|
Recoil Start
Rope start (also called ripcord , ''pull start'', or ''rewind start'') is a method of starting an internal combustion engine, usually on small machines, such as lawn mowers, chainsaws, grass trimmers, ultralight aircraft, small outboard motors and portable engine-generators. Also used on some small vehicles such as small go-karts, minibikes, and small ATVs. Recoil start This starter mechanism comprises a rope, with a grip at the end, moulded rope reels and a spring. The rope is coiled within a reel which is held under spring tension within an outer reel. This reel assembly is in contact with one end of the crankshaft A crankshaft is a mechanical component used in a reciprocating engine, piston engine to convert the reciprocating motion into rotational motion. The crankshaft is a rotating Shaft (mechanical engineering), shaft containing one or more crankpins, ... through a ratcheting mechanism (specifically, a ''freewheel clutch''). When the rope's grip is pulled, t ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Minibikes
A minibike is a two-wheeled, motorized, off-highway recreational vehicle popularized in the 1960s and 1970s, but available continuously from a wide variety of manufacturers since 1959. Their off-highway nature and (in many countries) typically entirely off-road legal status differentiate minibikes from motorcycles and mopeds, and their miniature size differentiates them from dirt bikes. Traditionally, minibikes have a four-stroke, horizontal crankshaft engine, single- or two-speed centrifugal clutch semi-automatic transmission, transmissions with chain final-drive, wheels and a low frame/seat height with elevated handlebars. Commercially available minibikes are usually equipped with small engines commonly found elsewhere on utilitarian equipment such as garden tillers. History While the minibike had precursors in machines such as the Doodle Bug scooter, Doodle Bug and Cushman Scooters, which share smaller wheels, tubular-steel frames, and air-cooled, single-cylinder engines, ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Compression Release
A compression release mechanism works to ease the starting of internal combustion engines by allowing them to rotate to starting speed without having to work against the compression of the pistons. It does this via either a release valve that is incorporated within the cylinder head that vents the cylinder pressure to the outside atmosphere until the engine has sufficient Angular momentum, momentum to overcome it, or by venting straight through one of the main valves. US patent US5375570 A of 1994 describes an automated compression release valve actuated by engine oil pressure. Motorcycles Early large displacement motorcycles with kick starters provided riders with a manual compression release while later models linked them to the kick start lever with a cable for automatic operation. The 2012 Ducati 1199, equipped with an electric starter, uses a compression release that is automatically activated at low engine speed by a centrifugal flyweight on each exhaust cam. This reduces th ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Jacobsen Manufacturing
Jacobsen Manufacturing is a former U.S. lawn mower and light-duty tractor manufacturer, in operation there from the early 1920s until around 2020. It was located in Racine, Wisconsin, from 1921 to 2001, when It moved to Charlotte, North Carolina. In 2017, Jacobsen moved from Charlotte to Augusta, Georgia. In 2020, it would relocate to its sister factory of Ransomes-Jacobsen in Ipswich, England, UK. It has been owned by Textron since 1975. History Jacobsen Manufacturing was founded around the turn of the 20th century as a pattern-making shop by Knud Jacobsen, a Danish immigrant who came to Racine, Wisconsin, in 1891. A skilled woodworker, Jacobsen made patterns for automobiles, agricultural machines and electrical equipment. Jacobsen restructured his business as Thor Machine Works in 1917. In 1921 it released the 4-Acre mower, a gasoline-powered reel mower marketed through Jacobsen Manufacturing. Not long after the Greens Mower was released. In 1928 Jacobsen made a notable contri ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Freewheel
image:Freewheel en.svg, Freewheel mechanism In mechanical engineering, mechanical or automotive engineering, a freewheel or overrunning clutch is a device in a transmission (mechanics), transmission that disengages the driveshaft from the driven shaft when the driven shaft rotates faster than the driveshaft. An Overdrive (mechanics), overdrive is sometimes mistakenly called a freewheel, but is otherwise unrelated. The condition of a driven shaft spinning faster than its driveshaft exists in most bicycles when the rider stops Bicycle pedal, pedaling. In a fixed-gear bicycle, without a freewheel, the rear wheel drives the pedals around. An analogous condition exists in an automobile with a manual transmission going downhill, or any situation where the driver takes their foot off the Car controls#Throttle control, gas pedal, closing the throttle: the wheels drive the engine, possibly at a higher RPM. In a two-stroke engine, this can be catastrophic—as many two stroke engines de ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Ratchet (device)
