![Hydraulic Force Torque 275px](https://upload.wikimedia.org/wikipedia/commons/e/e7/Hydraulic_Force_Torque_275px.png)
Hydraulic machines use
liquid
A liquid is a nearly incompressible fluid that conforms to the shape of its container but retains a (nearly) constant volume independent of pressure. As such, it is one of the four fundamental states of matter (the others being solid, gas, a ...
fluid power to perform work.
Heavy construction vehicles are a common example. In this type of machine,
hydraulic fluid
A hydraulic fluid or hydraulic liquid is the medium by which power is transferred in hydraulic machinery. Common hydraulic fluids are based on mineral oil or water. Examples of equipment that might use hydraulic fluids are excavators and backhoe ...
is pumped to various
hydraulic motors and
hydraulic cylinders throughout the machine and becomes pressurized according to the resistance present. The fluid is controlled directly or automatically by
control valves and distributed through hoses, tubes, or pipes.
Hydraulic systems, like
pneumatic system
Pneumatics (from Greek ‘wind, breath’) is a branch of engineering that makes use of gas or pressurized air.
Pneumatic systems used in industry are commonly powered by compressed air or compressed inert gases. A centrally located and ele ...
s, are based on
Pascal's law
Pascal's law (also Pascal's principle or the principle of transmission of fluid-pressure) is a principle in fluid mechanics given by Blaise Pascal that states that a pressure change at any point in a confined incompressible fluid is transmitted ...
which states that any pressure applied to a fluid inside a closed system will transmit that pressure equally everywhere and in all directions. A hydraulic system uses an incompressible
liquid
A liquid is a nearly incompressible fluid that conforms to the shape of its container but retains a (nearly) constant volume independent of pressure. As such, it is one of the four fundamental states of matter (the others being solid, gas, a ...
as its fluid, rather than a compressible gas.
The popularity of hydraulic machinery is due to the very large amount of power that can be transferred through small tubes and flexible hoses, the high power density and a wide array of
actuator
An actuator is a component of a machine that is responsible for moving and controlling a mechanism or system, for example by opening a valve. In simple terms, it is a "mover".
An actuator requires a control device (controlled by control signal) a ...
s that can make use of this power, and the huge multiplication of forces that can be achieved by applying pressures over relatively large areas. One drawback, compared to
machines using gears and shafts, is that any transmission of power results in some losses due to resistance of fluid flow through the piping.
History
Joseph Bramah
Joseph Bramah (13 April 1748 – 9 December 1814), born Stainborough Lane Farm, Stainborough, in Barnsley, Yorkshire, was an English inventor and locksmith. He is best known for having improved the flush toilet and inventing the hydraulic pr ...
patented the
hydraulic press in 1795.
While working at Bramah's shop,
Henry Maudslay
Henry Maudslay ( pronunciation and spelling) (22 August 1771 – 14 February 1831) was an English machine tool innovator, tool and die maker, and inventor. He is considered a founding father of machine tool technology. His inventions were a ...
suggested a cup leather packing. Because it produced superior results, the hydraulic press eventually displaced the
steam hammer
A steam hammer, also called a drop hammer, is an industrial power hammer driven by steam that is used for tasks such as shaping forgings and driving piles. Typically the hammer is attached to a piston that slides within a fixed cylinder, but i ...
for metal forging.
To supply large-scale power that was impractical for individual steam engines, central station hydraulic systems were developed. Hydraulic power was used to operate cranes and other machinery in British ports and elsewhere in Europe. The largest hydraulic system was in London. Hydraulic power was used extensively in
Bessemer steel production. Hydraulic power was also used for elevators, to operate canal locks and rotating sections of bridges.
Some of these systems remained in use well into the twentieth century.
Harry Franklin Vickers
Harry Franklin Vickers (October 1, 1898 – January 12, 1977) was an American inventor and industrialist. He grew up in Montana and southern California. He was called the "Father of Industrial Hydraulics" by the American Society of Mechanical Engi ...
was called the "Father of Industrial Hydraulics" by
ASME.
Force and torque multiplication
A fundamental feature of hydraulic systems is the ability to apply force or torque multiplication in an easy way, independent of the distance between the input and output, without the need for mechanical gears or levers, either by altering the effective areas in two connected cylinders or the effective displacement (cc/rev) between a pump and motor. In normal cases, hydraulic ratios are combined with a mechanical force or torque ratio for optimum machine designs such as boom movements and track drives for an excavator.
