A coherent system of units is a system of

units of measurement A unit of measurement is a definite magnitude of a quantity, defined and adopted by convention or by law, that is used as a standard for measurement of the same kind of quantity. Any other quantity of that kind can be expressed as a multi ...

used to express physical quantities that are defined in such a way that the equations relating the numerical values expressed in the units of the system have exactly the same form, including numerical factors, as the corresponding equations directly relating the quantities. A coherent derived unit is a

derived unit SI derived units are units of measurement derived from the seven base units specified by the International System of Units (SI). They can be expressed as a product (or ratio) of one or more of the base units, possibly scaled by an appropriate ...

that, for a given system of quantities and for a chosen set of base units, is a product of powers of base units, with the proportionality factor being one. If a system of quantities has equations that relate quantities and the associated system of units has corresponding base units, with one base unit for each base quantity, then it is coherent if and only if every derived unit of the system is coherent. The concept of coherence was developed in the mid-nineteenth century by, amongst others,

Kelvin The kelvin, symbol K, is the primary unit of temperature in the International System of Units (SI), used alongside its prefixed forms and the degree Celsius. It is named after the Belfast-born and University of Glasgow-based engineer and phy ...

and

James Clerk Maxwell James Clerk Maxwell (13 June 1831 – 5 November 1879) was a Scottish mathematician and scientist responsible for the classical theory of electromagnetic radiation, which was the first theory to describe electricity, magnetism and li ...

and promoted by the

British Science Association The British Science Association (BSA) is a charity and learned society founded in 1831 to aid in the promotion and development of science. Until 2009 it was known as the British Association for the Advancement of Science (BA). The current Chie ...

. The concept was initially applied to the centimetre–gram–second (CGS) in 1873 and the

foot–pound–second system The foot–pound–second system or FPS system is a system of units built on three fundamental units: the foot for length, the (avoirdupois) pound for either mass or force (see below), and the second for time.. Variants Collectively, the varian ...

s (FPS) of units in 1875. The International System of Units (1960) was designed around the principle of coherence.

Example

In SI, which is a coherent system, the unit of power is the

watt The watt (symbol: W) is the unit of power or radiant flux in the International System of Units (SI), equal to 1 joule per second or 1 kg⋅m2⋅s−3. It is used to quantify the rate of energy transfer. The watt is named after James ...

, which is defined as one joule per second. In the

US customary system United States customary units form a system of measurement units commonly used in the United States and U.S. territories since being standardized and adopted in 1832. The United States customary system (USCS or USC) developed from English unit ...

of measurement, which is non-coherent, the unit of power is the

horsepower Horsepower (hp) is a unit of measurement of power, or the rate at which work is done, usually in reference to the output of engines or motors. There are many different standards and types of horsepower. Two common definitions used today are t ...

, which is defined as 550 foot-pounds per second (the pound in this context being the pound-force); similarly the gallon is 231 cubic inches.

Before the metric system

The earliest units of measure devised by humanity bore no relationship to each other. As both humanity's understanding of

philosophical concepts Philosophy (from , ) is the systematized study of general and fundamental questions, such as those about existence, reason, knowledge, values, mind, and language. Such questions are often posed as problems to be studied or resolved. Some s ...

and the organisation of

society A society is a group of individuals involved in persistent social interaction, or a large social group sharing the same spatial or social territory, typically subject to the same political authority and dominant cultural expectations. Soci ...

developed, so units of measurement were standardised – first particular units of measure had the same value across a

community A community is a social unit (a group of living things) with commonality such as place, norms, religion, values, customs, or identity. Communities may share a sense of place situated in a given geographical area (e.g. a country, village, ...

, then different units of the same

quantity Quantity or amount is a property that can exist as a multitude or magnitude, which illustrate discontinuity and continuity. Quantities can be compared in terms of "more", "less", or "equal", or by assigning a numerical value multiple of a unit ...

