Pushback (aviation)
   HOME

TheInfoList



OR:

In aviation, pushback is an airport procedure during which an aircraft is pushed backwards away from its parking position, usually at an airport
gate A gate or gateway is a point of entry to or from a space enclosed by walls. The word derived from old Norse "gat" meaning road or path; But other terms include ''yett and port''. The concept originally referred to the gap or hole in the wall ...
by external power. Pushbacks are carried out by special, low-profile vehicles called ''pushback tractors'' or ''tugs''. Although many aircraft are capable of moving themselves backwards on the ground using reverse thrust (a procedure referred to as a '' powerback),'' the resulting jet blast or prop wash would cause increased noise, damage to the terminal building or equipment, and hurt airport staff due to high-speed debris. This debris would also be sucked into the engine, as it is in normal use, and cause excessive wear - a major cause of wear on aircraft engines is during ground use. A pushback is therefore the preferred method when ground-handling aircraft.


Definition

IATA The International Air Transport Association (IATA ) is a trade association of the world's airlines founded in 1945. IATA has been described as a cartel since, in addition to setting technical standards for airlines, IATA also organized tariff ...
defines aircraft pushback as "rearward moving of an aircraft from a parking position to a taxi position by use of specialized ground support equipment."


Procedure

Pushbacks at busy aerodromes are usually subject to ground control clearance to facilitate ground movement on taxiways. Once clearance is obtained, the pilot will communicate with the tractor driver (or a ground handler walking alongside the aircraft in some cases) to start the pushback. To communicate, a headset may be connected near the nose gear. Since the pilots cannot see what is behind the aircraft, steering is done by the pushback tractor driver and not by the pilots. Depending on the aircraft type and airline procedure, a ''bypass pin'' may be temporarily installed into the nose gear to disconnect it from the aircraft's normal steering mechanism. Once the pushback is completed, the towbar is disconnected, and any bypass pin removed. The ground handler will show the bypass pin to the pilots to make it clear that it has been removed. The pushback is then complete, and the aircraft can taxi forward under its own power.


Equipment


Moving light aircraft

Very small airplanes may be moved by human power alone. The airplane may be pushed or pulled by landing gear or wing struts since they're known to be strong enough to drag the airplane through the air. To allow for turns, a person may either pick up or push down on the tail to raise either the nose wheel or
tail wheel Conventional landing gear, or tailwheel-type landing gear, is an aircraft undercarriage consisting of two main wheels forward of the center of gravity and a small wheel or skid to support the tail.Crane, Dale: ''Dictionary of Aeronautical Terms ...
off the ground, then rotate the airplane by hand. A less cumbersome method involves attaching a short tow bar to either the nose wheel or tail wheel, which provides a solid handhold and leverage to steer with, as well as eliminates the danger of handling the propeller. These tow bars are usually a lightweight
aluminum alloy An aluminium alloy (or aluminum alloy; see spelling differences) is an alloy in which aluminium (Al) is the predominant metal. The typical alloying elements are copper, magnesium, manganese, silicon, tin, nickel and zinc. There are two principal ...
construction which allows them to be carried on board the airplane. Other small tow bars have a powered wheel to help move the airplane, with power sources as diverse as lawnmower engines or battery-operated electric drills. However, powered tow bars are usually too large and heavy to be practically carried on small airplanes.


Tractors and towbars

Large aircraft cannot be moved by hand and must have a tractor or tug. Pushback tractors use a low profile design to fit under the aircraft nose. For sufficient traction the tractor must be heavy, and most models can have extra ballast added. A typical tractor for large aircraft weighs up to and has a drawbar pull of . Often the driver's cabin can be raised for increased visibility when reversing and lowered to fit under aircraft. There are two types of pushback tractors: conventional and towbarless (TBL). Conventional tugs use a tow bar to connect the tug to the nose landing gear of the aircraft. The tow bar is fixed laterally at the nose landing gear, but may move slightly vertically for height adjustment. At the end that attaches to the tug, the tow bar may pivot freely laterally and vertically. In this manner the tow bar acts as a large lever to rotate the nose landing gear. Each aircraft type has a unique tow fitting so the towbar also acts as an adapter between the standard-sized tow pin on the tug and the type-specific fitting on the aircraft's landing gear. The tow bar must be long enough to place the tug far away enough to avoid hitting the aircraft and to provide sufficient leverage to facilitate turns. On heavy tow bars for large aircraft the towbar rides on its own wheels when not connected to an aircraft. The wheels are attached to a hydraulic jacking mechanism which can lift the towbar to the correct height to mate to both the airplane and the tug, and once this is accomplished the same mechanism is used in reverse to raise the tow bar wheels from the ground during the pushback process. The tow bar can be connected at the front or the rear of the tractor, depending on whether the aircraft will be pushed or pulled. The towbar has a shear pin which prevents the aircraft from being mishandled by the tug; when overstressed the shear pin will snap, disconnecting the bar from the nose gear to prevent damage to the aircraft and tug. Towbarless (TBL) tractors do not use a towbar; they scoop up the nose landing gear and lift it off the ground. This avoids the time penalty of connecting/disconnecting a towbar, and entirely removes the cost/complexity of maintaining towbars on the ramp. The tug itself does not need to be particularly massive - the aircraft's nosewheel weight provides the necessary downward force. Lastly, a TBL tug is much shorter (compared to a tug+towbar system) and has only a single pivot point instead of one at either end of the towbar, so it has much simpler and precise control of the aircraft. This is very useful in general aviation settings with a wider variety of aircraft in more confined spaces than their airline counterparts. Manufacturers of electric TBL tugs offer models capable of moving any aircraft from the smallest single-engine type to narrow-body airliners, military cargo and airline-sized business jets. Just as specialized towbars are required for a wide range of aircraft, many TBL tugs use adapters which enable the movement of many unique aircraft. The majority of aircraft do not require adapters and can be moved without any special adjustments to the tug. This is in contrast to conventional tugs which often use so-called "universal" towbars which must be adjustable to suit many aircraft types. Electric TBL tugs are gaining popularity among general aviation operators and FBOs as an alternative to gas or diesel-powered conventional tugs. Being electric rather than internal combustion-powered, electric tugs are low-emission which is a major advantage for environmentally-conscious operators; this also enables the tug to be safely operated inside a closed hangar.