Examples
Two hydraulic cylinders interconnected
Cylinder C1 is one inch in radius, and cylinder C2 is ten inches in radius. If the force exerted on C1 is 10
lbf
The pound of force or pound-force (symbol: lbf, sometimes lbf,) is a unit of force used in some systems of measurement, including English Engineering units and the foot–pound–second system.
Pound-force should not be confused with pound-m ...
, the force exerted by C2 is 1000 lbf because C2 is a hundred times larger in area (''S'' = π''r''²) as C1. The downside to this is that you have to move C1 a hundred inches to move C2 one inch. The most common use for this is the classical
hydraulic jack
A jack is a mechanical lifting device used to apply great forces or lift heavy loads. A mechanical jack employs a screw thread for lifting heavy equipment. A hydraulic jack uses hydraulic power. The most common form is a car jack, floor jack o ...
where a pumping cylinder with a small diameter is connected to the lifting cylinder with a large diameter.
Pump and motor
If a hydraulic rotary pump with the displacement 10 cc/rev is connected to a hydraulic rotary motor with 100 cc/rev, the shaft torque required to drive the pump is one-tenth of the torque then available at the motor shaft, but the shaft speed (rev/min) for the motor is also only one-tenth of the pump shaft speed. This combination is actually the same type of force multiplication as the cylinder example, just that the linear force in this case is a rotary force, defined as torque.
Both these examples are usually referred to as a
hydraulic transmission or hydrostatic transmission involving a certain hydraulic "gear ratio".
Hydraulic circuits
A hydraulic circuit is a system comprising an interconnected set of discrete components that transport
liquid
A liquid is a nearly incompressible fluid that conforms to the shape of its container but retains a (nearly) constant volume independent of pressure. As such, it is one of the four fundamental states of matter (the others being solid, gas, a ...
. The purpose of this system may be to control where fluid flows (as in a network of tubes of coolant in a thermodynamic system) or to control fluid
pressure
Pressure (symbol: ''p'' or ''P'') is the force applied perpendicular to the surface of an object per unit area over which that force is distributed. Gauge pressure (also spelled ''gage'' pressure)The preferred spelling varies by country and e ...
(as in hydraulic amplifiers). For example, hydraulic machinery uses hydraulic circuits (in which
hydraulic fluid
A hydraulic fluid or hydraulic liquid is the medium by which power is transferred in hydraulic machinery. Common hydraulic fluids are based on mineral oil or water. Examples of equipment that might use hydraulic fluids are excavators and backhoe ...
is pushed, under pressure, through
hydraulic pump
Hydraulic pumps are used in hydraulic drive systems and can be hydrostatic or hydrodynamic. A hydraulic pump is a mechanical source of power that converts mechanical power into hydraulic energy ( hydrostatic energy i.e. flow, pressure). It generat ...
s, pipes, tubes, hoses,
hydraulic motors,
hydraulic cylinders, and so on) to move heavy loads. The approach of describing a fluid system in terms of discrete components is inspired by the success of electrical
circuit theory. Just as electric circuit theory works when elements are discrete and linear, hydraulic circuit theory works best when the elements (passive components such as pipes or transmission lines or active components such as power packs or
pumps) are discrete and linear. This usually means that hydraulic circuit analysis works best for long, thin tubes with discrete pumps, as found in chemical process flow systems or microscale devices.
The circuit comprises the following components:
* Active components
**
Hydraulic power pack
Hydraulics (from Greek: Υδραυλική) is a technology and applied science using engineering, chemistry, and other sciences involving the mechanical properties and use of liquids. At a very basic level, hydraulics is the liquid counter ...
* Transmission lines
** Hydraulic hoses
* Passive components
**
Hydraulic cylinders
For the hydraulic fluid to do work, it must flow to the actuator and/or motors, then return to a reservoir. The fluid is then
filtered and re-pumped. The path taken by hydraulic fluid is called a
hydraulic circuit of which there are several types.
* Open center circuits use pumps that supply a continuous flow. The flow is returned to ''tank'' through the control valve's ''open center''; that is, when the control valve is centered, it provides an open return path to the tank and the fluid is not pumped to high pressure. Otherwise, if the control valve is actuated it routes fluid to and from an actuator and tank. The fluid's pressure will rise to meet any resistance, since the pump has a constant output. If the pressure rises too high, fluid returns to the tank through a
pressure relief valve. Multiple control valves may be stacked in serie
This type of circuit can use inexpensive, constant displacement pumps.
