manual handling of loads

Manual handling of loads (MHL), manual material handling (MMH) involves the use of the human body to lift, lower, carry or transfer loads.  The average person is exposed to manual lifting of loads in the work place, in recreational atmospheres, and even in the home. To properly protect one from injuring themselves, it can help to understand general body mechanics.

Manual Handling of Materials- Hazards and Injuries

Manual handling of materials can be found in any workplace from offices to heavy industrial and manufacturing facilities. Often times, manual material handling entails tasks such as lifting, climbing, pushing, pulling, and pivoting, all of which pose the risk of injury to the back and other skeletal systems which can often lead to Musculoskeletal Disorders. Musculoskeletal disorders can be defined as “Musculoskeletal disorders often involve strains and sprains to the lower back, shoulders, and upper limbs.” According to a Department of Labor study published in 1990, back injuries accounted for approximately 20% of all injuries in the workplace which accounted for almost 25% of the total workers compensation payouts.

To better understand the potential injuries of manual handling of materials, we must first understand the underlying conditions which can cause the injuries. When an injury occurs from manual handling of materials, it often is a result of one of the following underlying condition(s).

·      Awkward Posture (Bending or twisting)

·      Repetitive Motions (Frequency of a task)

·      Forceful exertions (Carrying or lifting heavy loads)

·      Pressure points (The load applying pressure to select areas on the body only)

·      Static postures (Staying in the same position for extended periods of time

Although MSD’s can develop overtime, when manual handling of materials, an MSD can occur after only one activity. Some of the common injuries associated with manual handling of loads include but are not limited to:

·      Sprains and strains of muscles, ligaments, and tendons

·      Back injuries

·      Bone injuries

·      Nerve Injuries

·       Tissue Injuries

·      Acute and Chronic Pain

In addition to the injuries listed above, the worker can be exposed to soreness, bruises, cuts, punctures, crushing, and even amputations.

Remember your health comes first, it is temporary so make good use of it.

Industries and Workforces Commonly Affected

Although employee’s can be exposed to manual handling of materials in any industry or workplace there are workplaces that are more susceptible to hazards of manual material handling. These industries include but are not limited to:

·      Warehousing

·      Manufacturing Facilities

·      Factories

·      Construction Sites

·      Hospitals

·      Nursing Home and Retirement Facilities

·      Emergency Services (Fire, EMS, Police)

·      Farms/Ranches

Tools to Evaluate or Assess Manual Handling Tasks

There are multiple tools which can be used to assess the manual handling of material. Some of the most common methods are discussed below in no particular order.

1.     NIOSH Lifting Equation

The National Institute for Occupational Safety and Health often referred to as NIOSH is a division of the Center for Disease Control and Prevention (CDC) under the United States Department of Health and Human Services. NIOSH first published the NIOSH lifting equation in 1991 and went into effect July 1994. NIOSH made changes to the NIOSH lifting equation manual in 2021 which included updated graphics and tables and identified errors were corrected.

The NIOSH lifting equation is a tool (no
application
) that can be used by health and safety professionals to assess employees who are exposed to manual lifting or handling of materials.  The NIOSH lifting equation is a mathematical calculation which calculates the Recommended Weight Limit (RWL) using a series of tables, variables, and constants. The equation for the NIOSH lifting equation is shown below

$RWL= LC\times HM\times VM\times DM\times AM\times FM\times CM$

where:

LC= Load Constant (23 kg or 51 lb)

HM= Horizontal Multiplier

VM=Vertical Multiplier

DM= Distance Multiplier

AM= Asymmetric Multiplier

FM= Frequency Multiplier

CM=Coupling Multiplier

Using the RWL, you can also find the Lifting Index (LI) using the following equation:

$LI=(LoadWeight)/RWL$

The Lifting Index can be used to identify the stresses that each lift will expose the employees. The general understanding is that as the LI increased, the higher risk the worker is exposed to. As the LI decreases, the worker is less likely to develop back related injuries. Ideally, any lifting tasks should have a lifting index of 1.0 or less.

