|
Drill And Tap Size Chart
Below is a comprehensive drill and tap size chart for all drills and taps, imperial and metric, up to in diameter. In manufactured parts, holes with female screw threads are often needed; they accept male screws to facilitate the building and fastening of a finished assembly. One of the most common ways to produce such threaded holes is to drill a hole of appropriate size with a drill bit and then tap it with a tap. Each standard size of female screw thread has one or several corresponding drill bit sizes that are within the range of appropriate size—slightly larger than the minor diameter of the mating male thread, but smaller than its pitch and major diameters. Such an appropriately sized drill is called a tap drill for that size of thread, because it is a correct drill to be followed by the tap. Many thread sizes have several possible tap drills, because they yield threads of varying thread depth between 50% and 100%. Usually thread depths of 60% to 75% are desired ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Glow Plug (model Engine)
A glow plug engine, or glow engine, is a type of small internal combustion engine typically used in model aircraft, model cars and similar applications. The ignition is accomplished by a combination of heating from compression, heating from a glow plug and the catalytic effect of the platinum within the glow plug on the methanol within the fuel. History German inventor Ray Arden invented the first glow plug for model engines in 1947. Model glow plug design The glow plugs used in model engines are significantly different from those used in full-size diesel engines. In full-size engines, the glow plug is used only for starting. In model engines, the glow plug is an integral part of the ignition system because of the catalytic effect of the platinum wire. The glow plug is a durable, mostly platinum, helical wire filament recessed into the plug's tip. When an electric current runs through the plug, or when exposed to the heat of the combustion chamber, the filament glows, enab ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Hole Making
A hole is an opening in or through a particular medium, usually a solid body. Holes occur through natural and artificial processes, and may be useful for various purposes, or may represent a problem needing to be addressed in many fields of engineering. Depending on the material and the placement, a hole may be an indentation in a surface (such as a hole in the ground), or may pass completely through that surface (such as a hole created by a hole puncher in a piece of paper). Types Holes can occur for a number of reasons, including natural processes and intentional actions by humans or animals. Holes in the ground that are made intentionally, such as holes made while searching for food, for replanting trees, or postholes made for securing an object, are usually made through the process of digging. Unintentional holes in an object are often a sign of damage. Potholes and sinkholes can damage human settlements. Holes can occur in a wide variety of materials, and at a wide ran ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
United States Standard Thread
United States Standard thread (USS thread), also known as Sellers Standard thread, Franklin Institute thread and American Standard thread, is a standard for inch based threaded fasteners and washers. The USS standard is no longer supported. It, together with the SAE fastener standard, was incorporated into the Unified Thread Standard. However, the term, ''USS'', continues to be used occasionally today to describe inch based threaded fasteners with a coarse thread pitch and inch based washers that are a little bit larger than the corresponding SAE washer. The Unified Thread Standard uses the term UNC (Unified Coarse) to describe a fastener that previously would have been designated USS and the Unified Thread Standard uses the term UNF (Unified Fine) to describe a fastener that would have previously been designated SAE. Thread form The thread form is defined by flats at the tip and root of the thread form. This flat length is defined as the pitch divided by eight. The thread depth ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Taps And Dies
Taps and dies are tools used to create screw threads, which is called threading. Many are cutting tools; others are forming tools. A tap is used to cut or form the female portion of the mating pair (e.g. a nut). A die is used to cut or form the male portion of the mating pair (e.g. a bolt). The process of cutting or forming threads using a tap is called ''tapping'', whereas the process using a die is called ''threading''. Both tools can be used to clean up a thread, which is called ''chasing''. However, using an ordinary tap or die to clean threads generally removes some material, which results in looser, weaker threads. Because of this, machinists generally clean threads with special taps and dies—called ''chasers''—made for that purpose. Chasers are made of softer materials and don't cut new threads. However they still fit tighter than actual fasteners, and are fluted like regular taps and dies so debris can escape. Car mechanics, for example, use chasers on spark plug th ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
National Pipe Thread
American National Standard Pipe Thread standards, often called national pipe thread standards for short, are United States national technical standards for screw threads used on threaded pipes and Piping and plumbing fitting, pipe fittings. They include both screw thread#Taper, tapered and straight thread series for various purposes, including rigidity, pressure-tight sealing, or both. The types are named with a full name and an abbreviation, such as NPT, NPS, NPTF, or NPSC. MIP is an abbreviation for male iron pipe, and FIP is an abbreviation for female iron pipe. Outside North America, some US pipe thread sizes are widely used, as well as many British Standard Pipe threads and International Organization for Standardization, ISO 7-1, 7-2, 228-1, and 228-2 threads. Types The various types are each named with a abbreviation and a full name, as follows: Uses Threaded pipes can provide an effective seal for pipes transporting liquids, gases, steam, and hydraulic fluid. These th ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Drill Bit Sizes
