Background
As a product concept, the Celeron was introduced in response to Intel's loss of the low-end market, in particular to the Cyrix 6x86, the AMD K6, and the IDTDesktop Celerons
P6-based Celerons
Covington
Launched in April 1998, the first ''Covington'' Celeron was essentially a 266 MHz Pentium II manufactured without any secondary cache at all. Covington also shared the 80523 product code of Deschutes. Although clocked at 266 or 300 MHz (frequencies 33 or 66 MHz higher than the desktop version of the Pentium w/MMX), the cacheless Celerons had trouble outcompeting the parts they were designed to replace. Substantial numbers were sold on first release, largely on the strength of the Intel name, but the Celeron quickly achieved a poor reputation both in the trade press and among computer professionals. The initial market interest faded rapidly in the face of its poor performance, and with sales at a very low level, Intel felt obliged to develop a substantially faster replacement as soon as possible. Nevertheless, the first Celerons were quite popular among some overclockers, for their flexible overclockability and reasonable price. Covington was only manufactured in Slot 1 SEPP format.Mendocino
The ''Mendocino'' Celeron, launched August 24, 1998, was the first retail CPU to use on-die L2 cache. Whereas Covington had no secondary cache at all, Mendocino included 128 KB of L2 cache running at full clock rate. The first Mendocino-core Celeron was clocked at a then-modest 300 MHz but offered almost twice the performance of the old cacheless Covington Celeron at the same clock rate. To distinguish it from the older Covington 300 MHz, Intel called the Mendocino core Celeron ''300A''. Although the other Mendocino Celerons (the 333 MHz part, for example) did not have an ''A'' appended, some people call all Mendocino processors ''Celeron-A'' regardless of clock rate. The new Mendocino-core Celeron was a good performer from the outset. Indeed, most industry analysts regarded the first Mendocino-based Celerons as ''too'' successful—performance was sufficiently high to not only compete strongly with rival parts, but also to attract buyers away from Intel's high-profit flagship, the Pentium II. Overclockers soon discovered that, given a high-end motherboard, many Celeron 300A CPUs could run reliably at 450 MHz. This was achieved by simply increasing the front-side bus (FSB) clock rate from the stock 66 MHz to the 100 MHz clock of the Pentium II, helped by several facts: the 440BX chipset with nominal support for 100 MHz and correspondent memory had already been on the market, and the internal L2 cache was more tolerant to overclocking than external cache chips, which already had to run at half-CPU speed by design. At this frequency, the budget Mendocino Celeron rivaled the fastest x86 processors available. Some motherboards were designed to prevent this modification, by restricting the Celeron's front side bus to 66 MHz. However, overclockers soon found that putting tape over pin B21 of the Celeron's interface slot circumvented this, allowing a 100 MHz bus. At the time on-die cache was difficult to manufacture; especially L2 as more of it is needed to attain an adequate level of performance. A benefit of on-die cache is that it operates at the same clock rate as the CPU. All other Intel CPUs at that time used motherboard mounted or slot mounted secondary L2 cache, which was very easy to manufacture, cheap, and simple to enlarge to any desired size (typical cache sizes were 512 KB or 1 MB), but they carried the performance penalty of slower cache performance, typically running at FSB frequency of 60 to 100 MHz. The Pentium II's 512 KB of L2 cache was implemented with a pair of relatively high-performance L2 cache chips mounted on a special-purpose board alongside the processor itself, running at half the processor's clock rate and communicating with the CPU through a special back-side