hz) for ''Escherichia coli'', and up to 102,000 rpm (1,700 Hz) for polar flagellum of ''Vibrio alginolyticus'', allowing the latter organism to move in simulated natural conditions at a maximum speed of 540 mm/h.

See also

*Constant angular velocity (CAV) – used when referring to the speed of gramophone (phonograph) records
*Constant linear velocity (CLV) – used when referring to the speed of audio CDs
*Radian per second
*Rotational speed
*Compressor map
*Turn (geometry)
*Idle speed
* Overspeed (engine)
*Redline
*Rev limiter

References

{{reflist

Units of frequency
Units of angular velocity