* Closed center circuits supply full pressure to the control valves, whether any valves are actuated or not. The pumps vary their flow rate, pumping very little hydraulic fluid until the operator actuates a valve. The valve's spool therefore doesn't need an open center return path to tank. Multiple valves can be connected in a parallel arrangement and system pressure is equal for all valves.
Open loop circuits
Open-loop: Pump-inlet and motor-return (via the directional valve) are connected to the hydraulic tank. The term loop applies to feedback; the more correct term is open versus closed "circuit". Open center circuits use pumps which supply a continuous flow. The flow is returned to the tank through the control valve's open center; that is, when the control valve is centered, it provides an open return path to the tank and the fluid is not pumped to a high pressure. Otherwise, if the control valve is actuated it routes fluid to and from an actuator and tank. The fluid's pressure will rise to meet any resistance, since the pump has a constant output. If the pressure rises too high, fluid returns to the tank through a pressure relief valve. Multiple control valves may be stacked in series. This type of circuit can use inexpensive, constant displacement pumps.
Closed loop circuits
Closed-loop: Motor-return is connected directly to the pump-inlet. To keep up pressure on the low pressure side, the circuits have a charge pump (a small gear pump) that supplies cooled and filtered oil to the low pressure side. Closed-loop circuits are generally used for hydrostatic transmissions in mobile applications. ''Advantages:'' No directional valve and better response, the circuit can work with higher pressure. The pump swivel angle covers both positive and negative flow direction. ''Disadvantages:'' The pump cannot be utilized for any other hydraulic function in an easy way and cooling can be a problem due to limited exchange of oil flow. High power closed loop systems generally must have a 'flush-valve' assembled in the circuit in order to exchange much more flow than the basic leakage flow from the pump and the motor, for increased cooling and filtering. The flush valve is normally integrated in the motor housing to get a cooling effect for the oil that is rotating in the motor housing itself. The losses in the motor housing from rotating effects and losses in the ball bearings can be considerable as motor speeds will reach 4000-5000 rev/min or even more at maximum vehicle speed. The leakage flow as well as the extra flush flow must be supplied by the charge pump. A large charge pump is thus very important if the transmission is designed for high pressures and high motor speeds. High oil temperature is usually a major problem when using hydrostatic transmissions at high vehicle speeds for longer periods, for instance when transporting the machine from one work place to the other. High oil temperatures for long periods will drastically reduce the lifetime of the transmission. To keep down the oil temperature, the system pressure during transport must be lowered, meaning that the minimum displacement for the motor must be limited to a reasonable value. Circuit pressure during transport around 200-250 bar is recommended.
Closed loop systems in mobile equipment are generally used for the transmission as an alternative to mechanical and hydrodynamic (converter) transmissions. The advantage is a stepless gear ratio (continuously variable speed/torque) and a more flexible control of the gear ratio depending on the load and operating conditions. The hydrostatic transmission is generally limited to around 200 kW maximum power, as the total cost gets too high at higher power compared to a hydrodynamic transmission. Large wheel loaders for instance and heavy machines are therefore usually equipped with converter transmissions. Recent technical achievements for the converter transmissions have improved the efficiency and developments in the software have also improved the characteristics, for example selectable gear shifting programs during operation and more gear steps, giving them characteristics close to the hydrostatic transmission.
Constant pressure and load-sensing systems
Hydrostatic transmissions for earth moving machines, such as for track loaders, are often equipped with a separate '
inch pedal
An inch pedal or inching pedal is a pedal used in many models of mobile machinery with a hydraulic pilot pressure output proportional to the pedal position, or an electronic pedal with a proportional electric signal output. The pedal is used in h ...
' that is used to temporarily increase the diesel engine rpm while reducing the vehicle speed in order to increase the available hydraulic power output for the working hydraulics at low speeds and increase the tractive effort. The function is similar to stalling a converter gearbox at high engine rpm. The inch function affects the preset characteristics for the 'hydrostatic' gear ratio versus diesel engine rpm.
Constant pressure systems
The closed center circuits exist in two basic configurations, normally related to the regulator for the variable pump that supplies the oil:
* Constant pressure systems (CP), standard. Pump pressure always equals the pressure setting for the pump regulator. This setting must cover the maximum required load pressure. Pump delivers flow according to required sum of flow to the consumers. The CP system generates large power losses if the machine works with large variations in load pressure and the average system pressure is much lower than the pressure setting for the pump regulator. CP is simple in design, and works like a pneumatic system. New hydraulic functions can easily be added and the system is quick in response.
