Marine propulsion is the mechanism or system used to generate thrust
to move a ship
across water. While paddle
s and sail
s are still used on some smaller boats, most modern ships are propelled by mechanical systems consisting of an electric motor or engine turning a propeller
, or less frequently, in pump-jet
s, an impeller
. Marine engineering
is the discipline concerned with the engineering design process
of marine propulsion system
Manpower, in the form of paddles, and sail were the first forms of marine propulsion. Rowed galley
s, some equipped with sail, also played an important early role. The first advanced mechanical means of marine propulsion was the
marine steam engine
, introduced in the early 19th century. During the 20th century it was replaced by two-stroke
or four-stroke diesel engine
s, outboard motors, and gas turbine engine
s on faster ships. Marine nuclear reactors
, which appeared in the 1950s, produce steam to propel warship
s and icebreaker
s; commercial application, attempted late that decade, failed to catch on. Electric motor
s using electric battery storage have been used for propulsion on submarine
s and electric boat
s and have been proposed for energy-efficient propulsion.
Development in liquefied natural gas
(LNG) fueled engines
are gaining recognition for their low emissions and cost advantages. Stirling engines
, which are quieter, smoother running, propel a number of small submarines
in order to run as quietly as possible. Its design is not used in civilian marine application due to lower total efficiency than internal combustion engines or power turbines.
Until the application of the coal-fired steam engine
to ships in the early 19th century, oars
or the wind
were the principal means of watercraft propulsion. Merchant ships predominantly used sail, but during periods when naval warfare
depended on ships closing to ram
or to fight hand-to-hand, galley
were preferred for their manoeuvrability and speed. The Greek
navies that fought in the Peloponnesian War
s, as did the Romans
at the Battle of Actium
. The development of naval gunnery
from the 16th century onward vaulted broadside weight ahead of manoeuvrability; this led to the dominance of the sail-powered warship over the following three centuries.
In modern times, human propulsion is found mainly on small boats or as auxiliary propulsion on sailboats. Human propulsion includes the push pole, rowing, and pedals.
Propulsion by sail generally consists of a sail hoisted on an erect mast, supported by stays
, and controlled by lines
made of rope
. Sails were the dominant form of commercial propulsion until the late nineteenth century, and continued to be used well into the twentieth century on routes where wind was assured and coal was not available, such as in the South American nitrate trade
. Sails are now generally used for recreation and racing, although innovative applications of kite
's own kite buoy-system have been used on larger modern vessels for fuel savings.
Reciprocating steam engines
The development of piston-engined
steamships was a complex process. Early steamships were fueled by wood, later ones by coal or fuel oil. Early ships used stern or side paddle wheels
, which gave way to screw propeller
The first commercial success accrued to Robert Fulton
's ''North River Steamboat
'' (often called ''Clermont'') in US in 1807, followed in Europe
by the of 1812. Steam propulsion progressed considerably over the rest of the 19th century. Notable developments include the steam surface condenser
, which eliminated the use of sea water in the ship's boilers. This, along with improvements in boiler technology, permitted higher steam pressures, and thus the use of higher efficiency multiple expansion
(compound) engines. As the means of transmitting the engine's power, paddle wheels gave way to more efficient screw propellers.
Multiple expansion steam engines became widespread in the late 19th century. These engines exhausted steam from a high pressure cylinder to a lower pressure cylinder, giving a large increase in efficiency.
Steam turbines were fueled by coal
or, later, fuel oil
or nuclear power
. The marine steam turbine
developed by Sir Charles Algernon Parsons
raised the power-to-weight ratio. He achieved publicity by demonstrating it unofficially in the ''Turbinia
'' at the Spithead Naval Review
in 1897. This facilitated a generation of high-speed liners in the first half of the 20th century, and rendered the reciprocating steam engine obsolete; first in warships, and later in merchant vessels.
In the early 20th century, heavy fuel oil came into more general use and began to replace coal as the fuel of choice in steamships. Its great advantages were convenience, reduced manpower by removal of the need for trimmers
and stokers, and reduced space needed for fuel bunkers.
