manually connecting calls with cord pairs at a telephone switchboard]]
A telephone exchange, telephone switch, or central office is a telecommunications
system used in the public switched telephone network
(PSTN) or in large enterprises. It interconnects telephone subscriber lines or virtual circuits of digital systems to establish telephone call
s between subscribers.
In historical perspective, telecommunication terms have been used with different semantics over time. The term ''telephone exchange'' is often used synonymously with ''central office'', a Bell System
term. Often, a ''central office'' is defined as a building used to house the inside plant
equipment of potentially several telephone exchanges, each serving a certain geographical area. Such an area has also been referred to as the exchange or exchange area. In North America, a central office location may also be identified as a ''wire center'', designating a facility to which a telephone is connected and obtains dial tone
. For business and billing purposes, telecommunication carriers define ''rate centers'', which in larger cities may be clusters of central offices, to define specified geographical locations for determining distance measurements.
In the United States and Canada, the Bell System established in the 1940s a uniform nationwide numbering system
of identifying central offices with a three-digit central office code and a three-digit numbering plan area
code (NPA code, or area code). Central office codes were unique in each numbering plan area. The NPA code and the central office code were used as prefixes in subscriber telephone numbers. With the development of international and transoceanic telephone trunks, especially driven by direct customer dialing, similar efforts of systematic organization of the telephone networks occurred in many countries in the mid-20th century.
For corporate or enterprise use, a private telephone exchange is often referred to as a private branch exchange
(PBX), when it has connections to the public switched telephone network
. A PBX is installed in enterprise facilities, typically near large office spaces or within an organizational campus to serve the organization's telephones and any private leased line circuits. Smaller installations might deploy a PBX or key telephone system
in the office of a receptionist.
[[File:Telephone switchboard cross-switching (Rankin Kennedy, Electrical Installations, Vol V, 1903).jpg|thumb|1903 manual switch for four subscriber lines (top) with four cross-bar talking circuits (horizontal), and one bar to connect the operator (T). The lowest cross-bar connects idle stations to ground to enable the signaling indicators (F).]]
In the era of the electrical telegraph, its principal users were post offices, railway stations, the more important governmental centers (ministries), stock exchanges, very few nationally distributed newspapers, the largest internationally important corporations, and wealthy individuals.
''The Sydney Morning Herald'', credited to ''The Times'', April 19, 1878, p. 6.
Despite the fact that telephone devices existed before the invention of the telephone exchange, their success and economical operation would have been impossible on the same schema
and structure of the contemporary telegraph, as prior to the invention of the telephone exchange switchboard, early telephones were hardwired to and communicated with only a single other telephone (such as from an individual's home to the person's business).
A telephone exchange is a telephone system located at service centers (central offices) responsible for a small geographic area that provided the switching or interconnection of two or more individual subscriber lines for calls made between them, rather than requiring direct lines between subscriber stations. This made it possible for subscribers to call each other at homes, businesses, or public spaces. These made telephones an available and comfortable communication tool for everyday use, and it gave the impetus for the creation of a whole new industrial sector. Telephone lines that were common at the time which were shared by neighbors and were called party lines. Only one person was able to use the telephone at a time. Telephones would also be in general stores, with people able to go to the store and talk. Telephones were not readily available at first but became an asset to communication.0
As with the invention of the telephone
itself, the honour of "first telephone exchange" has several claimants. One of the first to propose a telephone exchange was Hungarian Tivadar Puskás
in 1877 while he was working for Thomas Edison
. The first experimental telephone exchange was based on the ideas of Puskás, and it was built by the Bell Telephone Company
in 1877. The world's first state-administered telephone exchange opened on November 12, 1877 in Friedrichsberg close to Berlin
under the direction of Heinrich von Stephan
. George W. Coy
designed and built the first commercial US telephone exchange which opened in New Haven, Connecticut
in January, 1878. The switchboard was built from "carriage bolts, handles from teapot lids and bustle wire" and could handle two simultaneous conversations. Charles Glidden
is also credited with establishing an exchange in Lowell, MA. with 50 subscribers in 1878.
In Europe other early telephone exchanges were based in London
, both of which opened under Bell patents in 1879. Belgium had its first International Bell
exchange (in Antwerp
) a year later.