bus. This method of cache placement was expensive and imposed practical cache-size limits, but allowed the Pentium II to be clocked higher and avoided front side bus RAM/L2 cache contention typical with motherboard-placed L2 cache configurations. Over time, newer Mendocino processors were released at 333, 366, 400, 433, 466, 500, and 533 MHz. The Mendocino Celeron CPU came only designed for a 66 MHz front-side bus, but this would not be a serious performance bottleneck until clock rates reached higher levels. The Mendocino Celerons also introduced new packaging. When the Mendocinos debuted they came in both a Slot 1 SEPP and Socket 370 PPGA package. The Slot 1 form had been designed to accommodate the off-chip cache of the Pentium II and had mounting problems with motherboards. Because all Celerons are a single-chip design, however, there was no reason to retain the slot packaging for L2 cache storage, and Intel discontinued the Slot 1 variant; beginning with the 466 MHz part, only the PPGA Socket 370 form was offered. (Third-party manufacturers made motherboard slot-to-socket adapters (nicknamed Slotkets) available for a few dollars, which allowed, for example, a Celeron 500 to be fitted to a Slot 1 motherboard.) One interesting note about the PPGA Socket 370 Mendocinos is they supported symmetric multiprocessing (SMP), and there was at least one motherboard released (theCoppermine-128
The next generation Celeron was the '' ' Coppermine-128' '' (sometimes known as the ''Celeron II''). These were a derivative of Intel's ''Coppermine''Tualatin-256
These Celeron processors, released initially at 1.2 GHz on October 2, 2001, were based on the Pentium III ' Tualatin' core and made with a 0.13 micrometer process for the FCPGA 2 Socket 370. They were nicknamed "Tualeron" by some enthusiasts — a portmanteau of the words Tualatin and Celeron. Some software and users refer to the chips as ''Celeron-S'', referring to the chip's lineage with the Pentium III-S, but this is not an official designation. Intel later released 1 GHz and 1.1 GHz parts (which were given the extension ''A'' to their name to differentiate them from the Coppermine-128 of the same clock rate they replaced). A 1.3 GHz chip, launched January 4, 2002, and finally a 1.4 GHz chip, launched May 15, 2002 (the same day as the 1.7 GHz Willamette-based Celeron launch), marked the end of the Tualatin-256 line. The most significant differences compared to the Pentium III Tualatin are a lower 100 MHz bus and fixed 256 KB of L2 cache (whereas the Pentium III was offered with either 256 KB or 512 KB L2 cache); cache associativity stayed at 8-way, although the newly introduced data prefetching appears to have been disabled. Furthermore, the Tualatin-256's L2 cache has a higher latency which boosted manufacturing yields for this budget CPU. On the other hand, this improved stability when overclocking and most of them had no problem working at 133 MHz FSB for a substantial performance increase. Despite offering much improved performance over the Coppermine Celeron it superseded, the Tualatin Celeron still suffered stiff competition from AMD'sNetBurst-based Celerons
Willamette-128
These Celerons were for socket 478 and were based on the '' Willamette''Northwood-128
These socket 478 Celerons are based on the '' Northwood'' Pentium 4 core, and also have 128 KB of L2 cache. The only difference between the ''Northwood-128''-based and the ''Willamette-128''-based Celeron is the fact that it was built on the new 130 nm process which shrank the die size, increased the transistor count, and lowered the core voltage from 1.7 V on the ''Willamette-128'' to 1.52 V for the ''Northwood-128''. Despite these differences, they are functionally the same as the Willamette-128 Celeron, and perform largely the same clock-for-clock. The ''Northwood-128'' family of processors were initially released as a 2 GHz core (a 1.9 GHz model was announced earlier, but never launched) on September 18, 2002. Since that time Intel has released at total of 10 different clock speeds ranging from 1.8 GHz to 2.8 GHz, before being surpassed by the Celeron D. Although the ''Northwood''-based Celerons suffer considerably from their small L2 cache, some clock rates have been favored in the enthusiast market because, like the old 300A, they can run well above their specified clock rate. In Intel's "Family/Model/Stepping" scheme, Northwood Celerons and Pentium 4s are family 15, model 2, and their Intel product code is 80532.Prescott-256
