|
Media Redundancy Protocol
Media Redundancy Protocol (MRP) is a data network protocol standardized by the International Electrotechnical Commission as IEC 62439-2. It allows rings of Ethernet switches to overcome any single failure with recovery time much faster than achievable with Spanning Tree Protocol. It is suitable to most industrial Ethernet applications. Properties MRP operates at the data link layer (OSI Layer 2) of Ethernet switches and is a direct evolution of the HiPER-Ring protocol developed by Hirschmann in 1998. Hirschmann is now owned by Belden. MRP is supported by several commercial industrial Ethernet switches. In an MRP ring, the ring manager is named Media Redundancy Manager (MRM), while ring clients are named Media Redundancy Clients (MRCs). MRM and MRC ring ports support three statuses: disabled, blocked, and forwarding. Disabled ring ports drop all the received frames. Blocked ring ports drop all the received frames except the MRP control frames. Forwarding ring ports forward a ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
International Electrotechnical Commission
The International Electrotechnical Commission (IEC; in French: ''Commission électrotechnique internationale'') is an international standards organization that prepares and publishes international standards for all electrical, electronic and related technologies – collectively known as "electrotechnology". IEC standards cover a vast range of technologies from power generation, transmission and distribution to home appliances and office equipment, semiconductors, fibre optics, batteries, solar energy, nanotechnology and marine energy as well as many others. The IEC also manages four global conformity assessment systems that certify whether equipment, system or components conform to its international standards. All electrotechnologies are covered by IEC Standards, including energy production and distribution, electronics, magnetics and electromagnetics, electroacoustics, multimedia, telecommunication and medical technology, as well as associated general disciplines such as t ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Ethernet
Ethernet () is a family of wired computer networking technologies commonly used in local area networks (LAN), metropolitan area networks (MAN) and wide area networks (WAN). It was commercially introduced in 1980 and first standardized in 1983 as IEEE 802.3. Ethernet has since been refined to support higher bit rates, a greater number of nodes, and longer link distances, but retains much backward compatibility. Over time, Ethernet has largely replaced competing wired LAN technologies such as Token Ring, FDDI and ARCNET. The original 10BASE5 Ethernet uses coaxial cable as a shared medium, while the newer Ethernet variants use twisted pair and fiber optic links in conjunction with switches. Over the course of its history, Ethernet data transfer rates have been increased from the original to the latest , with rates up to under development. The Ethernet standards include several wiring and signaling variants of the OSI physical layer. Systems communicating over Ethernet ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Spanning Tree Protocol
The Spanning Tree Protocol (STP) is a network protocol that builds a loop-free logical topology for Ethernet networks. The basic function of STP is to prevent bridge loops and the broadcast radiation that results from them. Spanning tree also allows a network design to include backup links providing fault tolerance if an active link fails. As the name suggests, STP creates a spanning tree that characterizes the relationship of nodes within a network of connected layer-2 bridges, and disables those links that are not part of the spanning tree, leaving a single active path between any two network nodes. STP is based on an algorithm that was invented by Radia Perlman while she was working for Digital Equipment Corporation. In 2001, the IEEE introduced Rapid Spanning Tree Protocol (RSTP) as 802.1w. RSTP provides significantly faster recovery in response to network changes or failures, introducing new convergence behaviors and bridge port roles to do this. RSTP was designed to be b ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Industrial Ethernet
Industrial Ethernet (IE) is the use of Ethernet in an industrial environment with protocols that provide determinism and real-time control. Protocols for industrial Ethernet include EtherCAT, EtherNet/IP, PROFINET, POWERLINK, SERCOS III, CC-Link IE, and Modbus TCP. Many industrial Ethernet protocols use a modified Media Access Control (MAC) layer to provide low latency and determinism. Some microcontrollers such as Sitara provide industrial Ethernet support. Industrial Ethernet can also refer to the use of standard Ethernet protocols with rugged connectors and extended temperature switches in an industrial environment, for automation or process control. Components used in plant process areas must be designed to work in harsh environments of temperature extremes, humidity, and vibration that exceed the ranges for information technology equipment intended for installation in controlled environments. The use of fiber-optic Ethernet variants reduces the problems of electrical ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Belden (electronics Company)
Belden Incorporated is an American manufacturer of networking, connectivity, and cable products. The company designs, manufactures, and markets signal transmission products for demanding applications. These products serve the industrial automation, enterprise, security, transportation, infrastructure, and residential markets. Belden is one of the largest U.S.-based manufacturers of high-speed electronic cables primarily used in industrial, enterprise, and broadcast markets. Structure Belden is headquartered in St. Louis, Missouri. Its president and CEO is Roel Vestjens. Belden operates in three regions: * The Americas * Europe, Middle East and Africa (EMEA) * Asia Pacific PPC Belden PPC, a division of Belden, holds a number of patents for connector technology and has pioneered advancements for various industries. PPC Belden's innovations include the Universal Compression Connector, the wireless compression connector for the wireless industry and a locking HDMI connector. It ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Ethernet Frame