In 1887 Puskás introduced the multiplex switchboard
Later exchanges consisted of one to several hundred plug boards
staffed by switchboard operator
s. Each operator sat in front of a vertical panel containing banks of ¼-inch tip-ring-sleeve
(3-conductor) jacks, each of which was the local termination of a subscriber
's telephone line
. In front of the jack panel lay a horizontal panel containing two rows of patch cords, each pair connected to a cord circuit
When a calling party
lifted the receiver, the local loop current lit a signal lamp near the jack.
The operator responded by inserting the rear cord (''answering cord'') into the subscriber's jack and switched her headset into the circuit to ask, "Number, please?" For a local call, the operator inserted the front cord of the pair (''ringing cord'') into the called party's local jack and started the ringing cycle. For a long-distance call, she plugged into a trunk
circuit to connect to another operator in another bank of boards or at a remote central office. In 1918, the average time to complete the connection for a long-distance call was 15 minutes.
Early manual switchboards required the operator to operate listening keys and ringing keys, but by the late 1910s and 1920s, advances in switchboard technology led to features which allowed the call to be automatically answered immediately as the operator inserted the answering cord, and ringing would automatically begin as soon as the operator inserted the ringing cord into the called party's jack. The operator would be disconnected from the circuit, allowing her to handle another call, while the caller heard an audible ringback signal, so that that operator would not have to periodically report that she was continuing to ring the line.
In the ringdown
method, the originating operator called another intermediate operator who would call the called subscriber, or passed it on to another intermediate operator.
This chain of intermediate operators could complete the call only if intermediate trunk lines were available between all the centers at the same time. In 1943 when military calls had priority, a cross-country US call might take as long as 2 hours to request and schedule in cities that used manual switchboards for toll calls.
On March 10, 1891, Almon Brown Strowger
, an undertaker in Kansas City, Missouri
, patented the stepping switch
, a device which led to the automation of telephone circuit switching. While there were many extensions and adaptations of this initial patent, the one best known consists of 10 levels or banks, each having 10 contacts arranged in a semicircle. When used with a rotary telephone dial
, each pair of digits caused the shaft of the central contact "hand" of the stepping switch to first step (ratchet) up one level for each pulse in the first digit and then to swing horizontally in a contact row with one small rotation for each pulse in the next digit.
Later stepping switches were arranged in banks, the first stage of which was a ''linefinder
''. If one of up to a hundred subscriber lines (two hundred lines in later linefinders) had the receiver lifted "off hook", a linefinder connected the subscriber's line to a free first selector, which returned the subscriber a dial tone
to show that it was ready to receive dialled digits. The subscriber's dial pulsed at about 10 pulses per second, although the speed depended on the standard of the particular telephone administration.
Exchanges based on the Strowger switch were eventually challenged by other exchange types
and later by crossbar
technology. These exchange designs promised faster switching and would accept inter-switch pulses faster than the Strowger's typical 10 pps—typically about 20 pps. At a later date many also accepted DTMF
"touch tones" or other tone signaling systems.
A transitional technology (from pulse to DTMF) had converters to convert DTMF to pulse, to feed to older Strowger, panel, or crossbar switches. This technology was used as late as mid-2002.
Many terms used in telecommunication technology differ in meaning and usage among the various English speaking regions.
For the purpose of this article the following definitions are made:
* ''Manual service'' is telephone service in which a human telephone operator
routes calls as instructed by a subscriber with a telephone set that does not have a dial.
* ''Dial service'' is when an exchange routes calls by interpreting subscriber-dialed digits.
* A ''telephone switch'' is the switching equipment of an exchange.
* A ''wire center'' is the area served by a particular switch or central office.
* A ''concentrator
'' is a device that concentrates traffic, be it remote or co-located with the switch.
* An ''off-hook
'' condition represents a circuit that is in use, e.g., when a telephone call is in progress.
* An ''on-hook
'' condition represents an idle circuit, i.e. no telephone call is in progress.
A ''central office'' originally was a primary exchange in a city with other exchanges service parts of the area. The term became to mean any switching system including its facilities and operators. It is also used generally for the building that houses switching and related inside plant
equipment. In United States telecommunication
jargon, a central office (C.O.) is a common carrier switching center Class 5 telephone switch
in which trunks and local loop
s are terminated and switched.
[Source: from Federal Standard 1037C.]
In the UK, a ''telephone exchange'' means an exchange building, and is also the name for a telephone switch.