(for example feet and inches) were given a fixed relationship. Apart from Ancient China where the units of capacity and of mass were linked to red millet seed, there is little evidence of the linking of different quantities until the Enlightenment.

Relating quantities of the same kind

The history of the measurement of length dates back to the early civilisations of the

Middle East The Middle East ( ar, الشرق الأوسط, ISO 233: ) is a geopolitical region commonly encompassing Arabia (including the Arabian Peninsula and Bahrain), Asia Minor (Asian part of Turkey except Hatay Province), East Thrace (Europ ...

(10000 BC – 8000 BC). Archeologists have been able to reconstruct the units of measure in use in

Mesopotamia Mesopotamia ''Mesopotamíā''; ar, بِلَاد ٱلرَّافِدَيْن or ; syc, ܐܪܡ ܢܗܪ̈ܝܢ, or , ) is a historical region of Western Asia situated within the Tigris–Euphrates river system, in the northern part of the ...

India India, officially the Republic of India (Hindi: ), is a country in South Asia. It is the seventh-largest country by area, the second-most populous country, and the most populous democracy in the world. Bounded by the Indian Ocean on the so ...

, the Jewish culture and many others. Archeological and other evidence shows that in many civilisations, the ratios between different units for the same quantity of measure were adjusted so that they were integer numbers. In many early cultures such as Ancient Egypt, multiples of 2, 3 and 5 were not always used—the Egyptian royal cubit being 28 fingers or 7 hands. In 2150 BC, the

Akkadian Akkadian or Accadian may refer to: * Akkadians, inhabitants of the Akkadian Empire * Akkadian language, an extinct Eastern Semitic language * Akkadian literature, literature in this language * Akkadian cuneiform Cuneiform is a logo- syllabi ...

emperor Naram-Sin rationalised the Babylonian system of measure, adjusting the ratios of many units of measure to multiples of 2, 3 or 5, for example there were 6 ''she'' (

barley Barley (''Hordeum vulgare''), a member of the grass family, is a major cereal grain grown in temperate climates globally. It was one of the first cultivated grains, particularly in Eurasia as early as 10,000 years ago. Globally 70% of barley p ...

corns) in a ''shu-si'' (

finger A finger is a limb of the body and a type of digit, an organ of manipulation and sensation found in the hands of most of the Tetrapods, so also with humans and other primates. Most land vertebrates have five fingers ( Pentadactyly). Chambers ...

) and 30 shu-si in a ''kush'' (

cubit The cubit is an ancient unit of length based on the distance from the elbow to the tip of the middle finger. It was primarily associated with the Sumerians, Egyptians, and Israelites. The term ''cubit'' is found in the Bible regarding ...

Relating quantities of different kinds

Non- commensurable quantities have different physical dimensions, which means that adding or subtracting them is not meaningful. For instance, adding the

mass Mass is an intrinsic property of a body. It was traditionally believed to be related to the quantity of matter in a physical body, until the discovery of the atom and particle physics. It was found that different atoms and different eleme ...

of an object to its

volume Volume is a measure of occupied three-dimensional space. It is often quantified numerically using SI derived units (such as the cubic metre and litre) or by various imperial or US customary units (such as the gallon, quart, cubic inch). Th ...

has no physical meaning. However, new quantities (and, as such, units) can be

derived Derive may refer to: * Derive (computer algebra system), a commercial system made by Texas Instruments * ''Dérive'' (magazine), an Austrian science magazine on urbanism *Dérive, a psychogeographical concept See also * *Derivation (disambiguatio ...

via multiplication and

exponentiation Exponentiation is a mathematical operation, written as , involving two numbers, the '' base'' and the ''exponent'' or ''power'' , and pronounced as " (raised) to the (power of) ". When is a positive integer, exponentiation corresponds to r ...

of other units. As an example, the

SI unit The International System of Units, known by the international abbreviation SI in all languages and sometimes pleonastically as the SI system, is the modern form of the metric system and the world's most widely used system of measurement. ...

for force is the newton, which is defined as kg⋅m⋅s⁻². Since a coherent derived unit is one which is defined by means of multiplication and exponentiation of other units but not multiplied by any scaling factor other than 1, the pascal is a coherent unit of

pressure Pressure (symbol: ''p'' or ''P'') is the force applied perpendicular to the surface of an object per unit area over which that force is distributed. Gauge pressure (also spelled ''gage'' pressure)The preferred spelling varies by country and e ...

