Propellant transfer

An orbital propellant depot is a cache of propellant that is placed in orbit around Earth or another body to allow spacecraft or the transfer stage of the spacecraft to be fueled in space. It is one of the types of space resource depots that have been proposed for enabling infrastructure-based space exploration.
Many different depot concepts exist depending on the type of fuel to be supplied, location, or type of depot which may also include a propellant tanker that delivers a single load to a spacecraft at a specified orbital location and then departs. In-space fuel depots are not necessarily located near or at a space station.

Potential users of in-orbit refueling and storage facilities include space agencies, defense ministries and communications satellite or other commercial companies.

Satellite servicing depots would extend the lifetime of satellites that have nearly consumed all of their orbital maneuvering fuel and are likely placed in a geosynchronous orbit. The spacecraft would conduct a space rendezvous with the depot, or ''vice versa'', and then transfer propellant to be used for subsequent orbital maneuvers. In 2011, Intelsat showed interest in an initial demonstration mission to refuel several satellites in geosynchronous orbit, but all plans have been since scrapped.

A low earth orbit (LEO) depot's primary function would be to provide propellant to a transfer stage headed to the moon, Mars, or possibly a geosynchronous orbit. Since all or a fraction of the transfer stage propellant can be off-loaded, the separately launched spacecraft with payload and/or crew could have a larger mass or use a smaller launch vehicle. With a LEO depot or tanker fill, the size of the launch vehicle can be reduced and the flight rate increased—or, with a newer mission architecture where the beyond-Earth-orbit spacecraft also serves as the second stage, can facilitate much larger payloads—which may reduce the total launch costs since the fixed costs are spread over more flights and fixed costs are usually lower with smaller launch vehicles. A depot could also be placed at Earth-Moon Lagrange point 1 (EML-1) or behind the Moon at EML-2 to reduce costs to travel to the moon or Mars. Placing a depot in Mars orbit has also been suggested.

LEO depot fuels

For rockets and space vehicles, propellants usually take up 2/3 or more of their total mass.

Large upper-stage rocket engines generally use a cryogenic fuel like liquid hydrogen and liquid oxygen (LOX) as an oxidizer because of the large specific impulse possible, but must carefully consider a problem called "boil off," or the evaporation of the cryogenic propellant. The boil off from only a few days of delay may not allow sufficient fuel for higher orbit injection, potentially resulting in a mission abort. Lunar or Mars missions will require weeks to months to accumulate tens of thousands to hundreds of thousands of kilograms of propellant, so additional equipment may be required on the transfer stage or the depot to mitigate boiloff.

Non-cryogenic, earth-storable liquid rocket propellants including RP-1 (kerosene), hydrazine and nitrogen tetroxide (NTO), and mildly cryogenic, space-storable propellants like liquid methane and liquid oxygen, can be kept in liquid form with less boiloff than the cryogenic fuels, but also have lower specific impulse. Additionally, gaseous or supercritical propellants such as those used by ion thrusters include xenon, argon, and bismuth.

Propellant launch costs

Ex-NASA administrator Mike Griffin commented at the 52nd AAS Annual Meeting in Houston, November 2005, that "at a conservatively low government price of $10,000/kg in LEO, 250 MT of fuel for two missions per year is worth $2.5 B, at government rates."

If one assumes that a 130 tonne launch vehicle could be flown twice a year for $2.5B, the price is about $10,000/kg.

Cryogenic depot architectures and types

In the depot-centric architecture, the depot is filled by tankers, and then the propellant is transferred to an upper stage prior to orbit insertion, similar to a gas station filled by tankers for automobiles. By using a depot, the launch vehicle size can be reduced and the flight rate increased. Since the accumulation of propellant may take many weeks to months, careful consideration must be given to boiloff mitigation.

In simple terms, a passive cryogenic depot is a transfer stage with stretched propellant tanks, additional insulation, and a sun shield. In one concept, hydrogen boiloff is also redirected to reduce or eliminate liquid oxygen boiloff and then used for attitude control, power, or reboost. An active cryogenic depot is a passive depot with additional power and refrigeration equipment/cryocoolers to reduce or eliminate propellant boiloff. Other active cryogenic depot concepts include electrically powered attitude control equipment to conserve fuel for the end payload.