Manual service exchanges
With manual service, the customer lifts the receiver off-hook
and asks the operator
to connect the call to a requested number. Provided that the number is in the same central office, and located on the operator's switchboard, the operator connects the call by plugging the ringing cord into the jack corresponding to the called customer's line. If the called party's line is on a different switchboard in the same office, or in a different central office, the operator plugs into the trunk for the destination switchboard or office and asks the operator answering (known as the "B" operator) to connect the call.
Most urban exchanges provided common-battery
service, meaning that the central office provided power to the subscriber telephone circuits for operation of the transmitter, as well as for automatic signaling with rotary dial
s. In common-battery systems, the pair of wires from a subscriber's telephone to the exchange carry 48V (nominal) DC potential from the telephone company end across the conductors. The telephone presents an open circuit when it is on-hook
[Connected to a switch, an off-hook condition operates a relay to connect the line to a dial tone generator and a device to collect dialed digits.]
When a subscriber's phone is off-hook, it presents an electrical resistance across the line which causes current to flow through the telephone and wires to the central office. In a manually operated switchboard, this current flowed through a relay coil, and actuated a buzzer or a lamp on the operator's switchboard, signaling the operator to perform service.
In the largest cities, it took many years to convert every office to automatic equipment, such as a panel switch
. During this transition period, once numbers were standardized to the
2L-4N or 2L-5N
format (two-letter exchange name and either four or five digits), it was possible to dial a number located in a manual exchange and be connected without requesting operator assistance. The policy of the Bell System
stated that customers in large cities should not need to be concerned with the type of office, whether they were calling a manual or an automatic office.
When a subscriber dialed the number of a manual station, an operator at the destination office answered the call after seeing the number on an indicator
, and connected the call by plugging a cord into the outgoing circuit and ringing the destination station. For example, if a dial customer calling from TAylor 4725 dialed a number served by a manual exchange, e.g., ADams 1383-W, the call was completed, from the subscriber's perspective, exactly as a call to LEnnox 5813, in an automated exchange. The party line letters W, R, J, and M were only used in manual exchanges with jack-per-line party lines.
In contrast to the listing format ''MAin 1234'' for an automated office with two capital letters, a manual office, having listings such as Hillside 834 or East 23, was recognizable by the format in which the second letter was not capitalized.
Rural areas, as well as the smallest towns, had manual service and signaling was accomplished with magneto
telephones, which had a crank for the signaling generator. To alert the operator, or another subscriber on the same line, the subscriber turned the crank to generate ringing current. The switchboard responded by interrupting the circuit, which dropped a metal tab above the subscriber's line jack and sounded a buzzer. Dry cell
batteries, normally two large N°. 6 cells in the subscriber's telephone, provided the direct current for the transmitter. Such magneto systems were in use in the US as late as 1983, as in the small town, Bryant Pond, Woodstock, Maine
Many small town magneto systems featured party lines
, anywhere from two to ten or more subscribers sharing a single line. When calling a party, the operator used code ringing, a distinctive ringing signal
sequence, such as two long rings followed by one short ring. Everyone on the line could hear the signals, and could pick up and monitor other people's conversations.
Early automatic exchanges
Automatic exchanges, or dial service, were invented by Almon Strowger
in 1888 and first used commercially in 1892. Their purpose was to eliminate the need for human switchboard operator
s who completed the connections required for a telephone call
. Automation replaced human operators with electromechanical systems and telephones were equipped with a dial by which a caller transmitted the destination telephone number to the automatic switching system.
A telephone exchange automatically senses an off-hook condition of the telephone
when the user removes the handset from the switchhook or cradle. The exchange provides dial tone
at that time to indicate to the user that the exchange is ready to receive dialed digits. The pulses or DTMF
tones generated by the telephone are processed and a connection is established to the destination telephone within the same exchange or to another distant exchange.
The exchange maintains the connection until one of the parties hangs up. This monitoring of connection status is called ''supervision.'' Additional features, such as billing equipment, may also be incorporated into the exchange.
The Bell System dial service implemented a feature called automatic number identification
(ANI) which facilitated services like automated billing, toll-free 800-numbers
, and 9-1-1
service. In manual service, the operator knows where a call is originating by the light on the switchboard jack field. Before ANI, long-distance calls were placed into an operator queue and the operator asked the calling party's number and recorded it on a paper toll ticket.
