|
HY-80
HY-80 is a high-tensile, high yield strength, low alloy steel. It was developed for use in naval applications, specifically the development of pressure hulls for the US nuclear submarine program and is still currently used in many naval applications. It is valued for its strength to weight ratio. The "HY" steels are designed to possess a high yield strength (strength in resisting permanent plastic deformation). HY-80 is accompanied by HY-100 and HY-130 with each of the 80, 100 and 130 referring to their yield strength in ksi (80,000 psi, 100,000 psi and 130,000 psi). HY-80 and HY-100 are both weldable grades; whereas, the HY-130 is generally considered unweldable. Modern steel manufacturing methods that can precisely control time/temperature during processing of HY steels has made the cost to manufacture more economical. HY-80 is considered to have good corrosion resistance and has good formability to supplement being weldable. Using HY-80 steel requires careful consideration ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Skipjack-class Submarine
The ''Skipjack'' class was a class of United States Navy nuclear submarines (SSNs) that entered service in 1959-61. This class was named after its lead boat, . The new class introduced the teardrop hull and the S5W reactor to U.S. nuclear submarines. The ''Skipjack''s were the fastest U.S. nuclear submarines until the s, the first of which entered service in 1974. Design The ''Skipjack''s' design (project SCB 154)Friedman, pp. 258 was based on the USS ''Albacore'''s high-speed hull design. The hull and innovative internal arrangement were similar to the diesel-powered ''Barbel'' class that were built concurrently. The design of the ''Skipjack''s was very different from the s that preceded the ''Skipjack''s. Unlike the ''Skate''s, this new design was maximized for underwater speed by fully streamlining the hull like a blimp. This required a single screw aft of the rudders and stern planes. Adoption of a single screw was a matter of considerable debate and analysis within th ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Crush Depth
Depth ratings are primary design parameters and measures of a submarine's ability to operate underwater. The depths to which submarines can dive are limited by the strengths of their submarine hull, hulls. Ratings The hull of a submarine must be able to withstand the forces created by the outside water pressure being greater than the inside air pressure. The outside water pressure increases with depth and so the stresses on the hull also increase with depth. Each 10 metres (33 feet) of depth puts another atmosphere (1 bar, 14.7 psi, 101 kPa) of pressure on the hull, so at 300 metres (1,000 feet), the hull is withstanding thirty atmospheres (30 bar, 441 psi, 3,000 kPa) of water pressure. Test depth The maximum depth at which a submarine is permitted to operate under normal peacetime circumstances, and is tested during sea trials. The test depth is set at two-thirds (0.66) of the design depth for United States Navy submarines, while the Royal Navy sets test depth at 4/7 (0.57) t ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Seawolf-class Submarine
The ''Seawolf'' class is a class of nuclear-powered, fast attack submarines (SSN) in service with the United States Navy. The class was the intended successor to the , and design work began in 1983. A fleet of 29 submarines was to be built over a ten-year period, but that was reduced to 12 submarines. The end of the Cold War and budget constraints led to the cancellation of any further additions to the fleet in 1995, leaving the ''Seawolf'' class limited to just three boats. This, in turn, led to the design of the smaller . The ''Seawolf'' class cost about $3 billion per unit ($3.5 billion for ), making it the most expensive United States Navy fast attack submarine and second most expensive submarine ever, after the French nuclear-powered ballistic missile submarines. Design The ''Seawolf'' design was intended to combat the threat of advanced Soviet ballistic missile submarines such as the , and attack submarines such as the in a deep-ocean environment. ''Seawolf''-class hull ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Permit-class Submarine
The ''Permit''-class submarine (known as the ''Thresher'' class until the lead boat was lost) was a class of nuclear-powered fast attack submarines (hull classification symbol SSN) in service with the United States Navy from the early 1960s until 1996. They were a significant improvement on the , with greatly improved sonar, diving depth, and silencing. They were the forerunners of all subsequent US Navy SSN designs. They served from the 1960s through to the early 1990s, when they were decommissioned due to age. They were followed by the and classes. The ''Thresher'' class was one of several results from a study commissioned in 1956 by Chief of Naval Operations (CNO) Admiral Arleigh Burke. In "Project Nobska", the Committee on Undersea Warfare of the United States National Academy of Sciences, collaborating with numerous other agencies, considered the lessons of submarine warfare and anti-submarine warfare learned from various prototypes and experimental platforms. The design w ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Special Treatment Steel
Special treatment steel (STS), also known as protective deck plate, was a type of warship armor developed by Carnegie Steel around 1910. History STS is a homogeneous Krupp-type steel developed around 1910. The development of such homogeneous steel resulted in testing which showed that face-hardened armor was less effective against high-obliquity glancing impacts. Around 1910, Carnegie Steel developed a new nickel-chrome-vanadium alloy-steel that offers improved protection over the prior nickel steel armor, though vanadium was no longer used after 1914. This alloy-steel became known as "Special Treatment Steel (STS)"; it became the U.S. Navy Bureau of Construction and Repair (later Bureau of Ships) standard form of high-percentage nickel steel used on all portions of a warship needing homogeneous direct impact protection armor. STS was used as homogeneous armor that was less than thick; homogeneous armor for gun mounts and conning towers, where the thicknesses were considerably ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Bureau Of Ships
