Principal Triangulation of Great Britain

The Principal Triangulation of Britain was the first high-precision triangulation survey of the whole of Great Britain and Ireland, carried out between 1791 and 1853 under the auspices of the Board of Ordnance. The aim of the survey was to establish precise geographical coordinates of almost 300 significant landmarks which could be used as the fixed points of local topographic surveys from which maps could be drawn. In addition there was a purely scientific aim in providing precise data for geodetic calculations such as the determination of the length of meridian arcs and the figure of the Earth. Such a survey had been proposed by William Roy (1726–1790) on his completion of the Anglo-French Survey but it was only after his death that the Board of Ordnance initiated the trigonometric survey, motivated by military considerations in a time of a threatened French invasion. Most of the work was carried out under the direction of Isaac Dalby, William Mudge and Thomas Frederick Colby, but the final synthesis and report (1858) was the work of Alexander Ross Clarke. The survey stood the test of time for a century, until the Retriangulation of Great Britain between 1935 and 1962.

History

In the aftermath of the Jacobite rising of 1745, the Duke of Cumberland (military commander against the rebels) advised by Lieutenant-Colonel David Watson, a Deputy Quartermaster-General of the Board of Ordnance recognised that there was a need for an accurate map of the Scottish Highlands. Watson initiated the necessary survey in 1747. Watson employed William Roy as a civilian assistant to carry out the bulk of the work. Subsequently Roy, having taken a commission in the Corps of Engineers as a "practitioner engineer", and having become a very competent surveyor, proposed (in a memorandum to the king dated 24 May 1766) a national survey which would be a plan for defence at a time when French invasions were threatened. The proposal was rejected on grounds of expense.

Roy continued to lobby for a survey and his ambitions were realised to a certain extent by an unexpected development. In 1783 the French Academy of Sciences claimed that the latitude and longitude differences between the Royal Observatory, Greenwich and the Paris Observatory were incorrect, and it was proposed (to the Royal Society) that the differences could be reconciled by high precision triangulation over the intervening terrain. The Royal Society agreed and, jointly with the Board of Ordnance, they invited Roy to oversee the project.

Roy's first task (1784) was to measure a baseline between Hampton Poor House () and King's Arbour () on Hounslow Heath, a distance of just over 5 miles (8 km). This was a painstaking process: three rods each of 20 ft. were supported on trestles and the ends aligned to an accuracy of a thousandth part of an inch. The first rod was then carried to the end of the third, an operation to be repeated 1,370 times. The first set of rods, from instrument maker Jesse Ramsden, was made of wood and, in the particularly wet weather of the Summer of 1784, these were found subject to warping and expansion. After delay of two weeks, Ramsden delivered a new set of rods, now made of solid glass tubing. Mounted in rigid wooden boxes with open ends, these had a sprung brass pin mounted against an ivory scale at one end, and this showed when the rods were joined exactly. The final measurement gave the length of the base as .

For the subsequent triangulation, Roy ordered a new theodolite from Jesse Ramsden. This Ramsden theodolite, delivered in 1787, for the first time divided angular scales accurately to within a second of arc. The theodolite was the largest ever constructed but, despite its massive size, it was carried from London to the Channel coast and employed on hills, steeples and a moveable tower. At each location the angles to other vertices of the triangulation mesh were measured many times, often at night time using newly devised lights. Finally the angle data was used to calculate the sides of the triangles by using spherical trigonometry.

The final results were inconclusive, for triangulation was inferior to the precision of astronomical measurements, but the survey paved the way for all future work in terms of high precision measurements of length and angle, together with the techniques of calculating on an ellipsoidal surface. In his final report, published posthumously, Roy once again pressed for the extension of the survey to the rest of Britain. Charles Lennox, 3rd Duke of Richmond, as Master of the Board of Ordnance from 1782, viewed Roy's work with great interest. At the same time he was acutely aware that Britain, lacking a national survey, was falling behind the standards of many other European countries. Moreover, the renewed threat of French invasion made him alarmed at the lack of accurate maps, particularly of the southern counties. Consequently, in 1791, he put into action Roy's plan for the extension of the survey. The catalyst was the sudden availability of a new improved Ramsden theodolite which had been intended for the East India Company. The purchase of this instrument on 21 June 1791 by the Board is taken as the inauguration of the Ordnance Survey. The very next day Richmond appointed Isaac Dalby as its first employee, with a brief to extend Roy's survey. In the following month Richmond appointed two officers of the Royal Artillery, Major Edward Williams and Lieutenant William Mudge, as directors.

