R Tronic

A semi-automatic transmission is a "theoretical" multiple-speed transmission where part of its operation is automated (typically the actuation of the clutch), but the driver's input would be required to launch the vehicle from a standstill and to manually change gears. Semi-automatic transmissions were exclusively used in motorcycles and are based on conventional manual transmissions or sequential manual transmissions, but use an automatic clutch system. But some semi-automatic transmissions have also been based on standard hydraulic automatic transmissions with torque converters and planetary gearsets.

Names for specific types of semi-automatic transmissions include ''clutchless manual'', ''auto-manual'', ''auto-clutch manual'', and ''paddle-shift'' transmissions. These systems facilitate gear shifts for the driver by operating the clutch system automatically, usually via switches that trigger an actuator or servo, while still requiring the driver to manually shift gears. This contrasts with a preselector gearbox, in which the driver operates the clutch and selects the next gear ratio, but the gear change within the transmission is performed automatically.

The first usage of semi-automatic transmissions was in automobiles, increasing in popularity in the mid-1930s when they were offered by several American car manufacturers. Less common than traditional hydraulic automatic transmissions, semi-automatic transmissions have nonetheless been made available on various car and motorcycle models and have remained in production throughout the 21st century. Semi-automatic transmissions with paddle shift operation have been used in various racing cars, and were first introduced to control the electro-hydraulic gear shift mechanism of the Ferrari 640 Formula One car in 1989. These systems are currently used on a variety of top-tier racing car classes; including Formula One, IndyCar, and touring car racing. Other applications include motorcycles, trucks, buses, and railway vehicles.

Design and operation

Semi-automatics facilitate easier gear shifts by removing the need to depress a clutch pedal or lever at the same time as changing gears. Depending on the mechanical build, design, and age of the vehicle, they can use anything from hydraulic, pneumatic or electric actuators, electrical switches, motors, and processors, or a combination of any such systems, to execute gear shifts on demand when requested by the driver, which is typically initiated when the driver moves the gear stick. Most cars that have a semi-automatic transmission are not fitted with a standard clutch pedal since the clutch is remotely controlled. Similarly, most motorcycles with a semi-automatic transmission are not fitted with a conventional clutch lever on the handlebar.

Clutchless manual transmissions

Most semi-automatic transmissions are based on conventional manual transmissions, but are usually operated with an automatic clutch or another kind of partially automated transmission mechanism. Once the clutch becomes automated, the transmission becomes semi-automatic. However, these systems still require manual gear selection by the driver. This type of transmission is called a ''clutchless manual'' or an ''automated manual''.

Most semi-automatic transmissions in older passenger cars retain the normal H-pattern shifter of a manual transmission; similarly, semi-automatic transmissions on older motorcycles retain the conventional foot-shift lever, as on a motorcycle with a fully manual transmission. However, semi-automatics systems in newer motorcycles, racing cars, and other types of vehicles often use gear selection methods such as shift paddles near the steering wheel or triggers near the handlebars.

Several different forms of automation for clutch actuation have been used over the years, from hydraulic, pneumatic, and electromechanical clutches to vacuum-operated, electromagnetic, and even centrifugal clutches. Fluid couplings (most commonly and formerly used in early automatic transmissions) have also been used by various manufacturers, usually alongside some form of mechanical friction clutch, to prevent the vehicle from stalling when coming to a standstill or at idle.

A typical semi-automatic transmission design may work by using Hall effect sensors or micro switches to detect the direction of the requested shift when the gear stick is used. These sensors' output, combined with the output from a sensor connected to the gearbox which measures its current speed and gear, is fed into a transmission control unit, electronic control unit, engine control unit, or microprocessor, or another type of electronic control system. This control system then determines the optimal timing and torque required for smooth clutch engagement.

The electronic control unit powers an actuator, which engages and disengages the clutch in a smooth manner. In some cases, the clutch is actuated by a servomotor coupled to a gear arrangement for a linear actuator, which, via a hydraulic cylinder filled with hydraulic fluid from the braking system, disengages the clutch. In other cases, the internal clutch actuator may be completely electric, where the main clutch actuator is powered by an electric motor or solenoid, or even pneumatic, where the main clutch actuator is a pneumatic actuator that disengages the clutch.