The United States Navy's Bureau of Ships (BuShips) was established by Congress on 20 June 1940, by a law which consolidated the functions of the Bureau of Construction and Repair (BuC&R) and the Bureau of Engineering (BuEng). The new bureau was to be headed by a chief and deputy-chief, one selected from the Engineering Corps (Marine Engineer) and the other from the Construction Corps (Naval Architect). The chief of the former Bureau of Engineering, Rear Admiral Samuel M. "Mike" Robinson, was named BuShips' first chief, while the former chief of the Bureau of Construction & Repair, Rear Admiral Alexander H. Van Keuren, was named as BuShips' first Deputy-Chief. The bureau's responsibilities included supervising the design, construction, conversion, procurement, maintenance, and repair of ships and other craft for the Navy; managing shipyards, repair facilities, laboratories, and shore stations; developing specifications for fuels and lubricants; and conducting salvage operations. Bu ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Face-centred Cubic
In crystallography, the cubic (or isometric) crystal system is a crystal system where the unit cell is in the shape of a cube. This is one of the most common and simplest shapes found in crystals and minerals. There are three main varieties of these crystals: *Primitive cubic (abbreviated ''cP'' and alternatively called simple cubic) *Body-centered cubic (abbreviated ''cI'' or bcc) *Face-centered cubic (abbreviated ''cF'' or fcc, and alternatively called ''cubic close-packed'' or ccp) Each is subdivided into other variants listed below. Although the ''unit cells'' in these crystals are conventionally taken to be cubes, the primitive unit cells often are not. Bravais lattices The three Bravais lattices in the cubic crystal system are: The primitive cubic lattice (cP) consists of one lattice point on each corner of the cube; this means each simple cubic unit cell has in total one lattice point. Each atom at a lattice point is then shared equally between eight adjacent cubes, ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Metallurgical And Materials Transactions
''Metallurgical and Materials Transactions'' is a peer-reviewed scientific journal published in three sections (''A, B,'' and ''E'') covering metallurgy and materials science. The journals are jointly published by The Minerals, Metals & Materials Society and ASM International. ''Metallurgical and Materials Transactions A'' This monthly section focuses on physical metallurgy {{unreferenced, date=April 2017 Physical metallurgy is one of the two main branches of the scientific approach to metallurgy, which considers in a systematic way the physical properties of metals and alloys. It is basically the fundamentals and app ... and materials science, and publishes international scientific contributions on all aspects of physical metallurgy and materials science, with a special emphasis on relationships among the processing, structure, and properties of materials. ''Metallurgical and Materials Transactions B'' This bimonthly section is uniquely focused on process metallurgy and ma ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Bainite
Bainite is a plate-like microstructure that forms in steels at temperatures of 125–550 °C (depending on alloy content). First described by E. S. Davenport and Edgar Bain, it is one of the products that may form when austenite (the face-centered cubic crystal structure of iron) is cooled past a temperature where it is no longer thermodynamically stable with respect to ferrite, cementite, or ferrite and cementite. Davenport and Bain originally described the microstructure as being similar in appearance to tempered martensite. A fine non-lamellar structure, bainite commonly consists of cementite and dislocation-rich ferrite. The large density of dislocations in the ferrite present in bainite, and the fine size of the bainite platelets, makes this ferrite harder than it normally would be. The temperature range for transformation of austenite to bainite (125–550 °C) is between those for pearlite and martensite. In fact, there is no fundamental lower limit to the ba ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Martensite
Martensite is a very hard form of steel crystalline structure. It is named after German metallurgist Adolf Martens. By analogy the term can also refer to any crystal structure that is formed by diffusionless transformation. Properties Martensite is formed in carbon steels by the rapid cooling (quenching) of the austenite form of iron at such a high rate that carbon atoms do not have time to diffuse out of the crystal structure in large enough quantities to form cementite (Fe3C). Austenite is gamma-phase iron (γ-Fe), a solid solution of iron and alloying elements. As a result of the quenching, the face-centered cubic austenite transforms to a highly strained body-centered tetragonal form called martensite that is supersaturated with carbon. The shear deformations that result produce a large number of dislocations, which is a primary strengthening mechanism of steels. The highest hardness of a pearlitic steel is 400 Brinell, whereas martensite can achieve 700 Bri ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Austenite
Austenite, also known as gamma-phase iron (γ-Fe), is a metallic, non-magnetic allotrope of iron or a solid solution of iron with an alloying element. In plain-carbon steel, austenite exists above the critical eutectoid temperature of 1000 K (727 °C); other alloys of steel have different eutectoid temperatures. The austenite allotrope is named after Sir William Chandler Roberts-Austen (1843–1902); it exists at room temperature in some stainless steels due to the presence of nickel stabilizing the austenite at lower temperatures. Allotrope of iron From alpha iron undergoes a phase transition from body-centered cubic (BCC) to the face-centered cubic (FCC) configuration of gamma iron, also called austenite. This is similarly soft and ductile but can dissolve considerably more carbon (as much as 2.03% by mass at ). This gamma form of iron is present in the most commonly used type of stainless steel for making hospital and food-service equipment. Material Austenitizati ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Chromium
Chromium is a chemical element with the symbol Cr and atomic number 24. It is the first element in group 6. It is a steely-grey, lustrous, hard, and brittle transition metal. Chromium metal is valued for its high corrosion resistance and hardness. A major development in steel production was the discovery that steel could be made highly resistant to corrosion and discoloration by adding metallic chromium to form stainless steel. Stainless steel and chrome plating (electroplating with chromium) together comprise 85% of the commercial use. Chromium is also greatly valued as a metal that is able to be highly polished while resisting tarnishing. Polished chromium reflects almost 70% of the visible spectrum, and almost 90% of infrared light. The name of the element is derived from the Greek word χρῶμα, ''chrōma'', meaning color, because many chromium compounds are intensely colored. Industrial production of chromium proceeds from chromite ore (mostly FeCr2O4) to produce ferro ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
_on_the_ways_at_Mare_Island.jpg "Click for more on -> HY-80")