* Constant pressure systems, unloaded. Same basic configuration as 'standard' CP system but the pump is unloaded to a low stand-by pressure when all valves are in neutral position. Not so fast response as standard CP but pump lifetime is prolonged.
Load-sensing systems
Load-sensing systems (LS) generate less power losses as the pump can reduce both flow and pressure to match the load requirements, but require more tuning than the CP system with respect to system stability. The LS system also requires additional logical valves and compensator valves in the directional valves, thus it is technically more complex and more expensive than the CP system. The LS system generates a constant power loss related to the regulating pressure drop for the pump regulator :
The average
is around 2 MPa (290 psi). If the pump flow is high the extra loss can be considerable. The power loss also increases if the load pressures vary a lot. The cylinder areas, motor displacements and mechanical torque arms must be designed to match load pressure in order to bring down the power losses. Pump pressure always equals the maximum load pressure when several functions are run simultaneously and the power input to the pump equals the (max. load pressure + Δ''p''
LS) x sum of flow.
Five basic types of load sensing systems
# Load sensing ''without compensators'' in the directional valves. Hydraulically controlled LS pump.
# Load sensing ''with up-stream compensator'' for each connected directional valve. Hydraulically controlled LS pump.
# Load sensing ''with down-stream compensator'' for each connected directional valve. Hydraulically controlled LS pump.
# Load sensing ''with a combination of up-stream and down-stream compensators''. Hydraulically controlled LS pump.
# Load sensing with synchronized, both electric controlled pump displacement and electric controlled valve flow area for faster response, increased stability and fewer system losses. This is a new type of LS-system, not yet fully developed.
Technically the down-stream mounted compensator in a valve block can physically be mounted "up-stream", but work as a down-stream compensator.
System type (3) gives the advantage that activated functions are synchronized independent of pump flow capacity. The flow relation between two or more activated functions remains independent of load pressures, even if the pump reaches the maximum swivel angle. This feature is important for machines that often run with the pump at maximum swivel angle and with several activated functions that must be synchronized in speed, such as with excavators. With the type (4) system, the functions with ''up-stream'' compensators have priority, for example the steering function for a wheel loader. The system type with down-stream compensators usually have a unique trademark depending on the manufacturer of the valves, for example "LSC" (Linde Hydraulics), "LUDV" (
Bosch Rexroth
Bosch Rexroth AG is an engineering firm based in Lohr am Main in Germany. It is the result of a merger on 1 May 2001 between Mannesmann Rexroth AG and the Automation Technology Business Unit of Robert Bosch GmbH, and is a wholly owned subsidiar ...
Hydraulics) and "Flowsharing" (Parker Hydraulics) etc. No official standardized name for this type of system has been established but flowsharing is a common name for it.
Components
Hydraulic pump
Hydraulic pump
Hydraulic pumps are used in hydraulic drive systems and can be hydrostatic or hydrodynamic. A hydraulic pump is a mechanical source of power that converts mechanical power into hydraulic energy ( hydrostatic energy i.e. flow, pressure). It generat ...
s supply fluid to the components in the system. Pressure in the system develops in reaction to the load. Hence, a pump rated for 5,000 psi is capable of maintaining flow against a load of 5,000 psi.
Pumps have a
power density
Power density is the amount of power (time rate of energy transfer) per unit volume.
In energy transformers including batteries, fuel cells, motors, power supply units etc., power density refers to a volume, where it is often called volume p ...
about ten times greater than an electric motor (by volume). They are powered by an electric motor or an engine, connected through gears, belts, or a flexible
elastomer
An elastomer is a polymer with viscoelasticity (i.e. both viscosity and elasticity) and with weak intermolecular forces, generally low Young's modulus and high failure strain compared with other materials. The term, a portmanteau of ''elastic p ...
ic coupling to reduce vibration.
Common types of hydraulic pumps to hydraulic machinery applications are:
*
Gear pump: cheap, durable (especially in g-rotor form), simple. Less efficient, because they are constant (fixed) displacement, and mainly suitable for pressures below 20 MPa (3000 psi).
*
Vane pump
A rotary vane pump is a positive-displacement pump that consists of vanes mounted to a rotor that rotates inside a cavity. In some cases these vanes can have variable length and/or be tensioned to maintain contact with the walls as the pump rotates ...
: cheap and simple, reliable. Good for higher-flow low-pressure output.
*
Axial piston pump
An axial piston pump is a positive displacement pump that has a number of pistons in a circular array within a ''cylinder block''. It can be used as a stand-alone pump, a hydraulic motor or an automotive air conditioning compressor.