Early exchanges were electromechanical systems using motors, shaft drives, rotating switches and relays
. Some types of automatic exchanges were the Strowger switch
or step-by-step switch, All Relay, X-Y, panel switch
, Rotary system
and the crossbar switch
Circuits interconnecting switches are called ''trunks''. Before Signalling System 7
, Bell System
electromechanical switches in the United States originally communicated with one another over trunks using a variety of DC voltages and signaling tones, replaced today by digital signals.
Some signaling communicated dialed digits. An early form called Panel Call Indicator
Pulsing used quaternary
pulses to set up calls between a panel switch
and a manual switchboard. Probably the most common form of communicating dialed digits between electromechanical switches was sending dial pulse
s, equivalent to a rotary dial
's pulsing, but sent over trunk circuits between switches.
In Bell System trunks, it was common to use 20 pulse-per-second between crossbar switches and crossbar tandems. This was twice the rate of Western Electric/Bell System telephone dials. Using the faster pulsing rate made trunk utilization more efficient because the switch spent half as long listening to digits. DTMF was not used for trunk signaling.
was the last of the pre-digital methods. It used a different set of tones sent in pairs like DTMF. Dialing was preceded by a special ''keypulse'' (KP) signal and followed by a ''start'' (ST). Variations of the Bell System MF tone scheme became a CCITT
standard. Similar schemes were used in the Americas and in some European countries including Spain. Digit strings between switches were often abbreviated to further improve utilization.
For example, one switch might send only the last four or five digits of a telephone number
. In one case, seven digit numbers were preceded by a digit 1 or 2 to differentiate between two area codes or office codes, (a two-digit-per-call savings). This improved revenue per trunk and reduced the number of digit receivers needed in a switch. Every task in electromechanical switches was done in big metallic pieces of hardware. Every fractional second cut off of call set up time meant fewer racks of equipment to handle call traffic.
Examples of signals communicating supervision or call progress include E and M signaling
, SF signaling, and robbed-bit signaling. In physical (not carrier) E and M trunk circuits, trunks were four wire. Fifty trunks would require a hundred pair cable between switches, for example. Conductors in one common circuit configuration were named tip, ring, ear (E) and mouth (M). Tip and ring were the voice-carrying pair, and named after the tip and ring on the three conductor cords on the manual operator's console.
In two-way trunks with E and M signaling, a handshake took place to prevent both switches from colliding by dialing calls on the same trunk at the same time. By changing the state of these leads from ground to -48 volts, the switches stepped through a handshake protocol. Using DC voltage changes, the local switch would send a signal to get ready for a call and the remote switch would reply with an acknowledgment (a wink) to go ahead with dial pulsing. This was done with relay logic and discrete electronics.
These voltage changes on the trunk circuit would cause pops or clicks that were audible to the subscriber as the electrical handshaking stepped through its protocol. Another handshake, to start timing for billing purposes, caused a second set of clunks when the called party answered.
A second common form of signaling for supervision was called single-frequency or ''SF signaling''. The most common form of this used a steady 2,600 Hz tone to identify a trunk as idle. Trunk circuitry hearing a 2,600 Hz tone for a certain duration would go idle. (The duration requirement reduced falsing
.) Some systems used tone frequencies over 3,000 Hz, particularly on SSB frequency division multiplex microwave radio relay
digital transmission systems, bits within the T-1 data stream were used to transmit supervision. By careful design, the appropriated bits did not change voice quality appreciably. Robbed bits were translated to changes in contact states (opens and closures) by electronics in the channel bank hardware. This allowed direct current E and M signaling, or dial pulses, to be sent between electromechanical switches over a digital carrier which did not have DC continuity.
A characteristic of electromechanical switching equipment is that the maintenance staff could hear the mechanical clattering of Strowgers, panel switches or crossbar relays. During heavy use periods, it could be difficult to converse in a central office switch room due to the clatter of calls being processed in a large switch. For example, on Mother's Day in the US, or on a Friday evening around 5pm, the metallic rattling could make raised voices necessary. For wire spring relay markers
these noises resembled hail falling on a metallic roof.