In computer networking, an Ethernet frame is a data link layer protocol data unit and uses the underlying Ethernet physical layer transport mechanisms. In other words, a data unit on an Ethernet link transports an Ethernet frame as its payload. An Ethernet frame is preceded by a preamble and start frame delimiter (SFD), which are both part of the Ethernet packet at the physical layer. Each Ethernet frame starts with an Ethernet header, which contains destination and source MAC addresses as its first two fields. The middle section of the frame is payload data including any headers for other protocols (for example, Internet Protocol) carried in the frame. The frame ends with a frame check sequence (FCS), which is a 32-bit cyclic redundancy check used to detect any in-transit corruption of data. Structure A data packet on the wire and the frame as its payload consist of binary data. Ethernet transmits data with the most-significant octet (byte) first; within each octet, howe ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
EtherType
EtherType is a two-octet field in an Ethernet frame. It is used to indicate which protocol is encapsulated in the payload of the frame and is used at the receiving end by the data link layer to determine how the payload is processed. The same field is also used to indicate the size of some Ethernet frames. EtherType is also used as the basis of 802.1Q VLAN tagging, encapsulating packets from VLANs for transmission multiplexed with other VLAN traffic over an Ethernet trunk. EtherType was first defined by the Ethernet II framing standard and later adapted for the IEEE 802.3 standard. EtherType values are assigned by the IEEE Registration Authority. Overview In modern implementations of Ethernet, the field within the Ethernet frame used to describe the EtherType can also be used to represent the size of the payload of the Ethernet Frame. Historically, depending on the type of Ethernet framing that was in use on an Ethernet segment, both interpretations were simultaneous ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Type–length–value
Within communication protocols, TLV (type-length-value or tag-length-value) is an encoding scheme used for optional informational elements in a certain protocol. A TLV-encoded data stream contains code related to the record type, the record value's length, and finally the value itself. Details The type and length are fixed in size (typically 1–4 bytes), and the value field is of variable size. These fields are used as follows: ;Type: A binary code, often simply alphanumeric, which indicates the kind of field that this part of the message represents; ;Length: The size of the value field (typically in bytes); ;Value: Variable-sized series of bytes which contains data for this part of the message. Some advantages of using a TLV representation data system solution are: * TLV sequences are easily searched using generalized parsing functions; * New message elements which are received at an older node can be safely skipped and the rest of the message can be parsed. This is similar ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Parallel Redundancy Protocol
Parallel Redundancy Protocol (PRP) is a network protocol standard for Ethernet that provides seamless failover against failure of any network component. This redundancy is invisible to the application. PRP nodes have two ports and are attached to two separated networks of similar topology. PRP can be implemented entirely in software, i.e. integrated in the network driver. Nodes with single attachment can be attached to one network only. This is in contrast to the companion standard HSR (IEC 62439-3 Clause 5), with which PRP shares the operating principle. PRP and HSR are independent of the application-protocol and can be used by most Industrial Ethernet protocols in the IEC 61784 suite. PRP and HSR are standardized by the IEC 62439-3:2016). They have been adopted for substation automation in the framework of IEC 61850. PRP and HSR are suited for applications that request high availability and short switchover time, such as: protection for electrical substation, synchronize ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
High-availability Seamless Redundancy
High-availability Seamless Redundancy (HSR) is a network protocol for Ethernet that provides seamless failover against failure of any single network component. PRP and HSR are independent of the application-protocol and can be used by most Industrial Ethernet protocols in the IEC 61784 suite. HSR does not cover the failure of end nodes, but redundant nodes can be connected via HSR. HSR nodes have two ports and act as a bridge, which allows arranging them into a ring or meshed structure without dedicated switches. This is in contrast to the companion standard Parallel Redundancy Protocol (PRP), with which HSR shares the operating principle. PRP and HSR are standardized by the IEC 62439-3:2016. PRP and HSR are suited for applications that request high availability and short switchover time. For such applications, the recovery time of commonly used protocols such as the Rapid Spanning Tree Protocol (RSTP) is too long. It has been adopted for electrical substation automation in the ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Fieldbus
Fieldbus is the name of a family of industrial computer networks used for real-time distributed control. Fieldbus profiles are standardized by the International Electrotechnical Commission (IEC) as IEC 61784/61158. A complex automated industrial system is typically structured in hierarchical levels as a distributed control system (DCS). In this hierarchy the upper levels for production managements are linked to the direct control level of programmable logic controllers (PLC) via a non-time-critical communications system (e.g. Ethernet). The fieldbus links the PLCs of the direct control level to the components in the plant of the field level such as sensors, actuators, electric motors, console lights, switches, valves and contactors and replaces the direct connections via current loops or digital I/O signals. The requirement for a fieldbus are therefore time-critical and cost sensitive. Since the new millennium a number of fieldbuses based on Real-time Ethernet have been establish ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