(defined as kg⋅m⁻¹⋅s⁻²), but the

bar Bar or BAR may refer to: Food and drink * Bar (establishment), selling alcoholic beverages * Candy bar * Chocolate bar Science and technology * Bar (river morphology), a deposit of sediment * Bar (tropical cyclone), a layer of cloud * Bar (u ...

(defined as ) is not. Note that coherence of a given unit depends on the definition of the base units. Should the standard unit of length change such that it is shorter by a factor of , then the bar would be a coherent derived unit. However, a coherent unit remains coherent (and a non-coherent unit remains non-coherent) if the base units are redefined in terms of other units with the numerical factor always being unity.

Metric system

Rational system and use of water

The concept of coherence was only introduced into the metric system in the third quarter of the nineteenth century; in its original form the metric system was non-coherent – in particular the

litre The litre (international spelling) or liter (American English spelling) (SI symbols L and l, other symbol used: ℓ) is a metric unit of volume. It is equal to 1 cubic decimetre (dm3), 1000 cubic centimetres (cm3) or 0.001 cubic metre (m3 ...

was 0.001 m³ and the are (from which we get the

hectare The hectare (; SI symbol: ha) is a non-SI metric unit of area equal to a square with 100- metre sides (1 hm2), or 10,000 m2, and is primarily used in the measurement of land. There are 100 hectares in one square kilometre. An acre is ...

) was 100 m². A precursor to the concept of coherence was however present in that the units of mass and length were related to each other through the physical properties of water, the gram having been designed as being the mass of one cubic centimetre of water at its freezing point. The CGS system had two units of energy, the

erg The erg is a unit of energy equal to 10−7joules (100 nJ). It originated in the Centimetre–gram–second system of units (CGS). It has the symbol ''erg''. The erg is not an SI unit. Its name is derived from (), a Greek word meaning 'work' o ...

that was related to

mechanics Mechanics (from Ancient Greek: μηχανική, ''mēkhanikḗ'', "of machines") is the area of mathematics and physics concerned with the relationships between force, matter, and motion among physical objects. Forces applied to object ...

and the calorie that was related to

thermal energy The term "thermal energy" is used loosely in various contexts in physics and engineering. It can refer to several different well-defined physical concepts. These include the internal energy or enthalpy of a body of matter and radiation; heat, de ...

, so only one of them (the erg, equivalent to the g⋅cm²/s²) could bear a coherent relationship to the base units. By contrast, coherence was a design aim of the SI, resulting in only one unit of energy being defined – the

joule The joule ( , ; symbol: J) is the unit of energy in the International System of Units (SI). It is equal to the amount of work done when a force of 1 newton displaces a mass through a distance of 1 metre in the direction of the force applie ...

Dimension-related coherence

Work of

and others Each variant of the metric system has a degree of coherence – the various derived units being directly related to the base units without the need of intermediate conversion factors. An additional criterion is that, for example, in a coherent system the units of force,

energy In physics, energy (from Ancient Greek: ἐνέργεια, ''enérgeia'', “activity”) is the quantitative property that is transferred to a body or to a physical system, recognizable in the performance of work and in the form of hea ...

and

power Power most often refers to: * Power (physics), meaning "rate of doing work" ** Engine power, the power put out by an engine ** Electric power * Power (social and political), the ability to influence people or events ** Abusive power Power may a ...