A clutchless manual system, named the ''Autostick'', was a semi-automatic transmission introduced by Volkswagen for the 1968 model year. Marketed as the ''Volkswagen Automatic Stickshift'', a conventional three-speed manual transmission was connected to a vacuum-operated automatic clutch system. The top of the gear stick was designed to easily depress and activate an electric switch, i.e. when touched by the driver's hand. When pressed, the switch operated a 12-volt solenoid, which in turn operated the vacuum clutch actuator, thus disengaging the clutch and allowing shifting between gears. With the driver's hand removed from the gearshift, the clutch would re-engage automatically. The transmission was also equipped with a torque converter, allowing the car to idle in gear like with an automatic, as well as stop and start from a standstill in any gear.

Automated manual transmissions

Starting in the late 1990s, automotive manufacturers introduced what is now called an automated manual transmission (AMT), which is mechanically similar to, and has its roots in, earlier clutchless manual transmission systems. An AMT functions in the same way as older semi-automatic and clutchless manual transmissions, but with two exceptions; it is able to both operate the clutch and shift automatically, and does not use a torque converter. Shifting is done either automatically from a transmission control unit (TCU), or manually from either the shift knob or shift paddles mounted behind the steering wheel. AMTs combine the fuel efficiency of manual transmissions with the shifting ease of automatic transmissions. Their biggest disadvantage is poor shifting comfort due to the mechanical clutch being disengaged by the TCU, which is easily noticeable as "jolting". Some transmission makers have tried solving this issue by using oversized synchronizer rings and not fully opening the clutch during shifting—which works in theory, but as of 2007, there have not been any series production cars with such functions. In passenger cars, modern AMTs generally have six speeds (though some have seven) and a rather long gearing. In combination with a smart-shifting program, this can significantly reduce fuel consumption. In general, there are two types of AMTs: integrated AMTs and add-on AMTs. Integrated AMTs were designed to be dedicated AMTs, whereas add-on AMTs are conversions of standard manual transmissions into AMTs.

An automated manual transmission may include a fully automatic mode where the driver does not need to change gears at all. These transmissions can be described as a standard manual transmission with an automated clutch and automated gear shift control, allowing them to operate in the same manner as traditional automatic transmissions. The TCU automatically shifts gears if, for example, the engine is redlined. The AMT can be switched to a clutchless manual mode wherein one can upshift or downshift using a console-mounted shift selector or paddle shifters. It has a lower cost than conventional automatic transmissions.

These transmissions are not to be confused with "manumatic" automatic transmissions, which are marketed under trade names such as ''Tiptronic'', ''Steptronic'', ''Sportmatic'', and ''Geartronic''. While these systems seem superficially similar, they are closer in design to automatic transmissions than manual transmissions.

Sequential manual transmissions

Several semi-automatic transmissions used by motorcycles and racing cars are actually mechanically based on sequential manual transmissions. Semi-automatic motorcycle transmissions generally omit the clutch lever, but retain the conventional heel-and-toe foot shift lever.

Semi-automatic motorcycle transmissions are based on conventional sequential manual transmissions and typically use a centrifugal clutch. At idle speed, the engine is disconnected from the gearbox input shaft, allowing both it and the bike to freewheel—unlike with torque converter automatics, there is no idle creep with a properly adjusted centrifugal clutch. As the engine speed rises, counterweights within the clutch assembly gradually pivot further outwards until they start to make contact with the inside of the outer housing and transmit an increasing amount of engine power and torque. The effective "bite point" or "biting point" is found automatically by equilibrium, where the power is transmitted through the (still-slipping) clutch is equal to what the engine can provide. This allows relatively fast full-throttle takeoffs (with the clutch adjusted so the engine is at peak torque) without the engine slowing or being bogged down, as well as more relaxed starts and low-speed maneuvers at lower throttle and RPMs.

Usage in passenger cars

1900s—1920s

In 1901, Amédée Bollée developed a method of shifting gears that did not require the use of a clutch and was activated by a ring mounted within the steering wheel. One car using this system was the 1912 Bollée Type F Torpedo.