Heavy lift versus depot-centric architectures

In the heavy lift architecture, propellant, which can be two thirds or more of the total mission mass, is accumulated in fewer launches and possibly shorter time frame than the depot centric architecture. Typically the transfer stage is filled directly and no depot is included in the architecture. For cryogenic vehicles and cryogenic depots, additional boiloff mitigation equipment is typically included on the transfer stage, reducing payload fraction and requiring more propellant for the same payload unless the mitigation hardware is expended.

Heavy Lift is compared with using Commercial Launch and Propellant Depots in this power point by Dr. Alan Wilhite given at FISO Telecon.

Feasibility of propellant depots

Both theoretical studies and funded development projects that are currently underway aim to provide insight into the feasibility of propellant depots. Studies have shown that a depot-centric architecture with smaller launch vehicles could be less expensive than a heavy-lift architecture over a 20-year time frame. The cost of large launch vehicles is so high that a depot able to hold the propellant lifted by two or more medium-sized launch vehicles may be cost effective and support more payload mass on beyond-Earth orbit trajectories.

In a 2010 NASA study, an additional flight of an Ares V heavy launch vehicle was required to stage a US government Mars reference mission due to 70 tons of boiloff, assuming 0.1% boiloff/day for hydrolox propellant. The study clearly identified the need to decrease the design boiloff rate by an order of magnitude or more.

Approaches to the design of low Earth orbit (LEO) propellant depots were also discussed in the 2009 Augustine report to NASA, which "examined the hencurrent concepts for in-space refueling."HSF Final Report: Seeking a Human Spaceflight Program Worthy of a Great Nation
, October 2009, ''Review of U.S. Human Spaceflight Plans Committee'', p. 65-66. The report determined there are essentially two approaches to refueling a spacecraft in LEO:
* Propellant tanker delivery. In this approach, a single tanker performs a rendezvous and docking with an on-orbit spacecraft. The tanker then transfers propellant, then departs. This approach is "much like an airborne tanker refuels an aircraft."
* In-space depot. An alternative approach is for many tankers to rendezvous and transfer propellant to an orbital depot. Then, at a later time, a spacecraft may dock with the depot and receive a propellant load before departing Earth orbit.
Both approaches were considered feasible with 2009 spaceflight technology, but anticipated that significant further engineering development and in-space demonstration would be required before missions could depend on the technology. Both approaches were seen to offer the potential of long-term life-cycle savings.

In 2010 United Launch Alliance (ULA) proposed their Advanced Cryogenic Evolved Stage (ACES) tanker, a concept that dates back to work by Boeing in 2006, sized to transport up to of propellant—in early design with first flight planned for no earlier than 2023, with initial usage as a propellant tanker potentially beginning in the mid-2020s. ACES was not funded, but some of the ideas were used in the Centaur stage of the Vulcan Centaur rocket.

Beyond theoretical studies, since at least 2017, SpaceX has undertaken funded development of an interplanetary set of technologies. While the interplanetary mission architecture consists of a combination of several elements that are considered by SpaceX to be key to making long-duration beyond Earth orbit (BEO) spaceflights possible by reducing the cost per ton delivered to Mars by multiple orders of magnitude over what NASA approaches have achieved,

refilling of propellants in orbit is one of the four key elements. In a novel mission architecture, the SpaceX design intends to enable the long-journey spacecraft to expend almost all of its propellant load during the launch to low Earth orbit while it serves as the second stage of the SpaceX Starship, and then after refilling on orbit by multiple Starship tankers, provide the large amount of energy required to put the spacecraft onto an interplanetary trajectory. The Starship tanker is designed to transport approximately of propellant to low Earth orbit. In April 2021, NASA selected the SpaceX Lunar Starship with in-orbit refuelling for their initial lunar human landing system.

Advantages

Because a large portion of a rocket is propellant at time of launch, proponents point out several advantages of using a propellant depot architecture. Spacecraft could be launched unfueled and thus require less structural mass, or the depot tanker itself could serve as the second-stage on launch when it is reusable. An on-orbit market for refueling may be created where competition to deliver propellant for the cheapest price takes place, and it may also enable an economy of scale by permitting existing rockets to fly more often to refuel the depot. If used in conjunction with a mining facility on the moon, water or propellant could be exported back to the depot, further reducing the cost of propellant. An exploration program based on a depot architecture could be cheaper and more capable, not needing a specific rocket or a heavy lift such as the SLS to support multiple destinations such as the Moon, Lagrange points, asteroids, and Mars.