be chosen so that the equations :' = ' × ' :' = ' × ' :' = ' / ' hold without the introduction of constant factors. Once a set of coherent units have been defined, other relationships in physics that use those units will automatically be true – Einstein's mass–energy equation, , does not require extraneous constants when expressed in coherent units. Isaac Asimov wrote, "In the cgs system, a unit force is described as one that will produce an acceleration of 1 cm/sec² on a mass of 1 gm. A unit force is therefore 1 cm/sec² multiplied by 1 gm." These are independent statements. The first is a definition; the second is not. The first implies that the constant of proportionality in the force law has a magnitude of one; the second implies that it is dimensionless. Asimov uses them both together to prove that it is the pure number one. Asimov's conclusion is not the only possible one. In a system that uses the units foot (ft) for length, second (s) for time, pound (lb) for mass, and pound-force (lbf) for force, the law relating force (''F''), mass (''m''), and acceleration (''a'') is . Since the proportionality constant here is dimensionless and the units in any equation must balance without any numerical factor other than one, it follows that 1 lbf = 1 lb⋅ft/s². This conclusion appears paradoxical from the point of view of competing systems, according to which and . Although the pound-force is a coherent derived unit in this system according to the official definition, the system itself is not considered to be coherent because of the presence of the proportionality constant in the force law. A variant of this system applies the unit s²/ft to the proportionality constant. This has the effect of identifying the pound-force with the pound. The pound is then both a base unit of mass and a coherent derived unit of force. One may apply any unit one pleases to the proportionality constant. If one applies the unit s²/lb to it, then the foot becomes a unit of force. In a four-unit system (

English engineering units Some fields of engineering in the United States use a system of measurement of physical quantities known as the English Engineering Units. Despite its name, the system is based on United States customary units of measure; it is not used in England ...

), the pound and the pound-force are distinct base units, and the proportionality constant has the unit lbf⋅s²/(lb⋅ft). All these systems are coherent. One that is not is a three-unit system (also called English engineering units) in which ''F'' = ''ma'' that uses the pound and the pound-force, one of which is a base unit and the other, a noncoherent derived unit. In place of an explicit proportionality constant, this system uses conversion factors derived from the relation 1 lbf = 32.174 lb⋅ft/s². In numerical calculations, it is indistinguishable from the four-unit system, since what is a proportionality constant in the latter is a conversion factor in the former. The relation among the numerical values of the quantities in the force law is = 0.031081 , where the braces denote the numerical values of the enclosed quantities. Unlike in this system, in a coherent system, the relations among the numerical values of quantities are the same as the relations among the quantities themselves. The following example concerns definitions of quantities and units. The (average) velocity (''v'') of an object is defined as the quantitative physical property of the object that is directly proportional to the distance (''d'') traveled by the object and inversely proportional to the time (''t'') of travel, i.e., ''v'' = ''kd''/''t'', where ''k'' is a constant that depends on the units used. Suppose that the metre (m) and the second (s) are base units; then the kilometer (km) and the hour (h) are noncoherent derived units. The metre per second (mps) is defined as the velocity of an object that travels one metre in one second, and the kilometer per hour (kmph) is defined as the velocity of an object that travels one kilometre in one hour. Substituting from the definitions of the units into the defining equation of velocity we obtain, 1 mps = ''k'' m/s and 1 kmph = ''k'' km/h = 1/3.6 ''k'' m/s = 1/3.6 mps. Now choose ''k'' = 1; then the metre per second is a coherent derived unit, and the kilometre per hour is a noncoherent derived unit. Suppose that we choose to use the kilometre per hour as the unit of velocity in the system. Then the system becomes noncoherent, and the numerical value equation for velocity becomes = 3.6 /. Coherence may be restored, without changing the units, by choosing ''k'' = 3.6; then the kilometre per hour is a coherent derived unit, with 1 kmph = 1 m/s, and the metre per second is a noncoherent derived unit, with 1 mps = 3.6 m/s. A definition of a physical quantity is a statement that determines the ratio of any two instances of the quantity. The specification of the value of any constant factor is not a part of the definition since it does not affect the ratio. The definition of velocity above satisfies this requirement since it implies that ''v''₁/''v''₂ = (''d''₁/''d''₂)/(''t''₁/''t''₂); thus if the ratios of distances and times are determined, then so is the ratio of velocities. A definition of a unit of a physical quantity is a statement that determines the ratio of any instance of the quantity to the unit. This ratio is the numerical value of the quantity or the number of units contained in the quantity. The definition of the metre per second above satisfies this requirement since it, together with the definition of velocity, implies that ''v''/mps = (''d''/m)/(''t''/s); thus if the ratios of distance and time to their units are determined, then so is the ratio of velocity to its unit. The definition, by itself, is inadequate since it only determines the ratio in one specific case; it may be thought of as exhibiting a specimen of the unit. A new coherent unit cannot be defined merely by expressing it algebraically in terms of already defined units. Thus the statement, "the metre per second equals one metre divided by one second", is not, by itself, a definition. It does not imply that a unit of velocity is being defined, and if that fact is added, it does not determine the magnitude of the unit, since that depends on the system of units. In order for it to become a proper definition both the quantity and the defining equation, including the value of any constant factor, must be specified. After a unit has been defined in this manner, however, it has a magnitude that is independent of any system of units.