1930s—1940s

Prior to the arrival of the first mass-produced hydraulic automatic transmission (the General Motors Hydra-Matic) in 1940, several American manufacturers offered various devices to reduce the amount of clutch or shifting input required. These devices were intended to reduce the difficulty of operating the unsynchronised manual transmissions, or "crash gearboxes", that were commonly used, especially in stop-start driving.

An early step towards automated transmissions was the 1933–1935 REO Self-Shifter, which automatically shifted between two forward gears in the "forward" mode (or between two shorter gear ratios in the "emergency low" mode). Standing starts required the driver to use the clutch pedal. The Self-Shifter first appeared in May 1933 and was offered as standard on the Royale and as an option on the Flying Cloud S-4.

In 1937, the four-speed Oldsmobile Automatic Safety Transmission was introduced on the Oldsmobile Six and Oldsmobile Eight models. It used a planetary gearset with a clutch pedal for starting from a standstill and switching between the "low" and "high" ranges. The Automatic Safety Transmission was replaced by the fully-automatic Hydra-Matic for the 1940 model year.

The 1938–1939 Buick Special was available with another Self-Shifter 4-speed semi-automatic transmission, which used a manual clutch for starting from standstill and an automated clutch for gear changes.

The 1941 Chrysler M4 Vacamatic transmission was a two-speed manual transmission with an integral underdrive unit, a traditional manual clutch, and a fluid coupling between the engine and the clutch. The two-speed transmission had "high" and "low" ranges, and the clutch was used when the driver wanted to switch between ranges. For normal driving, the driver would press the clutch, select the High range, and then release the clutch. Once the accelerator was pressed, the fluid coupling would engage and the car would begin moving forward, with the underdrive unit engaged to provide a lower gear ratio. At between , the driver would lift off the accelerator and the underdrive unit would disengage. The Vacamatic was replaced by a similar M6 Presto-Matic transmission for the 1946 model year.

Similar designs were used for the 1941–1950 Hudson Drive-Master and the ill-fated 1942 Lincoln Liquimatic. Both of these combined a 3-speed manual transmission with automated shifting between the 2nd and 3rd gears, instead of the Vacamatic's "underdrive" unit.

The Packard Electro-Matic, introduced in the 1941 Packard Clipper and Packard 180, was an early clutchless manual transmission that used a traditional friction clutch with automatic vacuum operation, which was controlled by the position of the accelerator.

1950s–1960s

The automotive products manumatic system, available on the 1953 Ford Anglia 100E, was a vacuum-powered automatic clutch system that was actuated by a switch that was triggered whenever the gear stick was moved. The system could control the throttle cable (to keep the engine at the required RPM for the gear change) and vary the rate of clutch engagement. The successive Newtondrive system, available on the 1957–1958 Ford Anglia, also had a provision for choke control. A similar product was the German Saxomat automatic clutch system, which was introduced in the mid-1950s and available on various European cars.

The Citroën DS, introduced in 1955, used a hydraulic system with a hydraulically-operated speed controller and idle speed step-up device to select gears and operate the otherwise conventional clutch. This allowed clutchless shifting with a single column-mounted selector, while the driver simultaneously lifted off the accelerator to change gear. This system was nicknamed "Citro-Matic" in the U.S.

For the 1962 model year, American Motors introduced the E-Stick, which eliminated the clutch pedal in the Rambler American with standard three-speed manual transmissions. This automatic clutch used engine oil pressure as a hydraulic source and was available for less than $60. Compared to fully automatic transmissions of the time, the E-Stick offered the fuel economy of a stick-shift, with vacuum and electric switches controlling the clutch. The E-Stick three-speed transmission was offered on the larger Rambler Classic models, along with an overdrive unit. The system was only available with 6-cylinder engines, and the lack of a clutch proved unpopular, so it was discontinued after 1964.

The 1967 Volkswagen WSK (''Wandlerschaltkupplungsgetriebe''; English: ''Torque converter shift/clutch gearbox''), used in the Beetle and Karmann Ghia, was one of the first gearboxes of its kind, with an automatic mechanical clutch and a torque converter. Shifting was done manually by the driver. The automatic mechanical clutch allowed the car to accelerate from a stop, whereas the torque converter enabled it to do so in any gear. Dampening engine vibrations and providing torque multiplication, it functioned as a sort of "reduction gearbox", so the actual mechanical gearbox only needed three forward gears (this is why conventional automatic transmissions with torque converters normally have fewer gears than manual transmissions). The WSK had no "first" gear; instead, the first gear was converted into reverse gear, and the second gear was labeled first (with the third and fourth gears respectively being labeled second and third).