Re-measurement of the Hounslow baseline

For the 1784 measurement of the original baseline across Hounslow Heath, Roy had ordered three deal rods cut from a new mast in the Admiralty dock yards. These were intended to be used for the precision measurement but Roy also ordered a 100 ft steel chain from Ramsden which could be used for a quick preliminary measurement. The deal rods proved ineffective because of their changes with humidity and they were replaced with glass rods for the final measurement; however Roy observed that the chain itself was just as accurate as the rods. For this reason when Richmond ordered Mudge to remeasure the Hounslow base in Summer of 1791, as a first step in extending the triangulation, the survey started by remeasuring the base with two new chains, again made by Ramsden. The second chain was kept unused as a reference against which any stretching of the first would be detected.

The process of measurement was exceedingly precise. Since the ground was undulating along the length of the base, the measurement was carried out over 26 stages with varying slopes, the chains for any one stage being constrained to a perfectly straight line by many intermediate supports. These hypotenuse measurements were then projected to the horizontal. Furthermore, the temperature varied from day to day and each measurement was corrected to the length that a chain would take at . Finally, the length of the base was reduced to its projection at sea level using the height of the south base above the Thames and the fall in the Thames down to its estuary. The final result was approximately less than that of Roy; the mean value of was taken for the baseline. The modern value, derived from GPS, is , a difference of .

Corrections

As the survey proceeded westwards, Mudge decided to check its accuracy by measuring a new baseline between two points established by the triangulation. He chose Salisbury Plain, measuring between a point near Old Sarum Castle () and Beacon Hill, near Bulford (), in June 1794. The difference between the distance calculated by triangulation and that established by measurement was less than one inch (over a length of more than seven miles). The result verified not only the accuracy of the triangulation, but also the measurement of the original baseline on Hounslow Heath. After remeasurement in 1849 the "Salisbury Base" (rather than the original base on Hounslow Heath) provided the baseline for subsequent triangulation.

During subsequent triangulation, errors due to atmospheric refraction, deflection of plumb-bobs, temperature, and the spherical nature of the earth (meaning there were more than 180 degrees in a triangle) were all allowed for.

New national triangulation

In 1909 it was decided that, because of improvements in the design of theodolites, a test of angles recorded in the previous triangulation was necessary. The baseline at Lossiemouth, Morayshire, was selected. The length of the base (measured using the new invar steel tapes) was found to correspond satisfactorily with the previous value obtained through triangulation, and that any new survey would not vary significantly from the one completed in the previous century. In 1935, however, General Malcolm MacLeod, OS director, decided that a new national triangulation, the Retriangulation of Great Britain, was required. This was not because of any deficiency in the existing principal triangulation, but because some secondary, local triangulations were not of a standard where they could be reconciled within the existing national framework.

See also

* Ordnance Survey
* Ordnance Survey Drawings
* Great Trigonometrical Survey (Indian subcontinent)
* Public Land Survey System (United States)

Notes

References

Bibliography

*
*
*
*
*
*
*
*
*
*
*
*
*
*

Further reading

*
*
*

*
**
*

External links

PDF file including history and map of the Irish part and its links to Britain

Information and Maps
on many aspects of Triangulation (& Levelling) in Great Britain
*
*

{{DEFAULTSORT:Principal Triangulation Of Great Britain
Cartography
Geography of the United Kingdom
Historical geography of the United Kingdom
1784 in Great Britain
Maps of the United Kingdom
Geodetic surveys
Surveying of the United Kingdom