Prescott-256 Celeron D processors, initially launched June 25, 2004, featuring double the L1 cache (16 KB) and L2 cache (256 KB) as compared to the previous Willamette and Northwood desktop Celerons, by virtue of being based on the '' Prescott'' Pentium 4 core. It also features a 533 MT/s bus and SSE3, and a 3xx model number (compared to 5xx for Pentium 4s and 7xx for Pentium Ms). The Prescott-256 Celeron D was manufactured forCedar Mill-512
Based on the ''Cedar Mill'' Pentium 4 core, this version of the Celeron D was launched May 28, 2006, and continued the 3xx naming scheme with the Celeron D 347 (3.06 GHz), 352 (3.2 GHz), 356 (3.33 GHz), 360 (3.46 GHz), and 365 (3.6 GHz). The Cedar Mill Celeron D is largely the same as the Prescott-256, except with double the L2 cache (512 KB) and based on a 65 nm manufacturing process. The Cedar Mill-512 Celeron D is LGA 775 exclusive. The main benefits of the Cedar Mill Celerons over the Prescott Celerons are the slightly increased performance due to the larger L2 cache, higher clock rates, and less heat dissipation, with several models having a TDP lowered to 65 W from Prescott's lowest offering of 73 W. In Intel's "Family/Model/Stepping" scheme, Cedar Mill Celeron Ds and Pentium 4s are family 15, model 6, and their Intel product code is 80552.Core-based Celerons
Conroe-L
The Conroe-L Celeron is a single-core processor built on the Core microarchitecture and is thus clocked much lower than the Cedar Mill Celerons, but still outperforms them. It is based on the 65 nm Conroe-L core, and uses a 400-series model number sequence. The FSB was increased to 800 MT/s from 533 MT/s in this generation, and the TDP was decreased from 65 W to 35 W. As is traditional with Celerons, it does not have Intel VT-x instruction support or SpeedStep (although Enhanced Halt State is enabled, allowing the Celerons to lower the multiplier to 6× and decrease core voltage while idle). All Conroe-L models are single-core processors for the value segment of the market, much like the AMD K8-based Sempron. The product line was launched on June 5, 2007. On October 21, 2007, Intel presented a new processor for its Intel Essential Series. The full name of the processor is Celeron 220 and is soldered on the D201GLY2 motherboard. With 1.2 GHz and a 512 KB L2 cache it has a TDP of 19 W and can be cooled passively. The Celeron 220 is the successor of the Celeron 215 which is based on a Yonah core and used on the D201GLY motherboard. This processor is exclusively used on the mini-ITX boards targeted to the sub-value market segment.Allendale
Intel launched the dual core Celeron E1xxx processor line on January 20, 2008, based on the Allendale core. The CPU has 800 MT/s FSB, 65 W TDP and uses 512 KB of the chip's 2 MB L2 cache, significantly limiting performance for uses such as gaming. New features to the Celeron family included full enhanced halt state and enhanced Intel SpeedStep technology. Clock rates range from 1.6 GHz to 2.4 GHz. It is compatible with other Allendale-based CPUs such as the Core 2 Duo E4xxx and Pentium Dual-Core E2xxx.Wolfdale-3M
The Celeron E3000 series, starting with E3200 and E3300, was released in August 2009, featuring the Wolfdale-3M core used in Pentium Dual-Core E5000, Pentium E6000 and Core 2 Duo E7000 series. The main difference to Allendale-based Celeron processors is the support for Intel VT-x and increased performance due to the double L2 Cache of 1 MB.Nehalem-based Celerons