On a pre-dawn Sunday morning, call processing might slow to the extent that one might be able to hear individual calls being dialed and set up. There were also noises from whining power inverters and whirring ringing generators. Some systems had a continual, rhythmic "clack-clack-clack" from wire spring relay
s that made reorder
(120 ipm) and busy (60 ipm) signals.
Bell System installations typically had alarm bells, gongs, or chimes to announce alarms calling attention to a failed switch element. A trouble reporting card system was connected to switch common control elements. These trouble reporting systems punctured cardboard cards
with a code that logged the nature of a failure. Reed relay
technology in stored program control
exchange finally quieted the environment.
Electromechanical switching systems required sources of electricity in form of direct current (DC), as well as alternating ring current (AC), which were generated on-site with mechanical generators. In addition, telephone switches required adjustment of many mechanical parts. Unlike modern switches, a circuit connecting a dialed call through an electromechanical switch had DC continuity within the local exchange area via metallic conductors.
The design and maintenance procedures of all systems involved methods to avoid that subscribers experienced undue changes in the quality of the service or that they noticed failures. A variety of tools referred to as ''make-busy''s were plugged into electromechanical switch elements upon failure and during repairs. A make-busy identified the part being worked on as in-use, causing the switching logic to route around it. A similar tool was called a ''TD tool.'' Delinquent subscribers had their service temporarily denied (TDed). This was effected by plugging a tool into the subscriber's office equipment on Crossbar systems or line group in step-by-step switches. The subscriber could receive calls but could not dial out.
Strowger-based, step-by-step offices in the Bell System required continuous maintenance, such as cleaning. Indicator lights on equipment bays alerted staff to conditions such as blown fuses (usually white lamps) or a permanent signal
(stuck off-hook condition, usually green indicators). Step offices were more susceptible to single-point failures than newer technologies.
Crossbar offices used more shared, common control circuits. For example, a digit receiver (part of an element called an ''Originating Register'') would be connected to a call just long enough to collect the subscriber's dialed digits. Crossbar architecture was more flexible than step offices. Later crossbar systems had punch-card-based trouble reporting systems. By the 1970s, ''automatic number identification
'' had been retrofitted to nearly all step-by-step and crossbar switches in the Bell System.
Electronic switching system
s gradually evolved in stages from electromechanical hybrids with stored program control
to the fully digital systems. Early systems used reed relay
-switched metallic paths under digital control. Equipment testing, phone numbers reassignments, circuit lockouts
and similar tasks were accomplished by data entry on a terminal.
Examples of these systems included the Western Electric 1ESS switch
, Northern Telecom SP1
, Ericsson AXE, Automatic Electric EAX-1 & EAX-2, Philips PRX
/A, ITT Metaconta, British GPO/BT TXE
series and several other designs were similar. Ericsson also developed a fully computerized version of their ARF crossbar exchange called ARE. These used a crossbar switching matrix with a fully computerized control system and provided a wide range of advanced services. Local versions were called ARE11 while tandem versions were known as ARE13. They were used in Scandinavia, Australia, Ireland and many other countries in the late 1970s and into the 1980s when they were replaced with digital technology.
These systems could use the old electromechanical signaling methods inherited from crossbar and step-by-step switches. They also introduced a new form of data communications: two 1ESS exchanges could communicate with one another using a data link called Common Channel Interoffice Signaling, (CCIS)
. This data link was based on CCITT 6, a predecessor to SS7
In European systems R2 signalling was normally used.
First concepts of digital switching and transmission were developed by various labs in the United States and in Europe starting in the 1930s. The first prototype digital switch was developed by Bell Labs
as part of the ESSEX project while the first true digital exchange to be combined with digital transmission systems was designed by LCT (Laboratoire Central de Telecommunications) in Paris. The first digital switch to be placed into a public network in England was the Empress Exchange in London
which was designed by the General Post Office
research labs. It was a tandem switch that connected three Strowger
exchanges. The first commercial roll-out of a fully digital local switching system was Alcatel
's E10 system which began serving customers in Brittany
in Northwestern France in 1972.