The Chevrolet Torque-Drive transmission, introduced on the 1968 Chevrolet Nova and Camaro, is one of a few examples where a semi-automatic transmission was based on a conventional hydraulic automatic transmission (rather than a standard manual transmission). The Torque-Drive was essentially a 2-speed Powerglide automatic transmission without the vacuum modulator, requiring the driver to manually shift gears between "Low" and "High". The quadrant indicator on Torque-Drive cars was "Park-R-N-Hi-1st". The driver would start the car in "1st," then move the lever to "Hi" when desired. The Torque-Drive was discontinued at the end of 1971 and replaced by a traditional hydraulic automatic transmission. Other examples of semi-automatic transmissions based on hydraulic automatics were the Ford 3-speed Semi-Automatic Transmission used in the 1970–1971 Ford Maverick, early versions of Honda's 1976–1988 Hondamatic 2-speed and 3-speed transmissions, and the Daihatsu Diamatic 2-speed transmission used in the 1985–1991 Daihatsu Charade.

Other examples

Usage in motorcycles

An early example of a semi-automatic motorcycle transmission was the use of an automatic centrifugal clutch in the early 1960s by the Czechoslovakian manufacturer Jawa Moto. Their design was used without permission in the 1965 Honda Cub 50, which resulted in Jawa suing Honda for patent infringement and Honda agreeing to pay royalties for each motorcycle using the design.

Other semi-automatic transmissions used in motorcycles include:
* Honda's Hondamatic two-speed transmission fitted with a torque converter (which shares its name with several fully-automatic transmissions), as used in its 1976 CB750A, 1977 CB400A Hawk, 1978 CM400A and 1982 CM450A.
* Those in various minibikes, including the Amstar Nostalgia 49, Honda CRF50F, Z series, and ST series, Kawasaki KLX-110, KLX-110R, and KSR110, KTM 65 SX, Suzuki DR-Z50, DR-Z70, and DR-Z125, SSR SR110TR, and Yamaha TT-R50E.
* Yamaha used an automatic clutch system called YCCS on motorcycles such as the 2006 Yamaha FJR1300AE sports-touring. This system can be shifted either with the lever in the traditional position near the left foot or with a switch accessible to the left hand where the clutch lever would go on traditional motorcycles.
* The Can-Am Spyder Roadster's SE5 and SE6 5-speed and 6-speed transmissions.
* Those in several underbone motorcycles in the 1970s; the Suzuki FR50, Suzuki FR80, and Yamaha Townmate used 3-speed transmissions with a heel-and-toe gear shift.
* Some high-performance sport bikes use a trigger-shift system, with a handlebar-mounted trigger, paddle, switch, or button, and an automatically operated clutch.
* Some dirt bikes use this system, which is sometimes referred to as an auto-clutch transmission. These include the Honda CRF110F and Yamaha TT-R110E. The conventional motorcycle foot shifter is retained, but the manual hand-clutch lever is no longer required. Semi-automatic transmissions in dirt bikes may be referred to as "automatic" despite a lack of automatic shifting.

Usage in motorsports

Semi-automatic transmissions in racing cars are typically operated by shift paddles connected to a designated transmission control unit.

The first Formula One car to use a semi-automatic transmission was the 1989 Ferrari 640. It used hydraulic actuators and electrical solenoids for clutch control and shifting, and was shifted via two paddles mounted behind the steering wheel. Another paddle on the steering wheel controlled the clutch, which was only needed when starting from a standstill. The car won its debut race at the Brazilian Grand Prix, but for much of the season suffered from reliability problems. Other teams began switching to similar semi-automatic transmissions; the 1991 Williams FW14 was the first to use a sequential drum-rotation mechanism (similar to those used in motorcycle transmissions), which allowed for a more compact design that required only one actuator to rotate the drum and change gears. A further development was made possible by the introduction of electronic throttle control soon after, which made it possible for the car to automatically rev-match during downshifts. By 1993, most teams were using semi-automatic transmissions. The last F1 car fitted with a conventional manual gearbox, the Forti FG01, raced in 1995.