Catalogue of coherent relations

This list catalogues coherent relationships in various systems of units.

SI

The following is a list of coherent SI units: :

frequency Frequency is the number of occurrences of a repeating event per unit of time. It is also occasionally referred to as ''temporal frequency'' for clarity, and is distinct from ''angular frequency''. Frequency is measured in hertz (Hz) which is eq ...

(

hertz The hertz (symbol: Hz) is the unit of frequency in the International System of Units (SI), equivalent to one event (or cycle) per second. The hertz is an SI derived unit whose expression in terms of SI base units is s−1, meaning that o ...

) =

reciprocal Reciprocal may refer to: In mathematics * Multiplicative inverse, in mathematics, the number 1/''x'', which multiplied by ''x'' gives the product 1, also known as a ''reciprocal'' * Reciprocal polynomial, a polynomial obtained from another pol ...

of time (

inverse second The inverse second or reciprocal second (s−1) is a unit of frequency, defined as the multiplicative inverse of the second (a unit of time). It is dimensionally equivalent to: * the unit hertz – the SI unit for frequency * the unit radian per ...

s) : force ( newtons) = mass (kilograms) × acceleration (m/s²) :

(

pascals The pascal (symbol: Pa) is the unit of pressure in the International System of Units (SI), and is also used to quantify internal pressure, stress, Young's modulus, and ultimate tensile strength. The unit, named after Blaise Pascal, is defined ...

) = force (newtons) ÷

area Area is the quantity that expresses the extent of a region on the plane or on a curved surface. The area of a plane region or ''plane area'' refers to the area of a shape or planar lamina, while '' surface area'' refers to the area of an ope ...

(m²) :

(

s) = force (newtons) × distance (metres) :

(

s) = energy (joules) ÷ time (seconds) :

potential difference Voltage, also known as electric pressure, electric tension, or (electric) potential difference, is the difference in electric potential between two points. In a static electric field, it corresponds to the work needed per unit of charge to m ...

(

volt The volt (symbol: V) is the unit of electric potential, electric potential difference (voltage), and electromotive force in the International System of Units (SI). It is named after the Italian physicist Alessandro Volta (1745–1827). Defin ...

s) = power (watts) ÷ electric current (amps) :

electric charge Electric charge is the physical property of matter that causes charged matter to experience a force when placed in an electromagnetic field. Electric charge can be ''positive'' or ''negative'' (commonly carried by protons and electrons respe ...