Robotic tractor/tug

The Lahav Division of Israel Aerospace Industries has developed a semi-robotic towbarless tractor it calls TaxiBot that can tow an aircraft from the terminal gate to the take-off point (taxi-out phase) and return it to the gate after landing (taxi-in phase). The TaxiBot eliminates the use of airplane engines during taxi-in and until immediately prior to take-off during taxi-out potentially saving airlines billions of dollars in fuel that is used. The TaxiBot is controlled by the pilot from the cockpit using the regular pilot controls. British Airways has been using a similar sort of tug too.


Other equipment applications

While the vehicle is referred to as a ''pushback tug'', it is also used to tow aircraft in areas where taxiing the aircraft is not practical or is unsafe, such as moving aircraft in and out of maintenance hangars, or moving aircraft that are not under their own power. Some airlines, notably Virgin Atlantic, advocated towing aircraft to the holding point of the runway to save fuel and reduce environmental impact. However, the practice was discontinued after landing gear maintenance costs increased due to the stress put on the landing gear during the towing process.Ellie Zolfagharifard, "Reducing runway emissions", ''The Engineer'', December 7, 2009.
/ref> Some fuel must still be burned to operate the auxiliary power unit to provide electrical and pneumatic power to run lighting, environmental and communications systems, unless the tug itself provides these sources of power, which some do. This method also places a larger workload on ground crews and equipment, especially if the aircraft and tow tractor ends up having to wait in a long line of aircraft.


In media

In an advertising campaign, also documented on the television show '' Fifth Gear'', a Volkswagen Touareg was used to pull a
Boeing 747 The Boeing 747 is a large, long-range wide-body airliner designed and manufactured by Boeing Commercial Airplanes in the United States between 1968 and 2022. After introducing the 707 in October 1958, Pan Am wanted a jet times its size, t ...
. As cited before, the "tractor" needs to be heavy to aid traction. The Touareg carried 4.3 tons worth of cement bags, and the tires were inflated to twice the normal pressure to handle the extra weight. Tractor tires have high sidewall ratios for that reason. This is the world record for the heaviest load towed by a production car.


Gallery

File:KLM 777 pushback.jpg, A KLM Boeing 777 being pushed back from a gate at
Narita International Airport Narita International Airport ( ja, 成田国際空港, Narita Kokusai Kūkō) , also known as Tokyo-Narita, formerly and originally known as , is one of two international airports serving the Greater Tokyo Area, the other one being Haneda Airport ...
File:Tow truck ekch.jpg, Pushback tug with the towbar behind File:KLM Pushback tractor and ground power unit.jpg, Towbarless tractor File:ILA 2008 PD 542.JPG, Towbarless tractor for smaller aircraft File:T813 6x6 civil.jpg, A Tatra T813 6x6 Airport tug File:Pushback tractor in front of Easyjet A319.JPG, A tug ready to push back an EasyJet Airbus A319 File:Unimog pushback.jpg, A Unimog being used as a pushback tractor File:Aircraft towing, SE-LTU Saab 2000.jpg, A Saab 2000 being towed by a small tow tractor at Ängelholm-Helsingborg Airport File:De Havilland DHC-1 Chipmunk (G-AKDN) ground handled at Fairford 7Jul2016 arp.jpg, de Havilland Chipmunk manually ground handled at the 2016 Royal International Air Tattoo, England File:Batik air pk-lum pushback.jpg, An Indonesia Batik air A320 on pushback at Soekarno–Hatta International Airport File:BelAZ 74271 aircraft tractor 2.jpg, BelAZ 74271 airport tug with double cab File:Towbarless Aircraft tug NadHaf IAF Equipment.jpg, Towbarless tug (NadHaf) for
fighter aircraft Fighter aircraft are fixed-wing military aircraft designed primarily for air-to-air combat. In military conflict, the role of fighter aircraft is to establish air superiority of the battlespace. Domination of the airspace above a battlefield ...
in Israeli Air Force


See also

* Aircraft ground handling * Ground support equipment * Visual Guidance Docking Systems (VGDS)


References

{{Reflist


Sources

* Operations Manual Bucher aircraft tractor Kp20FlApt13 * Schweizerische Militärmuseum Full Aircraft ground handling Tractors Articles containing video clips