Drill bits are the cutting tools of drilling machines. They can be made in any size to order, but standards organizations have defined sets of sizes that are produced routinely by drill bit manufacturers and stocked by distributors. In the U.S., fractional inch and gauge drill bit sizes are in common use. In nearly all other countries, metric drill bit sizes are most common, and all others are anachronisms or are reserved for dealing with designs from the US. The British Standards on replacing gauge size drill bits with metric sizes in the UK was first published in 1959. A comprehensive table for metric, fractional wire and tapping sizes can be found at the drill and tap size chart. Metric drill bit sizes Metric drill bit sizes define the diameter of the bit in terms of standard metric lengths. Standards organizations define sets of sizes that are conventionally manufactured and stocked. For example, British Standard BS 328 defines 230 sizes from 0.2 mm to 25.0 mm. F ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
British Standard Whitworth
British Standard Whitworth (BSW) is an imperial-unit-based screw thread standard, devised and specified by Joseph Whitworth in 1841 and later adopted as a British Standard. It was the world's first national screw thread standard, and is the basis for many other standards, such as BSF, BSP, BSCon, and BSCopper. History The Whitworth thread was the world's first national screw thread standard, devised and specified by Joseph Whitworth in 1841. Until then, the only standardization was what little had been done by individual people and companies, with some companies' in-house standards spreading a bit within their industries. Whitworth's new standard specified a 55° thread angle and a thread depth of 0.640327''p'' and a radius of 0.137329''p'', where ''p'' is the pitch. The thread pitch increases with diameter in steps specified on a chart. The Whitworth thread system was later to be adopted as a British Standard to become British Standard Whitworth (BSW). An example of the ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
British Association Screw Threads
British Association screw threads, or BA screw threads, are a set of small screw threads, the largest being 0BA at 6 mm diameter. They were, and to some extent still are, used for miniature instruments and modelling. They are unusual in that they were probably the most "scientific" design of screw, starting with 0BA at 6.0 mm diameter and 1.0 mm pitch and progressing in a geometric sequence where each larger number was 0.9 times the pitch of the last size. They then rounded to 2 significant figures in metric and then converting to inches and rounding to the thousandth of an inch. This anticipated worldwide metrication by about a century. The design was first proposed by the British Association in 1884 with a thread angle and depth based on the Swiss Thury thread, it was adopted by the Association in 1903. The Thury thread was different in that it went both positive and negative all the way up to a size of −20 which was 75.2 mm diameter by 8.23 mm pitch ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
British Standard Pipe Thread
British Standard Pipe (BSP) is a set of technical standards for screw threads that has been adopted internationally for interconnecting and sealing pipes and fittings by mating an external (male) thread with an internal (female) thread. It has been adopted as standard in plumbing and pipe fitting, except in North America, where NPT and related threads are used. Types Two types of threads are distinguished: * Parallel (straight) threads, ''British Standard Pipe Parallel thread'' (''BSPP''; originally also known as ''British Standard Pipe Fitting thread''/''BSPF'' and ''British Standard Pipe Mechanical thread''/''BSPM''), which have a constant diameter; denoted by the letter ''G''. * Taper threads, ''British Standard Pipe Taper thread'' (''BSPT''), whose diameter increases or decreases along the length of the thread; denoted by the letter ''R''. These can be combined into two types of joints: ; Jointing threads: These are pipe threads where pressure-tightness is made through t ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
AN Thread
The AN thread (also A-N) is a particular type of fitting used to connect flexible hoses and rigid metal tubing that carry fluid. It is a US military-derived specification that dates back to World War II and stems from a joint standard agreed upon by the Army and Navy, hence AN. The Army-Navy involvement is also the origin of the red/blue color combination that was traditionally used in the anodized finishing process. AN sizes range from -2 (dash two) to -32 in irregular steps, with each step equating to the OD (outside diameter) of the tubing in -inch increments. Therefore, a -8 AN size would be equal to -inch OD tube. However, this system does not specify the ID (inside diameter) of the tubing because the tube wall can vary in thickness. Each AN size also uses its own standard thread size. AN fittings are a flare fitting, using 37° flared tubing to form a metal-to-metal seal. They are similar to other 37° flared fittings, such as JIC, which is their industrial variant. The ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
Inches
Measuring tape with inches The inch (symbol: in or ″) is a unit of length in the British imperial and the United States customary systems of measurement. It is equal to yard or of a foot. Derived from the Roman uncia ("twelfth"), the word ''inch'' is also sometimes used to translate similar units in other measurement systems, usually understood as deriving from the width of the human thumb. Standards for the exact length of an inch have varied in the past, but since the adoption of the international yard during the 1950s and 1960s the inch has been based on the metric system and defined as exactly 25.4 mm. Name The English word "inch" ( ang, ynce) was an early borrowing from Latin ' ("one-twelfth; Roman inch; Roman ounce"). The vowel change from Latin to Old English (which became Modern English ) is known as umlaut. The consonant change from the Latin (spelled ''c'') to English is palatalisation. Both were features of Old English phonology; see and ... [...More Info...] [...Related Items...] OR: [Wikipedia] [Google] [Baidu] |