NASA studies in 2011 showed cheaper and faster alternatives than the Heavy Lift Launch System and listed the following advantages:
* Tens of billions of dollars of cost savings to fit the budget profile
* Allows first NEA/Lunar mission by 2024 using conservative budgets
* Launch every few months rather than once every 12–18 months
* Allows multiple competitors for propellant delivery
* Reduced critical path mission complexity (AR&Ds, events, number of unique elements)

History and plans

USA

Propellant depots were proposed as part of the Space Transportation System (along with nuclear "tugs" to take payloads from LEO to other destinations) in the mid-1960s.Dewar, James. "To The End Of The Solar System: The Story Of The Nuclear Rocket". Apogee, 2003

In October 2009, the Air Force and United Launch Alliance (ULA) performed an experimental on-orbit demonstration on a modified Centaur upper stage on the DMSP-18 launch to improve "understanding of propellant settling and slosh, pressure control, RL10 chilldown and RL10 two-phase shutdown operations." "The light weight of DMSP-18 allowed of remaining LO₂ and LH₂ propellant, 28% of Centaur’s capacity," for the on-orbit demonstrations. The post-spacecraft mission extension ran 2.4 hours before executing the deorbit burn.Successful Flight Demonstration Conducted by the Air Force and United Launch Alliance Will Enhance Space Transportation: DMSP-18
''United Launch Alliance'', October 2009, accessed January 10, 2011.

NASA's Launch Services Program is working on an ongoing slosh fluid dynamics experiments with partners called CRYOTE. , ULA is also planning additional in-space laboratory experiments to further develop cryogenic fluid management technologies using the Centaur upper stage after primary payload separation. Named CRYOTE, or CRYogenic Orbital TEstbed, it will be a testbed for demonstrating a number of technologies needed for cryogenic propellant depots, with several small-scale demonstrations planned for 2012-2014.
, ULA says this mission could launch as soon as 2012 if funded.

The ULA CRYOTE small-scale demonstrations are intended to lead to a ULA large-scale cryo-sat flagship technology demonstration in 2015.

The Future In-Space Operations (FISO) Working Group, a consortium of participants from NASA, industry and academia, discussed propellant depot concepts and plans on several occasions in 2010,Future In-Space Operations (FISO) Working Group presentations
, FISO, 2011-01-07, accessed January 10, 2011.
with presentations of optimal depot locations for human space exploration beyond low Earth orbit,Potential Propellant Depot Locations Supporting Beyond-LEO Human Exploration
, Daniel R. Adamo, FISO Colloquium, 2010-10-13, accessed August 22, 2011.
a proposed simpler (single vehicle) first-generation propellant depotPropellant Depots Made Simple
, Bernard Kutter, ''United Launch Alliance'', FISO Colloquium, 2010-11-10, accessed January 10, 2011.
and six important propellant-depot-related technologies for reusable cislunar transportation.Top 10 Technologies for Reusable Cislunar Transportation
, Dallas Bienhoff, ''Boeing'', FISO Colloquium, 2010-12-01, accessed January 10, 2011.

NASA also has plans to mature techniques for enabling and enhancing space flights that use propellant depots in the "CRYOGENIC Propellant STorage And Transfer (CRYOSTAT) Mission". The CRYOSTAT vehicle is expected to be launched to LEO in 2015.

The CRYOSTAT architecture comprises technologies in the following categories:CRYOGENIC Propellant STorage And Transfer (CRYOSTAT) Mission
, Stephan Davis of MSFC, NASA, May 2010
* Storage of Cryogenic Propellants
* Cryogenic Fluid Transfer
* Instrumentation
* Automated Rendezvous and Docking (AR&D)
* Cryogenic Based Propulsion

The "Simple Depot" mission was proposed by NASA in 2011 as a potential first PTSD mission, with launch no earlier than 2015, on an Atlas V 551. ''Simple Depot'' would utilize the "used" (nearly-emptied) Centaur upper stage LH2 tank for long-term storage of LO2 while LH2 will be stored in the Simple Depot LH2 module, which is launched with only ambient-temperature gaseous Helium in it. The SD LH2 tank was to be diameter and long, in volume, and store 5 mT of LH2. "At a useful mixture ratio (MR) of 6:1 this quantity of LH2 can be paired with 25.7 mT of LO2, allowing for 0.7 mT of LH2 to be used for vapor cooling, for a total useful propellant mass of 30 mT. ... the described depot will have a boil-off rate of approaching 0.1 percent per day, consisting entirely of hydrogen."