A ratchet (occasionally spelled rachet) is a mechanical device that allows continuous linear or rotary motion in only one direction while preventing motion in the opposite direction. Ratchets are widely used in machinery and tools. The word ''ratchet'' is also used informally to refer to a ratcheting socket wrench. __TOC__ Theory of operation A ratchet consists of a round gear or a linear rack with teeth, and a pivoting, spring-loaded finger called a '' pawl'' (or ''click'', in clocks and watches) that engages the teeth. The teeth are uniform but are usually asymmetrical, with each tooth having a moderate slope on one edge and a much steeper slope on the other edge. When the teeth are moving in the unrestricted (i.e. forward) direction, the pawl easily slides up and over the gently sloped edges of the teeth, with a spring forcing it (often with an audible 'click') into the depression between the teeth as it passes the tip of each tooth. When the teeth move in the oppo ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Crankshaft
A crankshaft is a mechanical component used in a reciprocating engine, piston engine to convert the reciprocating motion into rotational motion. The crankshaft is a rotating Shaft (mechanical engineering), shaft containing one or more crankpins, that are driven by the pistons via the connecting rods. The crankpins are also called ''rod bearing journals'', and they rotate within the "big end" of the connecting rods. Most modern crankshafts are located in the engine block. They are made from steel or cast iron, using either a forging, casting (metalworking), casting or machining process. Design The crankshaft is located within the engine block and held in place via main bearings which allow the crankshaft to rotate within the block. The up-down motion of each piston is transferred to the crankshaft via connecting rods. A flywheel is often attached to one end of the crankshaft, in order to smoothen the power delivery and reduce vibration. A crankshaft is subjected to enormou ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
All-terrain Vehicle
An all-terrain vehicle (ATV), also known as a light utility vehicle (LUV), a quad bike or quad (if it has four wheels), as defined by the American National Standards Institute (ANSI), is a vehicle that travels on low-pressure tires, has a seat that is straddled by the operator, and has handlebars, similar to a motorcycle. As the name implies, it is designed to handle a wider variety of terrain than most other vehicles. It is street-legal in some countries, but not in most states, territories and provinces of Australia, the United States, and Canada. By the current ANSI definition, ATVs are intended for use by a single operator, but some ATVs, referred to as tandem ATVs, have been developed for use by the driver and one passenger. The rider sits on and operates these vehicles like a motorcycle, but the extra wheels give more stability at slower speeds. Although most are equipped with three or four wheels, six or eight wheel (tracked) models exist and have existed historicall ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Go-kart
A go-kart, also written as go-cart (often referred to as simply a kart), is a type of small sports car, close wheeled car, open-wheel car or quadracycle. Go-karts come in all shapes and forms, from non-motorised models to high-performance racing karts. Karting is a type of racing in which a compact four-wheel unit called a go-kart is used. Art Ingels created the first go-kart in Los Angeles in 1956. Etymology The exact origin of the term is unclear. One of the first appearances of the term is an 1885 painting by the Scottish artist Hugh Cameron's "The Go-Cart". It is also unclear why the ''C'' was later changed to a ''K''. In the film ''The Ivory-Handled Gun'' (1935), the crippled father of Buck Jones refers to his wheelchair as a "go cart". Charles Dickens also used ''go-cart'' in '' Master Humphrey's Clock and Other Stories'' when talking of his travel to Italy. In Genoa, he talks about "a man without legs, on a little go-cart". Non-motorised Gravity racers are a po ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Jumo 004
The Junkers Jumo 004 was the world's first production turbojet engine in operational use, and the first successful axial compressor turbojet engine. Some 8,000 units were manufactured by Junkers in Germany late in World War II, powering the Messerschmitt Me 262 fighter and the Arado Ar 234 reconnaissance/bomber, along with prototypes, including the Horten Ho 229. Variants and copies of the engine were produced in Eastern Europe and the USSR for several years following the end of WWII. Design and development The feasibility of jet propulsion had been demonstrated in Germany in early 1937 by Hans von Ohain working with the Heinkel company. Most of the Reich Air Ministry ( RLM) remained uninterested, but Helmut Schelp and Hans Mauch saw the potential of the concept and encouraged Germany's aero engine manufacturers to begin their own programmes of jet engine development. The companies remained skeptical and little new development was carried out. In 1939 Schelp and Mauch visited ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Outboard Motors
An outboard motor is a propulsion system for boats, consisting of a self-contained unit that includes engine, gearbox and propeller or jet drive, designed to be affixed to the outside of the transom. They are the most common motorised method of propelling small watercraft. As well as providing propulsion, outboards provide steering control, as they are designed to pivot over their mountings and thus control the direction of thrust. The skeg also acts as a rudder when the engine is not running. Unlike inboard motors, outboard motors can be easily removed for storage or repairs. In order to eliminate the chances of hitting bottom with an outboard motor, the motor can be tilted up to an elevated position either electronically or manually. This helps when traveling through shallow waters where there may be debris that could potentially damage the motor as well as the propeller. If the electric motor required to move the pistons which raise or lower the engine is malfunction ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