The NIOSH lifting Equation does have some limitations which include:

·      Only using one hand for lifting/lowering

·      Lifting or Lowering for over 8 hours

·      Lifting or lowering while in the seated or kneeling position

·      Lifting or lowering in restricted areas (where full range of motion cannot be achieved.

·      Lifting or lowering unstable objects

·      Lifting or lowering while carrying, pushing, or pulling.

·      Lifting or lowering using devices such as wheelbarrows or shovels

·      Lifting or lowering with high speed motion

·      Lifting or lowering on unstable floors

·      Lifting or lowering in extreme heat, cold, or humidity.

The NIOSH Revised Lifting Equation Manual can be found on the CDC’s website or by clickin
here.

2.     Liberty Mutual Tables

Liberty Mutual Insurance has studied the practice of all tasks related to manual materials handling. The result of their studies is a comprehensive set of tables which predicts the percentages of both the Male and Female population that can move the weight of the object. The Liberty Mutual Risk Control Team recommends that tasks should be designed so that 75% or more of the female work force population can safely complete the task.

Key components that first must be collected before using the Liberty Mutual Tables are:

·      Total Weight of object

·      Hand Distance (Distance Away from the Body)

·      Initial Hand Height (Hand Height at Start of Lift)

·      Final Hand Height (Hand Height at end of Lift)

·      Frequency (How often is this task completed)

The complete Liberty Mutual Tables and their guidelines can be foun
here
Liberty Mutual Insurance also has provided calculators that will manually calculate the percentage for both the male and female populations. If the percentage is less than 75% for the female population, a redesign of the lifting plan should be created so that 75% or more of the female population can conduct the materials handling. The link to the calculator can be foun
here

3.     REBA

REBA is an acronym for Rapid Entire Body Assessment. This tool was developed by Dr. Sue Hignett and Dr. Lynn McAtamney which was published July 1998 in the Applied Ergonomics Journal. This measurement device was designed to be a tool that health and safety professionals could use in the field to assess posture techniques in the workplace. Rather than heavily reliant on the weight of the object being lifted, Dr. Hignett and Dr. McAtamney developed this tool based on the posture of the employee lifting the weight. Using a series of mathematical calculations and a series of tables, each activity is assigned a REBA score. To calculate the REBA score, the tool separates the body parts into two groups: Group A and Group B. The body parts assigned to Group A are:

·      Neck

·      Trunk

·      Legs

The body parts assigned to group B are:

·      Upper Arms

·      Lower Arms

·      Wrists

Using the score of each body part posture in group A, locate the score in Table A to assign a Group A Posture Score. This score is then added to the Load or force. This sum is the Score A.

Using the score of each body part posture in group B, locate the score in Table b to assign a Group B Posture Score. This score is then added to the coupling score. This sum is the Score B.

Using Score A and Score B, assign the correct Score C using Table C. The Score C is then added to the Activity Score. This sum is the REBA score. The REBA Score is a numerical value between 0 and 4. A REBA score 0 has a negligible risk level and a REBA score 4 has a very high-risk level. The REBA score can also provide how quickly action needs to be taken for each REBA score.

4.     RULA

RULA is an acronym for Rapid Upper Limb Assessment. This tool was developed by Dr. Lynn McAtamney and Professor E. Nigel Corlett which was published in 1993 in the Applied Ergonomics Journal.  Very similarly to the REBA tool, this tool was designed so that health and safety professionals could assess lifting in the field. The tool is mainly focused on posture. Using a series of mathematical calculations and a series of tables, each activity is assigned a RULA score. To calculate the RULA score, the tool separates the body parts into two groups: Group A and Group B. The body parts assigned to Group A are:

·      Upper Arm

·      Lower Arm

·      Wrist Position

The body parts assigned to group B are:

·      Neck Position

·      Trunk Position

·      Legs

Using the score of each body part posture in group A, locate the score in Table A to assign a Group A Posture Score. This score is then added to the Muscle Use Score and the Force/Load Score which assigns the Wrist and Arm Score.