In September 2010, ULA released a ''Depot-Based Space Transportation Architecture'' concept to propose propellant depots that could be used as way-stations for other spacecraft to stop and refuel—either in low Earth orbit (LEO) for beyond-LEO missions, or at Lagrangian point for interplanetary missions—at the AIAA Space 2010 conference. The concept proposes that waste gaseous hydrogen—an inevitable byproduct of long-term liquid hydrogen storage in the radiative heat environment of space—would be usable as a monopropellant in a solar-thermal propulsion system. The waste hydrogen would be productively utilized for both orbital stationkeeping and attitude control, as well as providing limited propellant and thrust to use for orbital maneuvers to better rendezvous with other spacecraft that would be inbound to receive fuel from the depot.

As part of the Depot-Based Space Transportation Architecture, ULA has proposed the Advanced Common Evolved Stage (ACES) upper stage rocket. ACES hardware is designed from the start as an in-space propellant depot that could be used as way-stations for other rockets to stop and refuel on the way to beyond-LEO or interplanetary missions, and to provide the high-energy technical capacity for the cleanup of space debris.

In August 2011, NASA made a significant contractual commitment to the development of propellant depot technology by funding four aerospace companies to "define demonstration missions that would validate the concept of storing cryogenic propellants in space to reduce the need for large launch vehicles for deep-space exploration."

These study contracts for storing/transferring cryogenic propellants and cryogenic depots were signed with Analytical Mechanics Associates, Boeing, Lockheed Martin and Ball Aerospace. Each company will receive under the contract.

In April 2021, NASA selected the SpaceX Lunar Starship with in-orbit refuelling for their initial lunar human landing system. In 2022, a larger propellant-depot Starship was being planned for Lunar Starship HLS.

Rest of world

The Chinese Space Agency (CNSA) performed its first satellite-to-satellite on-orbit refueling test in June 2016.

Engineering design issues

There are a number of design issues with propellant depots, as well as several tasks that have not, to date, been tested in space for on-orbit servicing missions. The design issues include propellant settling and transfer, propellant usage for attitude control and reboost, the maturity of the refrigeration equipment/cryocoolers, and the power and mass required for reduced or zero boiloff depots with refrigeration.

Propellant settling

Transfer of liquid propellants in microgravity is complicated by the uncertain distribution of liquid and gasses within a tank. Propellant settling at an in-space depot is thus more challenging than in even a slight gravity field. ULA plans to use the DMSP-18 mission to flight-test centrifugal propellant settling as a cryogenic fuel management technique that might be used in future propellant depots. The proposed Simple Depot PTSD mission utilizes several techniques to achieve adequate settling for propellant transfer.

Propellant transfer

In the absence of gravity, propellant transfer is somewhat more difficult, since liquids can float away from the inlet.

As part of the Orbital Express mission in 2007, hydrazine propellant was successfully transferred between two single-purpose designed technology demonstration spacecraft. The Boeing servicing spacecraft ASTRO transferred propellant to the Ball Aerospace serviceable client spacecraft NEXTSat. Since no crew were present on either spacecraft, this was reported as the first autonomous spacecraft-to-spacecraft fluid transfer.

Refilling

After propellant has been transferred to a customer, the depot's tanks will need refilling. Organizing the construction and launch of the tanker rockets bearing the new fuel is the responsibility of the propellant depot's operator. Since space agencies like NASA hope to be purchasers rather than owners, possible operators include the aerospace company that constructed the depot, manufacturers of the rockets, a specialist space depot company, or an oil/chemical company that refines the propellant. By using several tanker rockets the tankers can be smaller than the depot and larger than the spacecraft they are intended to resupply. Short range chemical propulsion tugs belonging to the depot may be used to simplify docking tanker rockets and large vehicles like Mars Transfer Vehicles.

Transfers of propellant between the LEO depot, reachable by rockets from Earth, and the deep space ones such as the Lagrange Points and Phobos depots can be performed using Solar electric propulsion (SEP) tugs.