Clarkdale
With the introduction of the Desktop Core i3 and Core i5 processor code named ''Clarkdale'' in January 2010, Intel also added a new Celeron line, starting with the Celeron G1101. This is the first Celeron to come with on-chip PCI Express and integrated graphics. Despite using the same Clarkdale chip as the Core i5-6xx line, it does not support Turbo Boost,Jasper Forest
The Celeron P1053 is an embedded processor for Socket 1366 from the ''Jasper Forest'' family. All other members of this family are known as Xeon C35xx or C55xx. The Jasper Forest chip is closely related to Lynnfield and contains four cores, 8 MB of L3 cache and a QPI interface, but most of these are disabled in the Celeron version, leaving a single core with 2 MB of L3 cache.Sandy Bridge-based desktop Celerons
The Sandy Bridge-based Celeron processors were released in 2011. They areIvy Bridge-based desktop Celerons
All Celerons of this generation belong in the G16xx series. They give some boost in performance over Sandy Bridge-based Celerons due to a 22 nm die shrink, as well as some other minor improvements.Haswell-based desktop Celerons
Skylake-based desktop Celerons
All Celerons of this generation added AES-NI and RDRAND instruction set.Kaby Lake-based desktop Celerons
Coffee Lake-based desktop Celerons
Comet Lake-based desktop Celerons
Mobile Celerons
P6-based mobile Celerons
Mendocino (mobile)
Similar to the Mendocino (Celeron-A): 0.25 μm, 32 KB L1 cache and 128 KB L2 cache, but uses a lower voltage (1.5–1.9 V) and two power-saving modes: Quick Start, and Deep Sleep. Packaged in the small, 615-pin BGA2 or Micro-PGA2 package.Tualatin-256 (mobile)
These were the first Mobile Celerons based on the Tualatin core. They differed from their desktop counterparts in that the Mobile series were offered in both 100 MHz and 133 MHz FSB. Like the desktop Tualatins, these chips had 256 KB of L2 cache.NetBurst-based mobile Celerons
Northwood-256
These are the Mobile Celeron range used in laptops. Also based on the Northwood core, they feature a 256 KB L2 cache. These Celeron processors were a good deal higher performing than the desktop counterparts because of their larger L2 cache sizes. They were eventually replaced by the Celeron M brand which is built around the Pentium M processor design.Pentium M-based mobile Celerons
Banias-512
This Celeron (sold under the Celeron M brand) is based on the ''Banias''Shelton
The ''Shelton'' core is a Banias core without ''any'' L2 cache and SpeedStep. It is used in Intel's small form factor D845GVSH motherboard, intended for Asian and South American markets. The processor identifies itself as a "Intel Celeron 1.0B GHz", to differentiate it from the previous Coppermine-128 and Tualatin 1.0 GHz processors. The Shelton'08 is a basic platform for a low cost notebook released by Intel at January 2008. The platform uses Intel's single-core Diamondville CPU with a clock frequency of 1.6 GHz and a 533 MT/s FSB and power consumption of 3.5 W. The platform's total power consumption is around 8 W, translating to battery usage time of between 3–4 hours. The platform consists of a 945GSE chipset, which includes built-in DirectX 9 graphics and supports single channel DDR2 memory. An 802.11g Wi-Fi module, USB/PATA port SSD (solid state drive), and a 7- or 8-inch panel will typically round out the platform.Dothan-1024
A 90 nm Celeron M with half of the L2 cache of the 90 nm ''Dothan'' Pentium Ms (twice the L2 cache of the 130 nm Celeron Ms, though), and, like its predecessor, lacking SpeedStep. The first Celeron Ms that supports the XD bit was released in January 2005, in general any Celeron M released after that supports the XD bit. There is also a 512 KB low voltage version that was used in the early ASUS Eee PC models. In Intel's "Family/Model/Stepping" scheme, Dothan Celeron Ms and Pentium Ms are family 6, model 13 and their Intel product code is 80536.Yonah