Prominent examples of digital switches include:
's AXE telephone exchange
is the most widely used digital switching platform in the world and can be found throughout Europe and in most countries around the world. It is also very popular in mobile applications. This highly modular system was developed in Sweden in the 1970s as a replacement for the very popular range of Ericsson crossbar switch
es ARF, ARM, ARK and ARE used by many European networks from the 1950s onwards.
inherited three of the world's most iconic digital switching systems : Alcatel
, and the Western Electric 5ESS
:Alcatel developed the E10 system in France during the late 1960s and 1970s. This widely used family of digital switches was one of the earliest TDM switches to be widely used in public networks. Subscribers were first connected to E10A switches in France in 1972. This system is used in France, Ireland, China, and many other countries. It has been through many revisions and current versions are even integrated into All IP
:Alcatel also acquired ITT System 12
which when it bought ITT's European operations. The S12 system and E10 systems were merged into a single platform in the 1990s. The S12 system is used in Germany, Italy, Australia, Belgium, China, India, and many other countries around the world.
:Finally, when Alcatel and Lucent merged, the company acquired Lucent's 5ESS
systems used throughout the United States of America and in many other countries.
*Nokia Siemens Networks EWSD
originally developed by Siemens
and for the German market is used throughout the world.
, and now Ribbon Communications DMS100
and other versions are very popular with operators all over the world.
* GTD-5 EAX developed by GTE Automatic Electric, the GTD-5 was acquired by Lucent which became Alcatel-Lucent, which then became Nokia
NEAX used in Japan, New Zealand and many other countries.
*Marconi System X
originally developed by GPT and Plessey is a type of digital exchange used by BT Group
in the UK public telephone network.
) used by an operator to offer local and long-distance services in France
. Each switch typically serves 10,000–100,000+ subscribers depending on the geographic area]]
Digital switches encode the speech going on, in 8,000 time slices per second. At each time slice, a digital Pulse-code modulation|PCM
representation of the tone is made. The digits are then sent to the receiving end of the line, where the reverse process occurs, to produce the sound for the receiving phone. In other words, when someone uses a telephone, the speaker's voice is "encoded" then reconstructed for the person on the other end. The speaker's voice is delayed in the process by a small fraction of one second — it is not "live", it is reconstructed — delayed only minutely.
Individual local loop
telephone lines are connected to a remote concentrator
. In many cases, the concentrator is co-located in the same building as the switch. The interface between remote concentrators and telephone switches has been standardised by ETSI
as the V5
protocol. Concentrators are used because most telephones are idle most of the day, hence the traffic from hundreds or thousands of them may be concentrated into only tens or hundreds of shared connections.
Some telephone switches do not have concentrators directly connected to them, but rather are used to connect calls between other telephone switches. These complex machines are referred to as "carrier-level" switches or tandem switch
Some telephone exchange buildings in small towns house only ''remote'' or ''satellite'' switches, and are homed upon a "parent" switch, usually several kilometres away. The remote switch is dependent on the parent switch for routing. Unlike a digital loop carrier
, a remote switch can route calls between local phones itself, without using trunks to the parent switch.
right|thumb|300px|Map of the Central Office locations in the US
The switch's place in the network
Telephone switches are a small component of a large network. A major part, in terms of expense, maintenance, and logistics of the telephone system is outside plant
, which is the wiring outside the central office. While many subscribers were served with party-lines in the middle of the 20th century, it was the goal that each subscriber telephone station were connected to an individual pair of wires from the switching system.
A typical central office may have tens of thousands of pairs of wires that appear on terminal blocks called the main distribution frame
(MDF). A component of the MDF is protection: fuses or other devices that protect the switch from lightning, shorts with electric power lines, or other foreign voltages. In a typical telephone company, a large database tracks information about each subscriber pair and the status of each jumper. Before computerization of Bell System records in the 1980s, this information was handwritten in pencil in accounting ledger books.
To reduce the expense of outside plant, some companies use "pair gain
" devices to provide telephone service to subscribers. These devices are used to provide service where existing copper facilities have been exhausted or by siting in a neighborhood, can reduce the length of copper pairs, enabling digital services such as Integrated Services Digital Network
(ISDN) or digital subscriber line
Pair gain or digital loop carrier
s (DLCs) are located outside the central office, usually in a large neighborhood distant from the CO. DLCs are often referred to as Subscriber Loop Carrier
s (SLCs), after a Lucent
DLCs can be configured as universal (UDLCs) or integrated (IDLCs). ''Universal DLC''s have two terminals, a central office terminal (COT) and a remote terminal (RT), that function similarly. Both terminals interface with analog signals, convert to digital signals, and transport to the other side where the reverse is performed.