Using the score of each body part posture in group B, locate the score in Table b to assign a Group B Posture Score. This score is then added to the Muscle Use Score and Force/Load Score which equals the Neck, Trunk, Leg Score.

Using Table C, locate the Wrist/Arm score in the Y-axis and the Neck, Trunk, Leg Score on the X-axis to determine the RULA score. The RULA score is a numerical value between 1 and 7. If the RULA score returns a 1 or 2, the posture is acceptable but if the RULA score is a 7, changes are needed.

Equipment to Reduce Risk of Injury

To help mitigate the risk of injury from manual material handling there are devices which can be used to help mitigate some of the risk of manual material handling.

Exoskeletons

Exoskeletons are devices which can be used to supplement the human body when completing tasks which require repetitive motions or using strength to complete a job. There are two types of exoskeletons: Powered and Passive. Powered Exoskeletons are powered using a battery which will supplement the strength needed for lifting materials. Passive Exoskeletons are non-powered devices that are focused on a specific muscle group.

Overhead Cranes

Overhead Cranes or workstation cranes can drastically decrease the exposure to workers for lifting and moving heavy objects. These devices can assist the worker by mechanically lifting, lowering, turning, or moving a heavy object to a different location.

Handles & Grip Aids

When lifting heavy materials, the grip matters. By using handles, the grip could drastically change the posture of the lift. It can also reduce pressure points while lifting.

Forklifts

Forklifts are powered vehicles (gas, diesel, electric) that are often used in facilities to move heavy items. The truck can pick up significantly heavier objects compared to the human and move it to a new location. Since the forks can be adjusted, the height of the lift can also be adjusted so that employees can lift in a more neutral position. The use of forklifts can eliminate or reduce some exposures of manual material handling.

Pallet Jacks

Pallet jacks are a great tool that can assist in moving heavy objects. Pallet jacks can be both powered and manual, so it is important to understand the weight being moved. If the weight exceeds the amount a person can easily push/pull, alternative means should be considered such as a forklift or a powered pallet jack.

Adjustable Workstations

The workstation height is critical to posture and preferred ergonomic principles. If the workstation is properly adjusted, it can prevent bending over and exposing the worker to awkward posture. Having an adjustable workstation can also allow the employee to adjust the height based on their height so that they can perform their work using good ergonomic principle.

Ways to Reduce Risk of Injury

The safest way to manual materials handling is to eliminate any manual handling of materials using the Hierarchy of Control. There will be times where elimination is not an option. Below are some ways to reduce the risk of injury if manual materials handling is present.

Stretch and Flex Programs

Stretch and Flex programs are designed to help reduce workplace injuries. Using a stretch and flex program allows the worker to properly warm up before exerting lots of energy in their normal workdays. When properly stretched and warming up, the workers heartrate increases which in returns blood flow, nutrients, and oxygen to muscle groups. When the body is properly warmed up, muscle injuries are less likely to occur. Physical and Occupational therapists can be contracted to help develop a Stretch and Flex Program that is best suited for the work taking place.

Rest and Recovery

Just like any muscle use, it is critical to provide the muscles proper rest to allow for them to recover properly. One key mitigation effort would be proper rest. Getting a good nights sleep is critical to help employees reduce workplace injuries from manual material handling. Throughout the day, employees should incorporate breaks to allow for their muscles to rest and so that the employees can rehydrate and rest to prevent fatigue.

Another principle that employers can use is a job rotation. These tasks will only expose the workers to fatigue in certain muscles groups instead of repetitively working the same muscle group. Allowing employees to rotate jobs will allow for longer rest and recovery and can potentially lessen the exposure to manual handling of materials.

Safe Manual Materials