Two missions are currently under development or proposed to support propellant depot refilling.
* In addition to refueling and servicing geostationary communications satellites with the fuel that is initially launched with the MDA Space Infrastructure Servicing vehicle, the SIS vehicle is being designed to have the ability to orbitally maneuver to rendezvous with a replacement fuel canister after transferring the of fuel in the launch load, enabling further refueling of additional satellites after the initial multi-satellite servicing mission is complete.

* The proposed Simple Depot cryogenic PTSD (Propellant Transfer and Storage Demonstration) mission utilizes "remote berthing arm and docking and fluid transfer ports" both for propellant transfer to other vehicles, as well as for refilling the depot up to the full 30 tonne propellant capacity. It was proposed in 2010, for launch in 2015.

In 1962, S.T. Demetriades proposed a method for refilling by collecting atmospheric gases. Moving in low Earth orbit, at an altitude of around 120 km, Demetriades' proposed depot extracts air from the fringes of the atmosphere, compresses and cools it, and extracts liquid oxygen. The remaining nitrogen is used as propellant for a nuclear-powered magnetohydrodynamic engine, which maintains the orbit, compensating for atmospheric drag. This system was called “PROFAC” ( PROpulsive Fluid ACcumulator). There are, however, safety concerns with placing a nuclear reactor in low Earth orbit.

Demetriades' proposal was further refined by Christopher Jones and others In this proposal, multiple collection vehicles accumulate propellant gases at around 120 km altitude, later transferring them to a higher orbit. However, Jones' proposal does require a network of orbital power-beaming satellites, to avoid placing nuclear reactors in orbit.

Asteroids can also be processed to provide liquid oxygen.

Orbital planes and launch windows

Propellant depots in LEO are of little use for transfer between two low earth orbits when the depot is in a different orbital plane than the target orbit. The delta-v to make the necessary plane change is typically extremely high. On the other hand, depots are typically proposed for exploration missions, where the change over time of the depot's orbit can be chosen to align with the departure vector. This allows one well-aligned departure time minimizing fuel use that requires a very precisely-timed departure. Less efficient departure times from the same depot to the same destination exist before and after the well-aligned opportunity, but more research is required to show whether the efficiency falls off quickly or slowly. By contrast, launching directly in only one launch from the ground without orbital refueling or docking with another craft already on orbit offers daily launch opportunities though it requires larger and more expensive launchers.

The restrictions on departure windows arise because low earth orbits are susceptible to significant perturbations; even over short periods they are subject to nodal regression and, less importantly, precession of perigee. Equatorial depots are more stable but also more difficult to reach.

New approaches have been discovered for LEO to interplanetary orbital transfers where a three-burn orbital transfer is used, which includes a plane change at apogee in a highly-elliptical phasing orbit, in which the incremental delta-v is small—typically less than five percent of the total delta-v—"enabling departures to deep-space destinations akingadvantage of a depot in LEO" and providing frequent departure opportunities.
More specifically, the 3-burn departure strategy has been shown to enable a single LEO depot in an ISS-inclination orbit (51 degrees) to dispatch nine spacecraft to "nine different interplanetary targets here the depot need notperform any phasing maneuvers to align with any of the departure asymptotes ... ncluding enablingextending the economic benefits of dedicated smallsat launch to interplanetary missions."

Specific issues of cryogenic depots

Boil-off mitigation

Boil-off of cryogenic propellants in space may be mitigated by both technological solutions as well as system-level planning and design.
From a technical perspective: for a propellant depot with passive insulation system to effectively store cryogenic fluids, boil-off caused by heating from solar and other sources must be mitigated, eliminated, or used for economic purposes. For non-cryogenic propellants, boil-off is not a significant design problem.

Boil off rate is governed by heat leakage and by the quantity of propellant in the tanks. With partially filled tanks, the percentage loss is higher. Heat leakage depends on surface area, while the original mass of propellant in the tanks depends on volume. So by the cube-square law, the smaller the tank, the faster the liquids will boil off. Some propellant tank designs have achieved a liquid hydrogen boil off rate as low as approximately 0.13% per day (3.8% per month) while the much higher temperature cryogenic fluid of liquid oxygen would boil off much less, about 0.016% per day (0.49% per month).

