Schweizer SGU 2-22

The Schweizer SGU 2-22 is an American two-seat, high-wing, strut-braced, training glider built by Schweizer Aircraft of Elmira, New York.Said, Bob: ''1983 Sailplane Directory, Soaring Magazine'', pages 26. Soaring Society of America, November 1983. USPS 499-920

The 2-22 was designed to replace the two-place training gliders surplussed at the end of World War II . Production was started in 1946 and it was produced until 1967, when it was superseded by an improved version, the SGS 2-33. From the 1940s until the 1960s it was the most numerous two-place training glider in the USA.

Design and development

The end of World War Two resulted in a large number of military training gliders being sold as surplus. These included Frankfort TG-1s, Schweizer TG-2s and Schweizer TG-3s. Most of the surplus gliders sold were not ideal trainers for ab initio civilian student flying, as they had high wing loadings and faster stall speeds. This made them suitable for aerotow, but not for winch or auto-tow launches. Furthermore, many of these surplus two-place gliders had poor visibility from the rear seat where the instructor sat. Due to restrictions on the use of aluminum in training aircraft, many surplus gliders had wooden wings, making them unsuitable to be kept outdoors on tie-downs.

Schweizer Aircraft decided to design a two-place trainer that would address these deficiencies and provide a trainer that was easy to fly and would be easy for students to progress quickly on. The new two-place was intended to be a complement to the single-place training glider then in production, the SGU 1-19.

The SGU 2-22, indicating ''Schweizer Glider, Utility, 2 Seats, Model 22'', was designed by Ernest Schweizer. The aircraft was based on the SGU 1-7 single place glider of 1937. It used the 1-7's metal wing, single spar and single strut arrangement. The prototype 2-22 was flown in March, 1946. To gain publicity for the new design company test pilot Frank Hurtt and company engineer Dick Powell used the prototype to set a new two-place duration record of 10 hours 9 minutes on April 10, 1946. The 2-22 was produced in seven variants and remained in production for 21 years. Production was only curtailed when the Schweizer SGS 2-33 was put into production as a replacement. The 2-33 was essentially a refined 2-22, incorporating a longer semi-tapered wing.

The 2-22 has a welded steel tube fuselage covered in aircraft fabric. The single-spar, constant-chord aluminum structure wings feature spoilers on the top surface only and are covered in aircraft fabric. The tail surfaces are made from welded steel tube covered in aircraft fabric.

The 2-22 received type certificate G-18 on 4 October 1946. The type certificate is currently held by K & L Soaring of Cayuta, New York who now provide all parts and support for the Schweizer line of sailplanes.

A number of 2-22s were delivered as kits to the purchaser. These were accepted by the Federal Aviation Administration as certified aircraft and not amateur-builts, subject to conditions:

Variants

;SGU 2-22

:The original 2-22 is referred to as a "standard". It featured a 450 lb (204 kg) empty weight and an 830 lb (376 kg) gross weight. The aircraft had a windshield, but no canopy, rear windows or door. Fifty-one "standards" were built. The type was certified on 4 October 1946.

;SGU 2-22A

:The "A" model was a re-design to meet the requirements of the United States Air Force Academy. It incorporated a lengthened nose and a full canopy, along with a gross weight increase to 900 lbs (408 kg). It was certified on 24 May 1957. A total of three were completed.

;SGU 2-22B

:The "B" model was a "standard" with the gross weight increased to 900 lbs (408 kg). It was certified on 24 May 1957.

;SGU 2-22C

:The "C" model incorporated the changes from the "A" and "B" models and also introduced smaller ailerons. It was certified on 24 May 1957 and 103 were built.

;SGU 2-22CK

:The "CK" model was a "C" model completed by the buyer from a kit. Twenty-eight "CK" kits were completed.

;SGU 2-22E

:The "E" model was the last production model and incorporated larger spoilers, a bigger cockpit, a new-design canopy and changes to the wing root to allow a skylight to be fitted. The "E" was certified on 10 April 1963.

;SGU 2-22EK

:The "EK" was the kit version of the "E" model. The "EK" was certified on 7 February 1964.

Operational history

Aside from the 2-22As that were delivered to USAFA, later model 2-22s were also supplied to the USAF and a number were supplied as foreign aid to Indonesia.

Distance flying in the 2-22 is challenging, given its 17:1 glide ratio. One 2-22 was flown by Al Parker 200 miles (324 km) to complete a Gold distance and Diamond goal leg.

In May 2008 there were still 123 SGU 2-22s registered in the USA. These included:

*2-22 - 19
*2-22A - 1
*2-22B - 0
*2-22C - 28
*2-22CK - 14
*2-22E - 55
*2-22EK - 6

Aircraft on display

*US Southwest Soaring Museum

Specifications (SGU 2-22)

See also

References

{{DEFAULTSORT:Schweizer Sgu 2-22
1940s United States sailplanes
Schweizer aircraft
Glider aircraft
High-wing aircraft
Aircraft first flown in 1946