( coulombs) = electric current (amps) × time (seconds) : equivalent radiation dose (

sievert The sievert (symbol: SvNot be confused with the sverdrup or the svedberg, two non-SI units that sometimes use the same symbol.) is a unit in the International System of Units (SI) intended to represent the stochastic health risk of ionizing rad ...

s) = energy (joules) ÷ mass (kilograms) : absorbed radiation dose (

gray Grey (more common in British English) or gray (more common in American English) is an intermediate color between black and white. It is a neutral or achromatic color, meaning literally that it is "without color", because it can be composed o ...

s) = energy (joules) ÷ mass (kilograms) : radioactive activity (

becquerel The becquerel (; symbol: Bq) is the unit of radioactivity in the International System of Units (SI). One becquerel is defined as the activity of a quantity of radioactive material in which one nucleus decays per second. For applications relatin ...

s) = reciprocal of time (s⁻¹) :

capacitance Capacitance is the capability of a material object or device to store electric charge. It is measured by the change in charge in response to a difference in electric potential, expressed as the ratio of those quantities. Commonly recognized ar ...

( farads) = electric charge (coulombs) ÷ potential difference (volts) :

electrical resistance The electrical resistance of an object is a measure of its opposition to the flow of electric current. Its reciprocal quantity is , measuring the ease with which an electric current passes. Electrical resistance shares some conceptual paralle ...

(

ohm Ohm (symbol Ω) is a unit of electrical resistance named after Georg Ohm. Ohm or OHM may also refer to: People * Georg Ohm (1789–1854), German physicist and namesake of the term ''ohm'' * Germán Ohm (born 1936), Mexican boxer * Jörg Ohm (b ...

s) = potential difference (volts) ÷ electric current (amperes) :

electrical conductance The electrical resistance of an object is a measure of its opposition to the flow of electric current. Its reciprocal quantity is , measuring the ease with which an electric current passes. Electrical resistance shares some conceptual paralle ...

( siemens) = electric current (amperes) ÷ potential difference (volts) : magnetic flux ( weber) = potential difference (

s) × time (seconds) :

magnetic flux density A magnetic field is a vector field that describes the magnetic influence on moving electric charges, electric currents, and magnetic materials. A moving charge in a magnetic field experiences a force perpendicular to its own velocity and to ...

( tesla) = magnetic flux (webers) ÷ area (square metres)

CGS

The following is a list of coherent centimetre–gram–second (CGS) system of units: :

acceleration In mechanics, acceleration is the rate of change of the velocity of an object with respect to time. Accelerations are vector quantities (in that they have magnitude and direction). The orientation of an object's acceleration is given by t ...

( gals) = distance (centimetres) ÷ time² (s²) :force (

dyne The dyne (symbol: dyn; ) is a derived unit of force specified in the centimetre–gram–second (CGS) system of units, a predecessor of the modern SI. History The name dyne was first proposed as a CGS unit of force in 1873 by a Committee of ...

s) = mass (grams) × acceleration (cm/s²) :energy (

s) = force (dynes) × distance (centimetres) :pressure (

barye The barye (symbol: Ba), or sometimes barad, barrie, bary, baryd, baryed, or barie, is the centimetre–gram–second (CGS) unit of pressure. It is equal to 1 dyne per square centimetre. : = = = = = See also *Pasca ...

) = force (dynes) ÷

(cm²) :dynamic

viscosity The viscosity of a fluid is a measure of its resistance to deformation at a given rate. For liquids, it corresponds to the informal concept of "thickness": for example, syrup has a higher viscosity than water. Viscosity quantifies the inte ...

( poise) = mass (grams) ÷ (distance (centimetres) × time (seconds)) :kinematic

( stokes) = area (cm²) ÷ time (seconds)

FPS

The following is a list of coherent foot–pound–second (FPS) system of units: :force (poundal) = mass (pounds) × acceleration (ft/s²)

References

{{DEFAULTSORT:Coherent units of measurement Systems of units Dimensional analysis