|
Permeability (foundry Sand)
Permeability is a property of foundry sand with respect to how well the sand can vent, ''i.e.'' how well gases pass through the sand. And in other words, permeability is the property by which we can know the ability of material to transmit fluid/gases. The permeability is commonly tested to see if it is correct for the casting conditions. Affecting factors The grain size, shape and distribution of the foundry sand, the type and quantity of bonding materials, the density to which the sand is rammed, and the percentage of moisture used for tempering the sand are important factors in regulating the degree of permeability. Significance An increase in permeability usually indicates a more open structure in the rammed sand, and if the increase continues, it will lead to penetration-type defects and rough castings. A decrease in permeability indicates tighter packing and could lead to blows and pinholes. Testing procedure * On a prepared mould surface as a sample, permeability can be ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Foundry Sand
Molding sand, also known as foundry sand, is a sand that when moistened and compressed or oiled or heated tends to pack well and hold its shape. It is used in the process of sand casting for preparing the mold cavity. Green sand Green sand is an aggregate of sand, bentonite clay, pulverized coal and water. Its principal use is in making molds for metal casting. The largest portion of the aggregate is a sand, either most-commonly silica or sometimes olivine. There are many recipes for the proportion of clay, but they all strike different balances between moldability, surface finish, and ability of the hot molten metal to degas. The coal, typically referred to in as sea-coal, which is present at a ratio of less than 5%, partially combusts in the surface of the molten metal leading to offgassing of organic vapors. Sand casting is one of the earliest forms of casting practiced due to the simplicity of materials involved. It still remains one of the cheapest ways to cast metals beca ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Casting
Casting is a manufacturing process in which a liquid material is usually poured into a mold, which contains a hollow cavity of the desired shape, and then allowed to solidify. The solidified part is also known as a ''casting'', which is ejected or broken out of the mold to complete the process. Casting materials are usually metals or various ''time setting'' materials that cure after mixing two or more components together; examples are epoxy, concrete, plaster and clay. Casting is most often used for making complex shapes that would be otherwise difficult or uneconomical to make by other methods. Heavy equipment like machine tool beds, ships' propellers, etc. can be cast easily in the required size, rather than fabricating by joining several small pieces. Casting is a 7,000-year-old process. The oldest surviving casting is a copper frog from 3200 BC. History Throughout history, metal casting has been used to make tools, weapons, and religious objects. Metal casting history and de ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Grain Size
Grain size (or particle size) is the diameter of individual grains of sediment, or the lithified particles in clastic rocks. The term may also be applied to other granular materials. This is different from the crystallite size, which refers to the size of a single crystal inside a particle or grain. A single grain can be composed of several crystals. Granular material can range from very small colloidal particles, through clay, silt, sand, gravel, and cobbles, to boulders. Krumbein phi scale Size ranges define limits of classes that are given names in the Wentworth scale (or Udden–Wentworth scale) used in the United States. The Krumbein ''phi'' (φ) scale, a modification of the Wentworth scale created by W. C. Krumbein in 1934, is a logarithmic scale computed by the equation :\varphi=-\log_2, where :\varphi is the Krumbein phi scale, :D is the diameter of the particle or grain in millimeters (Krumbein and Monk's equation) and :D_0 is a reference diameter, equal to 1 ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Volumetric Flow Rate
In physics and engineering, in particular fluid dynamics, the volumetric flow rate (also known as volume flow rate, or volume velocity) is the volume of fluid which passes per unit time; usually it is represented by the symbol (sometimes ). It contrasts with mass flow rate, which is the other main type of fluid flow rate. In most contexts a mention of ''rate of fluid flow'' is likely to refer to the volumetric rate. In hydrometry, the volumetric flow rate is known as '' discharge''. Volumetric flow rate should not be confused with volumetric flux, as defined by Darcy's law and represented by the symbol , with units of m3/(m2·s), that is, m·s−1. The integration of a flux over an area gives the volumetric flow rate. The SI unit is cubic metres per second (m3/s). Another unit used is standard cubic centimetres per minute (SCCM). In US customary units and imperial units, volumetric flow rate is often expressed as cubic feet per second (ft3/s) or gallons per minute (either ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Standard Conditions For Temperature And Pressure
Standard temperature and pressure (STP) are standard sets of conditions for experimental measurements to be established to allow comparisons to be made between different sets of data. The most used standards are those of the International Union of Pure and Applied Chemistry (IUPAC) and the National Institute of Standards and Technology (NIST), although these are not universally accepted standards. Other organizations have established a variety of alternative definitions for their standard reference conditions. In chemistry, IUPAC changed its definition of standard temperature and pressure in 1982: * Until 1982, STP was defined as a temperature of 273.15 K (0 °C, 32 °F) and an absolute pressure of exactly 1 atm (101.325 kPa). * Since 1982, STP has been defined as a temperature of 273.15 K (0 °C, 32 °F) and an absolute pressure of exactly 105 Pa (100 kPa, 1 bar). STP should not be confused with the standard state com ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
American Foundry Society
The American Foundry Society (AFS) is a professional, technical and trade association for foundries and the broader metal casting industry. The society promotes the interests of foundries to policymakers, provides training for foundry workers, and supports research and technological advancements in foundry science and manufacturing. AFS represents ferrous and nonferrous foundries based in North America, as well as industry suppliers and end-users of metal castings from around the world. The society has individual and corporate members across 48 countries, organized into regional chapters and student chapters in the United States, Canada and Mexico. AFS presents Metalcasting Congress, a yearly industry conference, as well as CastExpo, a trade show and exposition that occurs every three years. AFS is based in Schaumburg, Illinois, and also maintains an office in Washington, D.C. Doug Kurkul is CEO of the organization. History The American Foundry Society traces its roots to 1896 ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Ramming
In warfare, ramming is a technique used in air, sea, and land combat. The term originated from battering ram, a siege weapon used to bring down fortifications by hitting it with the force of the ram's momentum, and ultimately from male sheep. Thus, in warfare, ramming refers to hitting a target by running oneself into the target. Today, hand-held battering rams are one tool among many used by law enforcement and military personnel for door breaching. Forcible entry by criminals has been implemented using such methods as Ram-raiding, vehicles rammed into buildings. Naval warfare Navies in antiquity commonly used the ram: the "beak" ( la , rostrum) became an important part of the armament of the galleys of Imperial Rome. The Ancient Greece, ancient Greeks used their trireme vessels for ramming as well. In History of China#Ancient China, ancient China, rams were largely unknown, as the lack of a keel and the flat shape of the junk (ship), junk's bow was not conducive to constructi ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Casting (manufacturing)
Casting is a manufacturing process in which a liquid material is usually poured into a mold, which contains a hollow cavity of the desired shape, and then allowed to solidify. The solidified part is also known as a ''casting'', which is ejected or broken out of the mold to complete the process. Casting materials are usually metals or various ''time setting'' materials that cure after mixing two or more components together; examples are epoxy, concrete, plaster and clay. Casting is most often used for making complex shapes that would be otherwise difficult or uneconomical to make by other methods. Heavy equipment like machine tool beds, ships' propellers, etc. can be cast easily in the required size, rather than fabricating by joining several small pieces. Casting is a 7,000-year-old process. The oldest surviving casting is a copper frog from 3200 BC. History Throughout history, metal casting has been used to make tools, weapons, and religious objects. Metal casting history and de ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