The Celeron M 400-series is a 65 nm Celeron M based on the single-core Yonah chip, like the Core Solo. Like its predecessors in the Celeron M series, this Celeron M has half of the L2 cache (1 MB) of Core Solo and lacks SpeedStep. This core also brings new features to Celeron M including a higher front side bus (533 MT/s), SSE3 instructions. September 2006 and January 4, 2008, mark a discontinuation of many ''Celeron M'' branded CPUs.Core-based mobile Celerons
Merom-L
The Celeron M 523 (933 MHz ULV), M 520 (1.6 GHz), M 530 (1.73 GHz), 530 (1.73 GHz), 540 (1.86 GHz), 550 (2.0 GHz), 560 (2.13 GHz), 570 (2.26 GHz) are single-core 65 nm CPUs based on the ''Merom'' Core 2 architecture. They feature a 533 MT/s FSB, 1 MB of L2 cache (half that of the low end Core 2 Duo's 2 MB cache), XD-bit support, and Intel 64 technology, but lack SpeedStep andMerom-2M
The Celeron 573 (1 GHz, ULV), 575 (2 GHz) and 585 (2.16 GHz) are based on the Merom-2M core with only one core and 1 MB L2 cache enabled. They are similar to the Merom and Merom-L based Celerons but have a faster 667 MT/s FSB. The Celeron T1xxx processors are also based on the Merom-2M chips but have both cores enabled. The earlier T1400 (1.73 GHz) and T1500 (1.86 GHz) versions have a 533 MT/s FSB and 512 B L2 cache, while the more recent T1600 (1.66 GHz) and T1700 (1.83 GHz) versions have 667 MT/s and 1 MB L2 cache enabled but come with a lower clock frequency.Penryn-3M
At the same time as the dual-core Merom-2M, Intel introduced the first 45 nm Celeron processor based on the Penryn-3M core with 800 MT/s FSB, 1 MB L2 cache and one core enabled. This includes the Celeron M 7xx Consumer Ultra-Low Voltage (CULV) series starting at 1.2 GHz and the later Celeron 900 (2.2 GHz). The initial 45 nm dual-core Celeron processor was released in June 2009 and is also based on Penryn-3M. The Celeron T3000 (1.8 GHz) and T3100 (1.9 GHz) again come with 1 MB of L2 cache enabled and an 800 MT/s FSB. In September 2009, Intel also started the dual-core CULV Celeron SU2000 series, again with 1 MB L2 cache. Despite the similar name, they are very different from Pentium SU2000 (with 2 MB L2 cache and one active core) and Pentium T3000 (based on the 65 nm Merom processor).Nehalem-based mobile Celerons
Arrandale
The Arrandale-based Celeron P4xxx and U3xxx lines are low-end versions of the Pentium P6xxx and U5xxx lines, originally released as the mobile dual-core lines of Core i3/i5/i7. Like the Clarkdale-based Celeron G1xxx, they use 2 MB of L3 cache, which is the amount that the earlier "Penryn" based CPUs used in the Pentium brand as their L2 cache. Like all Arrandale processors, the Celeron P4xxx and U3xxx use an integrated graphics core.Sandy Bridge-based mobile Celerons
The Celeron B8xx processors released in 2011 follow the Arrandale line. They are Dual-Core processors with integrated graphics and use the same chips as the Pentium B9xx and Core i3/i5/i7-2xxx mobile processors, but with Turbo-Boost, Hyper-Threading, VT-d, TXT and AES-NI disabled and the L3 cache reduced to 2MB.Dual-processor support
As a budget processor, the Celeron does not support a dual-processor configuration using multiple CPU sockets, however it has been discovered that multiprocessing could be enabled on Slot 1 Celeron processors by connecting a pin on the CPU core to a contact on the processor card's connector. In addition, Mendocino Socket 370 processors can use multiprocessing when used on specific dual Slot 1 motherboards by using a slot adapter. The unofficial SMP support was removed in the Coppermine Celerons, and dual-socket support is now limited to higher-end Xeon server-class processors. Conroe/Allendale based Celeron processors and later support multiprocessing using multi-core chips, but are still limited to one socket. TheSee also
* List of Intel Celeron processorsReferences
* * * * * * *External links