Pulsed DC
   HOME

TheInfoList



OR:

Pulsed DC (PDC) or pulsating direct current is a periodic current which changes in value but never changes direction. Some authors use the term pulsed DC to describe a signal consisting of one or more rectangular ("flat-topped"), rather than sinusoidal, pulses. Pulsed DC is commonly produced from AC (
alternating current Alternating current (AC) is an electric current which periodically reverses direction and changes its magnitude continuously with time in contrast to direct current (DC) which flows only in one direction. Alternating current is the form in whic ...
) by a half-wave rectifier or a
full-wave rectifier A rectifier is an electrical device that converts alternating current (AC), which periodically reverses direction, to direct current (DC), which flows in only one direction. The reverse operation (converting DC to AC) is performed by an inver ...
. Full wave rectified ac is more commonly known as Rectified AC. PDC has some characteristics of both
alternating current Alternating current (AC) is an electric current which periodically reverses direction and changes its magnitude continuously with time in contrast to direct current (DC) which flows only in one direction. Alternating current is the form in whic ...
(AC) and
direct current Direct current (DC) is one-directional flow of electric charge. An electrochemical cell is a prime example of DC power. Direct current may flow through a conductor such as a wire, but can also flow through semiconductors, insulators, or eve ...
(DC) waveforms. The
voltage Voltage, also known as electric pressure, electric tension, or (electric) potential difference, is the difference in electric potential between two points. In a static electric field, it corresponds to the work needed per unit of charge to ...
of a DC wave is roughly constant, whereas the voltage of an AC waveform continually varies between positive and negative values. Like an AC wave, the voltage of a PDC wave continually varies, but like a DC wave, the sign of the voltage is constant. Pulsating direct current is used on PWM controllers.


Smoothing

Most modern electronic items function using a DC voltage, so the PDC waveform must usually be smoothed before use. A reservoir capacitor converts the PDC wave into a DC waveform with some superimposed
ripple Ripple may refer to: Science and technology * Capillary wave, commonly known as ripple, a wave traveling along the phase boundary of a fluid ** Ripple, more generally a disturbance, for example of spacetime in gravitational waves * Ripple (electri ...
. When the PDC voltage is initially applied, it charges the capacitor, which acts as a short term storage device to keep the output at an acceptable level while the PDC waveform is at a low voltage. Voltage regulation is often also applied using either
linear Linearity is the property of a mathematical relationship ('' function'') that can be graphically represented as a straight line. Linearity is closely related to '' proportionality''. Examples in physics include rectilinear motion, the linear ...
or switching regulation.


Difference from AC

Pulsating direct current has an average value equal to a constant (DC) along with a time-dependent pulsating component added to it, while the average value of alternating current is zero in steady state (or a constant if it has a DC offset, value of which will then be equal to that offset). Devices and circuits may respond differently to pulsating DC than they would to non-pulsating DC, such as a battery or regulated power supply and should be evaluated.


Uses

Pulsed DC may also be generated for purposes other than rectification. It is often used to reduce
electric arc An electric arc, or arc discharge, is an electrical breakdown of a gas that produces a prolonged electrical discharge. The current through a normally nonconductive medium such as air produces a plasma; the plasma may produce visible light. An ...
s when generating thin
carbon Carbon () is a chemical element with the symbol C and atomic number 6. It is nonmetallic and tetravalent—its atom making four electrons available to form covalent chemical bonds. It belongs to group 14 of the periodic table. Carbon mak ...
films, and for increasing yield in
semiconductor fabrication Semiconductor device fabrication is the process used to manufacture semiconductor devices, typically integrated circuit (IC) chips such as modern computer processors, microcontrollers, and memory chips such as NAND flash and DRAM that are p ...
by reducing
electrostatic Electrostatics is a branch of physics that studies electric charges at rest ( static electricity). Since classical times, it has been known that some materials, such as amber, attract lightweight particles after rubbing. The Greek word for amb ...
build-up. It is also generated by the
voltage regulator A voltage regulator is a system designed to automatically maintain a constant voltage. A voltage regulator may use a simple feed-forward design or may include negative feedback. It may use an electromechanical mechanism, or electronic components ...
s in some
automobile A car or automobile is a motor vehicle with wheels. Most definitions of ''cars'' say that they run primarily on roads, seat one to eight people, have four wheels, and mainly transport people instead of goods. The year 1886 is regarde ...
s, e.g., the classic air-cooled
Volkswagen Beetle The Volkswagen Beetle—officially the Volkswagen Type 1, informally in German (meaning "beetle"), in parts of the English-speaking world the Bug, and known by many other nicknames in other languages—is a two-door, rear-engine economy car, ...
. Pulsed DC is also commonly used in driving light-emitting diodes (LEDs) to lower the intensity. Since light-emitting diodes cannot be reliably dimmed through the simple reduction of voltage as in an incandescent bulb, pulsed DC is used to produce many rapid flashes of light that to the human eye are indiscernible as individual flashes, but are seen as a lower brightness. Since an LED has no traditional filament to stress, this also has the added effect of prolonging the lifespan of the LED by reducing its on-time. This can sometimes be seen on videos where an LED or lamp assembly composed of LEDs is filmed at a frame rate very close to - but not exactly - the same as the pulsed DC frequency, which causes the lamp to slowly and occasionally fade in and out as the LEDs fall out of synchronization with the video frame.


References


Bibliography

* Electric power Electric current {{electronics-stub