Following concerns about the potential for Formula One cars to shift gears automatically without any driver input, mandatory software was introduced in 1994 that ensured that gear changes only occurred when instructed by the driver. Pre-programmed, computer-controlled, fully-automatic upshifts and downshifts were re-introduced and allowed from 2001, and were permitted from that year's Spanish Grand Prix, but were banned again in 2004. Buttons on the steering wheel to shift directly to a particular gear (instead of having to shift sequentially using the paddles) are permitted. The 2005 Minardi PS05, Renault R25, and Williams FW27 were the last Formula 1 cars to use a 6-speed gearbox before the switch to a mandatory 7-speed gearbox for the 2006 season. Since 2014 season, Formula 1 cars currently use mandatory 8-speed paddle-shift gearboxes.

The now-defunct CART Champ Car Series switched from a lever-shift sequential system to a 7-speed paddle-shift system for the 2007 season. This transmission was introduced with the new-for-2007 Panoz DP01 chassis.

The rival IndyCar Series introduced their 6-speed semi-automatic paddle-shift system for the 2008 season, also replacing the previous lever-shifted sequential transmission, introduced with the Dallara IR-05 chassis for 2008. IndyCars currently use the Xtrac P1011 sequential transmission, which uses a semi-automatic paddle shift system supplied by Mega-Line called AGS (Assisted Gearshift System). AGS uses a pneumatic gearshift and clutch actuator controlled by an internal transmission control unit.

Both the FIA Formula 2 and Formula 3 Championships currently use 6-speed sequential gearboxes with electro-hydraulic operation via shift paddles. Manual control of the multi-plate clutch systems via a lever behind the steering wheel is used to launch the cars.

DTM currently uses a Hewland DTT-200 6-speed sequential transmission with steering-wheel-mounted shift paddles, which was introduced for the 2012 season with the new rule change. This new system replaced the older lever-shifted sequential transmission, which had been used for the previous 12 seasons (since 2000).

Usage in other vehicles

Other notable uses for semi-automatic transmissions include:
* During the 1940s to 1960s, many small diesel shunting locomotives used epicyclic semi-automatic transmissions. For example, the British Rail Class 03 and British Rail Class 04 used the Wilson-Drewry CA5 R7 transmission.
* The Sinclair S.S.S. Powerflow, used from the 1950s to the early 1960s in Huwood-Hudswell diesel mining locomotives, the British Rail Class D2/7 and the British Rail Class D2/12. The Powerflow design is of the layshaft type with constant-mesh gears and dog clutch engagement, allowing it to provide seamless power delivery during upshifts. This transmission was also used in some road vehicles.
* The Self-Changing Gears Pneumocyclic, an epicyclic transmission built in the United Kingdom from the 1960s to the 1980s. Using a similar design to the company's previous preselector gearboxes, the Pneumocyclic transmission was used in several buses, such as the Leyland Leopard, Panther, and Tiger. It was also fitted to several thousand British diesel railcars during this time.
* All-terrain vehicles, such as the Honda ATC185, Honda ATC200, Honda TRX90X and TRX250X (Honda SportClutch), Suzuki LT125D Quadrunner (also known as the Suzuki QuadRunner 125), Suzuki LT 230, Suzuki Eiger 400, Yamaha Big Bear 250, 350, and 400, Yamaha Grizzly 80, Yamaha Raptor 80, Yamaha YFB250 Timberwolf, the Yamaha Moto-4 ATV range, and the Yamaha Tri-Moto range.
**The Honda Electric Shift Program is used in ATVs such as the 1998 Honda TRX450FE (also called the Foreman 450ES ESP) and first-generation Honda Rincon. Shifting is accomplished by pressing one of the two gear selector arrows on the left handlebar, which activates an electric shifting system.

See also

* Automated manual transmission (AMT)
* Automatic transmission (AT)
* Dual-clutch transmission (DCT)
* Manumatic
* Shift time

References

{{DEFAULTSORT:Semi-automatic transmission
Automotive transmission technologies
Automobile transmissions
Motorcycle transmissions
Mechanical power control