Sometimes, the transport is handled by separate equipment. In an ''Integrated DLC'', the COT is eliminated. Instead, the RT is connected digitally to equipment in the telephone switch. This reduces the total amount of equipment required.
Switches are used in both local central offices and in long distance
centers. There are two major types in the Public switched telephone network
(PSTN), the Class 4 telephone switch
es designed for toll or switch-to-switch connections, and the Class 5 telephone switches
or subscriber switches, which manage connections from subscriber telephones. Since the 1990s, hybrid Class 4/5 switching systems that serve both functions have become common.
Another element of the telephone network is time and timing. Switching, transmission and billing equipment may be slaved to very high accuracy 10 MHz standards
which synchronize time events to very close intervals. Time-standards equipment may include Rubidium- or Caesium-based standards and a Global Positioning System
Long-distance switches may use a slower, more efficient switch-allocation algorithm than local central offices
, because they have near 100% utilization of their input and output channels. Central offices have more than 90% of their channel capacity unused.
Traditional telephone switches connected physical circuits (e.g., wire pairs) while modern telephone switches use a combination of space-
and time-division switching. In other words, each voice channel is represented by a time slot
(say 1 or 2) on a physical wire pair (A or B). In order to connect two voice channels (say A1 and B2) together, the telephone switch interchanges the information between A1 and B2. It switches both the time slot and physical connection. To do this, it exchanges data between the time slots and connections 8,000 times per second, under control of digital logic that cycles through electronic lists of the current connections. Using both types of switching makes a modern switch far smaller than either a space or time switch could be by itself.
The structure of a switch
is an odd number of layers of smaller, simpler subswitches. Each layer is interconnected by a web of wires that goes from each subswitch, to a set of the next layer of subswitches. In some designs, a physical (space) switching layer alternates with a time switching layer. The layers are symmetric, because in a telephone system callers can also be called
. Other designs use time-switching only, throughout the switch.
A time-division subswitch reads a complete cycle of time slots into a memory, and then writes it out in a different order, also under control of a cyclic computer memory. This causes some delay in the signal.
A space-division subswitch switches electrical paths, often using some variant of a nonblocking minimal spanning switch
, or a crossover switch
Switch control algorithms
Fully connected mesh network
One way is to have enough switching fabric
to assure that the pairwise allocation will always succeed by building a fully connected mesh network
. This is the method usually used in central office switches, which have low utilization of their resources.
Clos's nonblocking switch algorithm
The connections between layers of subswitches of telephone switching system are scarce resources, allocated by special control logic in a fault tolerant
manner. Clos network
s are often used.
Composite switches are inherently fault-tolerant. If a subswitch fails, the controlling computer can sense it during a periodic test. The computer marks all the connections to the subswitch as "in use". This prevents new calls, and does not interrupt old calls that remain working. As calls in progress end, the subswitch becomes unused, and new calls avoid the subswitch because it's already "in use." Some time later, a technician can replace the circuit board. When the next test succeeds, the connections to the repaired subsystem are marked "not in use", and the switch returns to full operation.
To prevent frustration with unsensed failures, all the connections between layers in the switch are allocated using first-in-first-out lists
(queues). As a result, if a connection is faulty or noisy and the customer hangs up and redials, they will get a different set of connections and subswitches. A last-in-first-out
(stack) allocation of connections might cause a continuing string of very frustrating failures.
Fire and disaster recovery
The central exchange, due to the system's design, is almost always a single point of failure
for local calls. As the capacity of individual switches and the optical fibre
which interconnects them increases, potential disruption caused by destruction of one local office will only be magnified. Multiple fibre connections can be used to provide redundancy to voice and data connections between switching centres, but careful network design is required to avoid situations where a main fibre and its backup both go through the same damaged central office as a potential common mode failure
* History of telecommunication
* List of telephone switches
* Pair gain system
* Full availability, limited availability and gradings
* Plesiochronous digital hierarchy
* Telephone exchange names
* Faraday Building
– First telephone exchange in UK
* Automatic call distributor
20. “1870s-1940s-Telephone.” Imagining the Internet,
Telephone Central Office History and PicturesTelephone World's Central Office Building Pictures
* ttp://www.google.com/patents?id=xL9WAAAAEBAJ&dq=252576 patent 252,576 for the first telephone switchboard in 1881A Telecom Exchange Tour in NZ