New liquefied natural gas (LNG) carriers
continue to be built with steam turbines. The natural gas is stored in a liquid state in cryogenic
vessels aboard these ships, and a small amount of "boil-off" gas must be constantly withdrawn in order to maintain the pressure and temperature inside the vessels within operating limits. The boil-off gas provides the fuel for the ship's boilers, which further provide steam for the turbines, the simplest way to deal with the excessive boil-off gas. However, technology to operate internal combustion engine
s (modified marine two-stroke diesel engines) on this gas has improved, and such engines are starting to appear in LNG carriers.
Also, constantly improving tank designs allow greater thermal efficiency, therefore less boil-off naturally occurs. Developments have also been made in the process of re-liquifying boil-off gas, letting it be returned to the cryogenic tanks as a liquid. The financial returns on LNG are potentially greater than the cost of the marine-grade fuel oil burnt in conventional diesel engines, so the re-liquefaction process is starting to be used on diesel engine-propelled LNG carriers. Another factor driving the change from turbines to diesel engines for LNG carriers is the shortage of steam turbine-qualified seagoing engineers. With the lack of turbine powered ships in other shipping sectors, and the rapid rise in size of the worldwide LNG fleet, not enough engineers have been trained to meet the demand. It may be that the days are numbered for marine steam turbine propulsion systems, even though all but sixteen of the orders for new LNG carriers at the end of 2004 were for steam turbine propelled ships.
Nuclear-powered steam turbines
In these vessels, the nuclear reactor
heats water to create steam to drive the turbines. When first developed, very low prices of diesel oil limited nuclear propulsion's commercial attraction. The advantages of its fuel-price security, greater safety and low emissions were unable to overcome the higher initial costs of a nuclear power plant. In 2019, nuclear propulsion is rare except in some Navy
and specialist vessels such as icebreaker
s. In large aircraft carrier
s, the space formerly used for ship's bunkerage is used instead to bunker aviation fuel. In submarine
s, the ability to run submerged at high speed and in relative quiet for long periods holds obvious advantages. A few naval cruiser
s have also employed nuclear power; as of 2006, the only ones remaining in service are the Russia
n . An example of a non-military ship with nuclear marine propulsion
is the with . In an ice-breaker, an advantage is fuel security and safety in demanding arctic conditions. The commercial experiment of the ended before the dramatic fuel price increases of the 1970s. The Savannah also suffered from an inefficient design, being partly for passengers and partly for cargo.
In recent times, there is some renewed interest in commercial nuclear shipping. Fuel oil prices are now much higher. Nuclear-powered cargo ships could lower costs associated with carbon dioxide emissions and travel at higher cruise speeds than conventional diesel powered vessels.
uses electric generators to convert the mechanical energy of a turbine (steam or gas) into electric energy and electric motors to convert it back into mechanical energy to power the driveshafts. An advantage of turbo-electric transmission is that it allows the adaptation of high-speed turbines to slow turning propellers or wheels without a heavy and complex gearbox. It has the advantage of being able to provide electricity for the ship or train's other electrical systems, such as lighting, computers, radar, and communications equipment.
In the second half of the 20th century, rising fuel costs almost led to the demise of the steam turbine. Most new ships since about 1960 have been built with diesel engine
s, both Four or two-Stroke. The last major passenger ship built with steam turbines was ''Fairsky
'', launched in 1984. Similarly, many steam ships were re-engined to improve fuel efficiency
. One high-profile example was the 1968 built ''Queen Elizabeth 2
'' which had her steam turbines replaced with a diesel-electric
propulsion plant in 1986.
Most new-build ships with steam turbines are specialist vessels such as nuclear-powered vessels, and certain merchant vessels (notably Liquefied Natural Gas
(LNG) and coal carriers) where the cargo can be used as bunker fuel
Reciprocating diesel engines
aboard a cargo ship]]
Most modern ships use a reciprocating diesel engine
as their prime mover, due to their operating simplicity, robustness and fuel economy compared to most other prime mover mechanisms. The rotating crankshaft
can be directly coupled to the propeller with slow speed engines, via a reduction gearbox for medium and high speed engines, or via an alternator and electric motor in diesel-electric vessels. The rotation of the crankshaft is connected to the camshaft or a hydraulic pump on an intelligent diesel
The reciprocating marine diesel engine first came into use in 1903 when the diesel electric
was put into service by Branobel
. Diesel engines soon offered greater efficiency than the steam turbine, but for many years had an inferior power-to-space ratio. The advent of turbocharging however hastened their adoption, by permitting greater power densities.