It is possible to achieve zero boil-off (ZBO) with cryogenic propellant storage using an active thermal control system. Tests conducted at the NASA Lewis Research Center's Supplemental Multilayer Insulation Research Facility (SMIRF) over the summer of 1998 demonstrated that a hybrid thermal control system could eliminate boiloff of cryogenic propellants. The hardware consisted of a pressurized tank insulated with 34 layers of insulation, a condenser, and a Gifford-McMahon (GM) cryocooler that has a cooling capacity of 15 to 17.5 watt (W). Liquid hydrogen was the test fluid. The test tank was installed into a vacuum chamber, simulating space vacuum.

In 2001, a cooperative effort by NASA's Ames Research Center, Glenn Research Center, and Marshall Space Flight Center (MSFC) was implemented to develop zero-boiloff concepts for in-space cryogenic storage. Main program element was a large-scale, zero-boiloff demonstration using the MSFC multipurpose hydrogen test bed (MHTB) - 18.10 m3 L tank (about 1300 kg of ). A commercial cryocooler was interfaced with an existing MHTB spray bar mixer and insulation system in a manner that enabled a balance between incoming and extracted thermal energy.

Another NASA study in June 2003 for conceptual Mars mission showed mass savings over traditional, passive- only cryogenic storage when mission durations are 5 days in LEO for oxygen, 8.5 days for methane and 64 days for hydrogen. Longer missions equate to greater mass savings. Cryogenic xenon saves mass over passive storage almost immediately. When power to run the ZBO is already available, the break-even mission durations are even shorter, e.g. about a month for hydrogen. The larger the tank, the fewer days in LEO when ZBO has reduced mass.

In addition to technical solutions to the challenge of excessive boil-off of cryogenic rocket propellants, system-level solutions have been proposed. From a systems perspective, reductions in the standby time of the LH2 cryogenic storage in order to achieve, effectively, a just in time (JIT) delivery to each customer, matched with the balanced refinery technology to split the long-term storable feedstock—water—into the stoichiometric LOX/ LH2 necessary, is theoretically capable of achieving a system-level solution to boil-off. Such proposals have been suggested as supplementing good technological techniques to reduce boil-off, but would not replace the need for efficient technological storage solutions.Shackleton Energy's cislunar economic development plans
David Livingston interview with James Keravala, ''The Space Show'', December 14, 2012, at 1:08:20-1:09:50, accessed January 3, 2013.

Sun shields

United Launch Alliance (ULA) has proposed a cryogenic depot which would use a conical sun shield to protect the cold propellants from solar and Earth radiation. The open end of the cone allows residual heat to radiate to the cold of deep space, while the closed cone layers attenuates the radiative heat from the Sun and Earth.

Other issues

Other issues are hydrogen embrittlement, a process by which some metals (including iron and titanium) become brittle and fracture following exposure to hydrogen. The resulting leaks makes storing cryogenic propellants in zero gravity conditions difficult.

In-space refueling demonstration projects

In the early 2010s, several in-space refueling projects got under-way. Two private initiatives and a government-sponsored test mission were in some level of development or testing .

Robotic Refueling Mission

The NASA Robotic Refueling Mission was launched in 2011 and successfully completed a series of robotically-actuated propellant transfer experiments on the exposed facility platform of the International Space Station in January 2013.

The set of experiments included a number of propellant valves, nozzles and seals similar to those used on many satellites and a series of four prototype tools that could be attached to the distal end of a Space Station robotic arm. Each tool was a prototype of "devices that could be used by future satellite servicing missions to refuel spacecraft in orbit. RRM is the first in-space refueling demonstration using a platform and fuel valve representative of most existing satellites, which were never designed for refueling. Other satellite servicing demos, such as the U.S. military's Orbital Express mission in 2007, transferred propellant between satellites with specially-built pumps and connections."

MDA in-space refueling demonstration project

, a small-scale refueling demonstration project for reaction control system (RCS) fluids is under development. Canada-based MDA Corporation announced in early 2010 that they were designing a single spacecraft that would refuel other spacecraft in orbit as a satellite-servicing demonstration. "The business model, which is still evolving, could ask customers to pay per kilogram of fuel successfully added to their satellite, with the per-kilogram price being a function of the additional revenue the operator can expect to generate from the spacecraft’s extended operational life."

