In
semiconductor
A semiconductor is a material which has an electrical resistivity and conductivity, electrical conductivity value falling between that of a electrical conductor, conductor, such as copper, and an insulator (electricity), insulator, such as glas ...
manufacturing plasma ashing is the process of removing the
photoresist
A photoresist (also known simply as a resist) is a light-sensitive material used in several processes, such as photolithography and photoengraving, to form a patterned coating on a surface. This process is crucial in the electronic industry.
T ...
(light sensitive coating) from an
etched wafer. Using a
plasma
Plasma or plasm may refer to:
Science
* Plasma (physics), one of the four fundamental states of matter
* Plasma (mineral), a green translucent silica mineral
* Quark–gluon plasma, a state of matter in quantum chromodynamics
Biology
* Blood pla ...
source, a
monatomic
In physics and chemistry, "monatomic" is a combination of the words "mono" and "atomic", and means "single atom". It is usually applied to gases: a monatomic gas is a gas in which atoms are not bound to each other. Examples at standard conditions ...
(single atom) substance known as a reactive species is generated.
Oxygen
Oxygen is the chemical element with the symbol O and atomic number 8. It is a member of the chalcogen group in the periodic table, a highly reactive nonmetal, and an oxidizing agent that readily forms oxides with most elements as wel ...
or
fluorine
Fluorine is a chemical element with the symbol F and atomic number 9. It is the lightest halogen and exists at standard conditions as a highly toxic, pale yellow diatomic gas. As the most electronegative reactive element, it is extremely reacti ...
are the most common reactive species. Other gases used are N2/H2 where the H2 portion is 2%. The reactive species combines with the photoresist to form ash which is removed with a
vacuum pump
A vacuum pump is a device that draws gas molecules from a sealed volume in order to leave behind a partial vacuum. The job of a vacuum pump is to generate a relative vacuum within a capacity. The first vacuum pump was invented in 1650 by Otto v ...
.
Typically, monatomic oxygen plasma is created by exposing oxygen gas (O
2) at a low pressure to
high power radio waves, which ionise it. This process is done under vacuum in order to create a plasma. As the plasma is formed, many
free radical
A daughter category of ''Ageing'', this category deals only with the biological aspects of ageing.
Ageing
Ailments of unknown cause
Biogerontology
Biological processes
Causes of death
Cellular processes
Gerontology
Life extension
Metabo ...
s are created which could damage the wafer. Newer, smaller circuitry is increasingly susceptible to these particles. Originally, plasma was generated in the process chamber, but as the need to get rid of free radicals has increased, many machines now use a downstream plasma configuration, where plasma is formed remotely and the desired particles are channeled to the wafer. This allows electrically charged particles time to recombine before they reach the wafer surface, and prevents damage to the wafer surface.
Types
Two forms of plasma ashing are typically performed on wafers. High temperature ashing, or stripping, is performed to remove as much photo resist as possible, while the "descum" process is used to remove residual photo resist in trenches. The main difference between the two processes is the temperature the wafer is exposed to while in an ashing chamber. Typical issues arise when this photoresist has undergone an implant step previously and heavy metal are embedded in the photoresist and it has experienced high temperatures causing it to be resistant to oxidizing.
Monatomic oxygen is electrically neutral and although it does recombine during the channeling, it does so at a slower rate than the positively or negatively charged free radicals, which attract one another. This means that when all of the free radicals have recombined, there is still a portion of the active species available for process. Because a large portion of the active species is lost to recombination, process times may take longer. To some extent, these longer process times can be mitigated by increasing the temperature of the reaction area. This also contribute to the observation of the spectral optical traces, these can be what is normally expected when the emission declines, the process is over; it can also mean that spectral lines increase in illuminance as the available reactants are consumed causing a rise in certain spectral lines representing the available ionic species.
See also
*
Plasma etching
Plasma etching is a form of plasma processing used to fabricate integrated circuits. It involves a high-speed stream of glow discharge ( plasma) of an appropriate gas mixture being shot (in pulses) at a sample. The plasma source, known as etch spe ...
Semiconductor device fabrication
Plasma processing
References
{{materials-sci-stub