Description
...
: many designed with a variable displacement mechanism, to vary output flow for automatic control of pressure. There are various axial piston pump designs, including swashplate (sometimes referred to as a valveplate pump) and checkball (sometimes referred to as a wobble plate pump). The most common is the
swashplate
A swashplate, also known as slant disk, was invented by Anthony Michell in 1917. It is a mechanical engineering device used to translate the motion of a rotating shaft into reciprocating motion, or vice versa. The working principle is similar to c ...
pump. A variable-angle swashplate causes the pistons to reciprocate a greater or lesser distance per rotation, allowing output flow rate and pressure to be varied (greater displacement angle causes higher flow rate, lower pressure, and vice versa).
*
Radial piston pump: normally used for very high pressure at small flows.
Piston pumps are more expensive than gear or vane pumps, but provide longer life operating at higher pressure, with difficult fluids and longer continuous duty cycles. Piston pumps make up one half of a
hydrostatic transmission
A continuously variable transmission (CVT) is an automatic transmission that can change seamlessly through a continuous range of gear ratios. This contrasts with other transmissions that provide a limited number of gear ratios in fixed steps. T ...
.
Control valves
![Hydraulic control pad with valves](https://upload.wikimedia.org/wikipedia/commons/7/70/Hydraulic_control_pad_with_valves.jpg)
''
Directional control valve
Direction may refer to:
*Relative direction, for instance left, right, forward, backwards, up, and down
** Anatomical terms of location for those used in anatomy
** List of ship directions
* Cardinal direction
Mathematics and science
* Directi ...
s'' route the fluid to the desired actuator. They usually consist of a spool inside a
cast iron
Cast iron is a class of iron–carbon alloys with a carbon content more than 2%. Its usefulness derives from its relatively low melting temperature. The alloy constituents affect its color when fractured: white cast iron has carbide impuriti ...
or
steel
Steel is an alloy made up of iron with added carbon to improve its strength and fracture resistance compared to other forms of iron. Many other elements may be present or added. Stainless steels that are corrosion- and oxidation-resistant ty ...
housing. The spool slides to different positions in the housing, and intersecting grooves and channels route the fluid based on the spool's position.
The spool has a central (neutral) position maintained with springs; in this position the supply fluid is blocked, or returned to tank. Sliding the spool to one side routes the hydraulic fluid to an actuator and provides a return path from the actuator to tank. When the spool is moved to the opposite direction the supply and return paths are switched. When the spool is allowed to return to neutral (center) position the actuator fluid paths are blocked, locking it in position.
Directional control valves are usually designed to be stackable, with one valve for each hydraulic cylinder, and one fluid input supplying all the valves in the stack.
Tolerances are very tight in order to handle the high pressure and avoid leaking, spools typically have a
clearance with the housing of less than a thousandth of an inch (25 µm). The valve block will be mounted to the machine's frame with a ''three point'' pattern to avoid distorting the valve block and jamming the valve's sensitive components.
The spool position may be actuated by mechanical levers, hydraulic ''pilot'' pressure, or
solenoid
upright=1.20, An illustration of a solenoid
upright=1.20, Magnetic field created by a seven-loop solenoid (cross-sectional view) described using field lines
A solenoid () is a type of electromagnet formed by a helix, helical coil of wire whose ...
s which push the spool left or right. A
seal allows part of the spool to protrude outside the housing, where it is accessible to the actuator.
The main valve block is usually a stack of ''off the shelf'' directional control valves chosen by flow capacity and performance. Some valves are designed to be proportional (flow rate proportional to valve position), while others may be simply on-off. The control valve is one of the most expensive and sensitive parts of a hydraulic circuit.
*
Pressure relief valves are used in several places in hydraulic machinery; on the return circuit to maintain a small amount of pressure for brakes, pilot lines, etc... On hydraulic cylinders, to prevent overloading and hydraulic line/seal rupture. On the hydraulic reservoir, to maintain a small positive pressure which excludes moisture and contamination.
*
Pressure regulator
A pressure regulator is a valve that controls the pressure of a fluid or gas to a desired value, using negative feedback from the controlled pressure. Regulators are used for gases and liquids, and can be an integral device with a pressure setti ...
s reduce the supply pressure of hydraulic fluids as needed for various circuits.
* Sequence valves control the sequence of hydraulic circuits; to ensure that one hydraulic cylinder is fully extended before another starts its stroke, for example. Hydraulic circuits can perform a sequence of operations automatically, such as trip-and-reclose three times, then lockout, of an oil-interrupting
recloser
In electric power distribution, automatic circuit reclosers (ACRs) are a class of switchgear designed for use on overhead electricity distribution networks to detect and interrupt transient faults. Also known as reclosers or autoreclosers, ACRs a ...