The plan is that the fuel-depot vehicle would maneuver to an operational communications satellite, dock at the target satellite's apogee-kick motor, remove a small part of the target spacecraft's thermal protection blanket, connect to a fuel-pressure line and deliver the propellant. "MDA officials estimate the docking maneuver would take the communications satellite out of service for about 20 minutes."

, MDA has secured a major customer for the initial demonstration project. Intelsat has agreed to purchase one-half of the propellant payload that the MDA spacecraft would carry into geostationary orbit. Such a purchase would add somewhere between two and four years of additional service life for up to five Intelsat satellites, assuming 200 kg of fuel is delivered to each one.

, the spacecraft could be ready to begin refueling communication satellites by 2015.

, no customers have signed up for an MDA refueling mission.

In 2017, MDA announced that it was restarting its satellite servicing business, with Luxembourg-based satellite owner/operator SES S.A. as its first customer.

Space tug alternatives to direct refueling

Competitive design alternatives to in-space RCS fuel transfer exist. It is possible to bring additional propellant to a space asset, and utilize the propellant for attitude control or orbital velocity change, without ever transferring the propellant to the target space asset.

The ViviSat Mission Extension Vehicle, also under development since the early 2010s, illustrates one alternative approach that would connect to the target satellite similarly to MDA SIS, via the kick motor, but will not transfer fuel. Rather, the Mission Extension Vehicle will use "its own thrusters to supply attitude control for the target."

ViviSat believes their approach is more simple and can operate at lower cost than the MDA propellant transfer approach, while having the technical ability to dock with and service a greater number (90 percent) of the approximately 450 geostationary satellites in orbit.
, no customers have signed up for a ViviSat-enabled mission extension.

In 2015, Lockheed Martin proposed the Jupiter space tug. If built, Jupiter would operate in low Earth orbit shuttling cargo carriers to and from the International Space Station, remaining on orbit indefinitely, and refueling itself from subsequent transport ships carrying later cargo carrier modules.

New Space Involvement

In December 2018, Orbit Fab, a silicon valley startup company founded in early 2018, flew the first of a series of experiments to the ISS in order to test and demonstrate technologies to allow for commercial in space refueling. These first rounds of testing utilise water as a propellant simulant. In June 2021, Orbit Fab flew the first propellant depot, Tanker-001 Tenzing, carrying Hydrogen Peroxide in Sun-synchronous orbit

Gallery

File:Orbital propellant depot 1970 concept (MSFC-9902049).jpg, NASA concept for a propellant depot from 1970
File:Orbital propellant depot - Space transportation system 1971.jpg, Another NASA concept from 1971
File:Depot at GEO.jpg, A 2011 NASA proposal for a Depot at GEO
File:Propellant Depot Evolution.jpg, An evolved propellant depot

See also

* Progress (spacecraft)
* Automated Transfer Vehicle
* Liquid rocket propellants
* Asteroid mining
* Propulsive Fluid Accumulator, satellite that gathers oxygen and other gasses to supply the depot
* Flexible path option of the Review of United States Human Space Flight Plans Committee
* In-situ resource utilization
* Shackleton Energy Company
* Aquarius Launch Vehicle
* Quicklaunch

References

External links

Text

A Backgrounder for On-Orbit Satellite Servicing
March 2011

Presentation of Boeing's proposed LEO Propellant Depot
2007

Evolved Human Space Exploration Architecture Using Commercial Launch/Propellant Depots
Wilhite/Arney/Jones/Chai, October 2012.

Distributed Launch - Enabling Beyond LEO Missions
, United Launch Alliance, September 2015.

Video

Animation of a Boeing depot launch and refuel operation
November 2011 (1 min)

NASA Cryogenic Propellant Depot - Mission Animation
May 2013 (1 min)

Advantages of a depot architecture
Jeff Greason of XCOR Aerospace, Augustine Commission meeting, July 2009 (25 min)

A Settlement Strategy for NASA
Jeff Greason of XCOR Aerospace, ISDC 2011 (42 min)

Cislunar Space, The Next Frontier
Dr. Paul Spudis of the Lunar and Planetary Institute, ISDC 2011 (25 min)

Plan to mine water on the moon using depots
Bill Stone of the Shackleton Energy Company, TED 2011 (7 min)

{{DEFAULTSORT:Propellant Depot
Spaceflight concepts
Rocket propellants
Private spaceflight
Space applications
Fuels infrastructure
Oxygen
Emerging technologies
Industrial gases
Industry in space