Diesel engines today are broadly classified according to
*Their operating cycle: two-stroke engine
or four-stroke engine
*Their construction: crosshead
, or opposed piston
**Slow speed: any engine with a maximum operating speed up to 300 revolutions per minute
(rpm), although most large two-stroke slow speed diesel engines operate below 120 rpm. Some very long stroke engines have a maximum speed of around 80 rpm. The largest, most powerful engines in the world are slow speed, two stroke, crosshead diesels.
**Medium speed: any engine with a maximum operating speed in the range 300–1000 rpm. Many modern four-stroke medium speed diesel engines have a maximum operating speed of around 500 rpm.
**High speed: any engine with a maximum operating speed above 1000 rpm.
Most modern larger merchant ships use either slow speed, two stroke, crosshead engines, or medium speed, four stroke, trunk engines. Some smaller vessels may use high speed diesel engines.
The size of the different types of engines is an important factor in selecting what will be installed in a new ship. Slow speed two-stroke engines are much taller, but the footprint required is smaller than that needed for equivalently rated four-stroke medium speed diesel engines. As space above the waterline is at a premium in passenger ships and ferries (especially ones with a car deck), these ships tend to use multiple medium speed engines resulting in a longer, lower engine room than that needed for two-stroke diesel engines. Multiple engine installations also give redundancy in the event of mechanical failure of one or more engines, and the potential for greater efficiency over a wider range of operating conditions.
As modern ships' propellers are at their most efficient at the operating speed of most slow speed diesel engines, ships with these engines do not generally need gearboxes. Usually such propulsion systems consist of either one or two propeller shafts each with its own direct drive engine. Ships propelled by medium or high speed diesel engines may have one or two (sometimes more) propellers, commonly with one or more engines driving each propeller shaft through a gearbox. Where more than one engine is geared to a single shaft, each engine will most likely drive through a clutch, allowing engines not being used to be disconnected from the gearbox while others keep running. This arrangement lets maintenance be carried out while under way, even far from port.
Shipping companies are required to comply with the International Maritime Organization
(IMO) and the International Convention for the Prevention of Pollution from Ships
emissions rules. Dual fuel engines are fueled by either marine grade diesel, heavy fuel oil, or liquefied natural gas (LNG). A Marine LNG Engine
has multiple fuel options, allowing vessels to transit without relying on one type of fuel. Studies show that LNG is the most efficient of fuels, although limited access to LNG fueling stations limits the production of such engines. Vessels providing services in the LNG industry have been retrofitted with dual-fuel engines, and have been proved to be extremely effective. Benefits of dual-fuel engines include fuel and operational flexibility, high efficiency, low emissions, and operational cost advantages.
Liquefied natural gas engines offer the marine transportation industry with an environmentally friendly alternative to provide power to vessels. In 2010, STX Finland and Viking Line signed an agreement to begin construction on what would be the largest environmentally friendly cruise ferry. Construction of NB 1376 will be completed in 2013. According to Viking Line, vessel NB 1376 will primarily be fueled by liquefied natural gas. Vessel NB 1376 nitrogen oxide emissions will be almost zero, and sulphur oxide emissions will be at least 80% below the International Maritime Organization’s (IMO) standards.
Company profits from tax cuts and operational cost advantages has led to the gradual growth of LNG fuel use in engines.