.
["Reclosers: maintenance instructions"]
Section ""Recloser operation".
p. 3-4.
*
Shuttle valve
A shuttle valve is a type of valve which allows fluid to flow through it from one of two sources. Generally a shuttle valve is used in pneumatic systems, although sometimes it will be found in hydraulic systems.
Structure and function
The basic s ...
s provide a logical
or function.
*
Check valve
A check valve, non-return valve, reflux valve, retention valve, foot valve, or one-way valve is a valve that normally allows fluid (liquid or gas) to flow through it in only one direction.
Check valves are two-port valves, meaning they have t ...
s are one-way valves, allowing an accumulator to charge and maintain its pressure after the machine is turned off, for example.
* Pilot controlled check valves are one-way valve that can be opened (for both directions) by a foreign pressure signal. For instance if the load should not be held by the check valve anymore. Often the foreign pressure comes from the other pipe that is connected to the motor or cylinder.
* Counterbalance valves are in fact a special type of pilot controlled check valve. Whereas the check valve is open or closed, the counterbalance valve acts a bit like a pilot controlled flow control.
* Cartridge valves are in fact the inner part of a check valve; they are ''off the shelf'' components with a standardized envelope, making them easy to populate a proprietary valve block. They are available in many configurations; on/off, proportional, pressure relief, etc. They generally screw into a valve block and are electrically controlled to provide logic and automated functions.
*
Hydraulic fuses are in-line safety devices designed to automatically seal off a hydraulic line if pressure becomes too low, or safely vent fluid if pressure becomes too high.
* Auxiliary valves in complex hydraulic systems may have auxiliary valve blocks to handle various duties unseen to the operator, such as accumulator charging, cooling fan operation, air conditioning power, etc. They are usually custom valves designed for the particular machine, and may consist of a metal block with ports and channels drilled. Cartridge valves are threaded into the ports and may be electrically controlled by switches or a microprocessor to route fluid power as needed.
Actuators
*
Hydraulic cylinder
*
Hydraulic motor (a pump plumbed in reverse); hydraulic motors with axial configuration use swashplates for highly accurate control and also in 'no stop' continuous (360°) precision positioning mechanisms. These are frequently driven by several hydraulic pistons acting in sequence.
*
Hydrostatic transmission
A continuously variable transmission (CVT) is an automatic transmission that can change seamlessly through a continuous range of gear ratios. This contrasts with other transmissions that provide a limited number of gear ratios in fixed steps. T ...
*
Brakes
A brake is a mechanical device that inhibits motion by absorbing energy from a moving system. It is used for slowing or stopping a moving vehicle, wheel, axle, or to prevent its motion, most often accomplished by means of friction.
Background ...
Reservoir
The hydraulic fluid reservoir holds excess hydraulic fluid to accommodate volume changes from: cylinder extension and contraction, temperature driven expansion and contraction, and leaks. The reservoir is also designed to aid in separation of air from the fluid and also work as a heat accumulator to cover losses in the system when peak power is used. Reservoirs can also help separate dirt and other particulate from the oil, as the particulate will generally settle to the bottom of the tank.
Some designs include dynamic flow channels on the fluid's return path that allow for a smaller reservoir.
Accumulators
Accumulators are a common part of hydraulic machinery. Their function is to store energy by using pressurized gas. One type is a tube with a floating piston. On the one side of the piston there is a charge of pressurized gas, and on the other side is the fluid. Bladders are used in other designs. Reservoirs store a system's fluid.
Examples of accumulator uses are backup power for steering or brakes, or to act as a shock absorber for the hydraulic circuit.
Hydraulic fluid
Also known as ''tractor fluid'', hydraulic fluid is the life of the hydraulic circuit. It is usually petroleum oil with various additives. Some hydraulic machines require fire resistant fluids, depending on their applications. In some factories where food is prepared, either an edible oil or water is used as a working fluid for health and safety reasons.
In addition to transferring energy, hydraulic fluid needs to
lubricate
Lubrication is the process or technique of using a lubricant to reduce friction and wear and tear in a contact between two surfaces. The study of lubrication is a discipline in the field of tribology.
Lubrication mechanisms such as fluid-lubrica ...
components, suspend contaminants and metal filings for transport to the filter, and to function well to several hundred degrees Fahrenheit or Celsius.
Filters
Filters are an important part of hydraulic systems which removes the unwanted particles from fluid. Metal particles are continually produced by mechanical components and need to be removed along with other contaminants.
Filters may be positioned in many locations. The filter may be located between the reservoir and the pump intake. Blockage of the filter will cause
cavitation
Cavitation is a phenomenon in which the static pressure of a liquid reduces to below the liquid's vapour pressure, leading to the formation of small vapor-filled cavities in the liquid. When subjected to higher pressure, these cavities, cal ...
and possibly failure of the pump. Sometimes the filter is located between the pump and the control valves. This arrangement is more expensive, since the filter housing is pressurized, but eliminates cavitation problems and protects the control valve from pump failures. The third common filter location is just before the return line enters the reservoir. This location is relatively insensitive to blockage and does not require a pressurized housing, but contaminants that enter the reservoir from external sources are not filtered until passing through the system at least once. Filters are used from 7 micron to 15 micron depends upon the viscosity grade of hydraulic oil.
Tubes, pipes and hoses
''Hydraulic
tubes'' are seamless steel precision pipes, specially manufactured for hydraulics. The tubes have standard sizes for different pressure ranges, with standard diameters up to 100 mm. The tubes are supplied by manufacturers in lengths of 6 m, cleaned, oiled and plugged. The tubes are interconnected by different types of flanges (especially for the larger sizes and pressures), welding cones/nipples (with o-ring seal), several types of flare connection and by cut-rings. In larger sizes, hydraulic pipes are used. Direct joining of tubes by welding is not acceptable since the interior cannot be inspected.
''Hydraulic
pipe'' is used in case standard hydraulic tubes are not available. Generally these are used for low pressure. They can be connected by threaded connections, but usually by welds. Because of the larger diameters the pipe can usually be inspected internally after welding.
Black pipe is
non-galvanized and suitable for
welding
Welding is a fabrication (metal), fabrication process that joins materials, usually metals or thermoplastics, by using high heat to melt the parts together and allowing them to cool, causing Fusion welding, fusion. Welding is distinct from lower ...
.
''Hydraulic
hose
A hose is a flexible hollow tube designed to carry fluids from one location to another. Hoses are also sometimes called ''pipes'' (the word ''pipe'' usually refers to a rigid tube, whereas a hose is usually a flexible one), or more generally '' ...
'' is graded by pressure, temperature, and fluid compatibility. Hoses are used when pipes or tubes can not be used, usually to provide flexibility for machine operation or maintenance. The hose is built up with rubber and steel layers. A rubber interior is surrounded by multiple layers of woven wire and rubber. The exterior is designed for abrasion resistance. The bend radius of hydraulic hose is carefully designed into the machine, since hose failures can be deadly, and violating the hose's minimum bend radius will cause failure. Hydraulic hoses generally have steel fittings
swaged
Swaging () is a forging process in which the dimensions of an item are altered using dies into which the item is forced. Swaging is usually a cold working process, but also may be hot worked.
The term swage may apply to the process (verb) or ...
on the ends. The weakest part of the high pressure hose is the connection of the hose to the fitting. Another disadvantage of hoses is the shorter life of rubber which requires periodic replacement, usually at five to seven year intervals.
Tubes and pipes for hydraulic n applications are internally oiled before the system is commissioned. Usually steel piping is painted outside. Where flare and other couplings are used, the paint is removed under the nut, and is a location where corrosion can begin. For this reason, in marine applications most piping is stainless steel.
Seals, fittings and connections
Components of a hydraulic system
ources (e.g. pumps), controls (e.g. valves) and actuators (e.g. cylinders)need connections that will contain and direct the hydraulic fluid without leaking or losing the pressure that makes them work. In some cases, the components can be made to bolt together with fluid paths built-in. In more cases, though, rigid tubing or flexible hoses are used to direct the flow from one component to the next. Each component has entry and exit points for the fluid involved (called ports) sized according to how much fluid is expected to pass through it.
There are a number of standardized methods in use to attach the hose or tube to the component. Some are intended for ease of use and service, others are better for higher system pressures or control of leakage. The most common method, in general, is to provide in each component a female-threaded port, on each hose or tube a female-threaded captive nut, and use a separate adapter fitting with matching male threads to connect the two. This is functional, economical to manufacture, and easy to service.
Fittings serve several purposes;
* To join components with ports of different sizes.
* To bridge different standards;
O-ring boss to
JIC, or
pipe threads to
face seal
A face seal is a seal in which the sealing surfaces are normal to the axis of the seal. Face seals are typically used in static applications and are used to prevent leakage in the radial direction with respect to the axis of the seal. Face seals a ...
, for example.
* To allow proper orientation of components, a 90°, 45°, straight, or swivel fitting is chosen as needed. They are designed to be positioned in the correct orientation and then tightened.
* To incorporate bulkhead hardware to pass the fluid through an obstructing wall.
* A ''quick disconnect'' fitting may be added to a machine without modification of hoses or valves
A typical piece of machinery or heavy equipment may have thousands of sealed connection points and several different types:
*
Pipe fittings
A fitting or adapter is used in pipe systems to connect straight sections of pipe (fluid conveyance), pipe or tube (fluid conveyance), tube, adapt to different sizes or shapes, and for other purposes such as regulating (or measuring) fluid flow. ...
, the fitting is screwed in until tight, difficult to orient an angled fitting correctly without over or under tightening.
* O-ring boss, the fitting is screwed into a boss and orientated as needed, an additional nut tightens the fitting, washer and
o-ring in place.
*
Flare fittings, are metal to metal compression seals deformed with a cone nut and pressed into a flare mating.
*
Face seal
A face seal is a seal in which the sealing surfaces are normal to the axis of the seal. Face seals are typically used in static applications and are used to prevent leakage in the radial direction with respect to the axis of the seal. Face seals a ...
, metal flanges with a groove and o-ring seal are fastened together.
* Beam seals are costly metal to metal seals used primarily in aircraft.
*
Swage
Swaging () is a forging process in which the dimensions of an item are altered using dies into which the item is forced. Swaging is usually a cold working process, but also may be hot worked.
The term swage may apply to the process (verb) or ...
d seals, tubes are connected with fittings that are swaged permanently in place. Primarily used in aircraft.
Elastomeric seals (O-ring boss and face seal) are the most common types of seals in heavy equipment and are capable of reliably sealing more than of fluid pressure.
See also
*
Automatic transmission
An automatic transmission (sometimes abbreviated to auto or AT) is a multi-speed transmission used in internal combustion engine-based motor vehicles that does not require any input from the driver to change forward gears under normal driving c ...
*
Brake fluid
Brake fluid is a type of hydraulic fluid used in hydraulic brake and hydraulic clutch applications in automobiles, motorcycles, light trucks, and some bicycles. It is used to transfer force into pressure, and to amplify braking force. It works be ...
*
Fluidics
Fluidics, or fluidic logic, is the use of a fluid to perform analog signal, analog or Digital data, digital operations similar to those performed with electronics.
The physical basis of fluidics is pneumatics and hydraulics, based on the theoret ...
*
Hagen–Poiseuille equation
In nonideal fluid dynamics, the Hagen–Poiseuille equation, also known as the Hagen–Poiseuille law, Poiseuille law or Poiseuille equation, is a physical law that gives the pressure drop in an incompressible and Newtonian fluid in laminar flow ...
*
High-density solids pump High-density solids pumps are hydrostatically operating machines which displace the medium being pumped and thus create a flow.
High-density solids and their transport
High-density solids are mixtures of liquid and solid constituents; examples incl ...
*
Hydraulics
**
Hydraulic brake
A hydraulic brake is an arrangement of braking mechanism which uses brake fluid, typically containing glycol ethers or diethylene glycol, to transfer pressure from the controlling mechanism to the braking mechanism.
History
During 1904, Frederick ...
**
Hydraulic drive system
*
Hydraulic analogy
*
National Fluid Power Association
The National Fluid Power Association (NFPA) is an American 501(c)6 industry trade association, founded in 1953.
The NFPA's mission is to serve as a forum where all fluid power channel partners work together to advance fluid power technology, str ...
*
Sidelifter
*
Hydraulic press
*
Pascal's law
Pascal's law (also Pascal's principle or the principle of transmission of fluid-pressure) is a principle in fluid mechanics given by Blaise Pascal that states that a pressure change at any point in a confined incompressible fluid is transmitted ...
References and notes
* Hydraulic Power System Analysis, A. Akers, M. Gassman, & R. Smith, Taylor & Francis, New York, 2006,
External links
''Facts worth knowing about hydraulics'', Danfoss Hydraulics, 1.4Mb pdf fileOn-line re-print of U.S. Army Field Manual 5-499Information about Fluid Power is also available on the National Fluid *Power Association web-site nfpa.com
{{Authority control
Engineering vehicles
Fluid dynamics
Machinery, Hydraulic