Many warships built since the 1960s have used gas turbine
s for propulsion, as have a few passenger ships, like the jetfoil
. Gas turbines are commonly used in combination with other types of engine. Most recently, has had gas turbines installed in addition to diesel engines
. Because of their poor thermal efficiency at low power (cruising) output, it is common for ships using them to have diesel engines for cruising, with gas turbines reserved for when higher speeds are needed. However, in the case of passenger ships the main reason for installing gas turbines has been to allow a reduction of emissions in sensitive environmental areas or while in port. Some warships, and a few modern cruise ships have also used steam turbines to improve the efficiency of their gas turbines in a combined cycle
, where waste heat
from a gas turbine exhaust is utilized to boil water and create steam for driving a steam turbine. In such combined cycles, thermal efficiency can be the same or slightly greater than that of diesel engines alone; however, the grade of fuel needed for these gas turbines is far more costly than that needed for the diesel engines, so the running costs are still higher.
Since the late 1980s, Swedish shipbuilder Kockums
has built a number of successful Stirling engine powered submarines.
The submarines store compressed oxygen to allow more efficient and cleaner external fuel combustion when submerged, providing heat for the Stirling engine's operation. The engines are currently used on submarines of the and classes. and the Japanese submarine. These are the first submarines to feature Stirling air-independent propulsion
(AIP), which extends the underwater endurance from a few days to several weeks.
The heat sink of a Stirling engine is typically the ambient air temperature. In the case of medium to high power Stirling engines, a radiator
is generally required to transfer the heat from the engine to the ambient air. Stirling marine engines have the advantage of using the ambient temperature water. Placing the cooling radiator section in seawater rather than ambient air allows for the radiator to be smaller. The engine's cooling water may be used directly or indirectly for heating and cooling purposes of the ship. The Stirling engine has potential for surface-ship propulsion, as the engine's larger physical size is less of a concern.
Battery-electric propulsion first appeared in the latter part of the 19th century, powering small lake boats. These relied entirely on lead-acid batteries
for electric current to power their propellers. Elco
(the Electric Launch Company) evolved into the industry leader, later expanding into other forms of vessel, including the iconic World War II PT boat
In the early part of the 20th century electric propulsion was adapted to use in submarine
s. As underwater propulsion driven exclusively by heavy batteries was both slow and of limited range and timespan, rechargeable battery banks were developed. Submarines were primarily powered by combined diesel-electric
systems on the surface, which were much faster and allowed for dramatically expanded range, charging their battery systems as necessary for still limited subsurface action and duration. The experimental ''Holland V
'' submarine led to the adoption of this system by the U.S. Navy
, followed by the British Royal Navy
To expand the range and duration of the submarine during World War II the German Kriegsmarine
developed a snorkel
system, which allowed the diesel-electric system to be utilized while the submarine was all but completely submerged. Finally, in 1952, the USS ''Nautilus''
was launched, the world's first nuclear powered submarine, which eliminated the restrictions of both diesel fuel and limited duration battery propulsion.
Several short-range ships are built as (or converted to) pure electric vessels
. This includes some powered by batteries which are recharged from shore, and some shore-power
ed by electrical cables
, either overhead
On November 12, 2017 Guangzhou Shipyard International
(GSI) launched what may be the world's first all-electric, battery-powered inland coal carrier. The 2,000 dwt vessel will carry bulk cargo for up to 40 nautical miles per charge. The ship carries lithium ion batteries
rated at 2,400 kilowatt-hours, about the same amount as 30 Tesla Model S
Numerous types of propulsion have been developed over time. These include:
Marine propellers are also known as "screws". There are many variations of marine screw systems, including twin, contra-rotating, controllable-pitch, and nozzle-style screws. While smaller vessels tend to have a single screw, even very large ships such as tankers, container ships and bulk carriers may have single screws for reasons of fuel efficiency. Other vessels may have twin, triple or quadruple screws. Power is transmitted from the engine to the screw by way of a propeller shaft, which may be connected to a gearbox.
The paddle wheel is a large wheel, generally built of a steel frame
work, upon the outer edge of which are fitted numerous paddle blades (called ''floats'' or ''buckets''). The bottom quarter or so of the wheel travels underwater. Rotation of the paddle wheel produces thrust
, forward or backward as required. More advanced paddle wheel designs have featured ''feathering'' methods that keep each paddle blade oriented closer to vertical while it is in the water; this increases efficiency. The upper part of a paddle wheel is normally enclosed in a paddlebox to minimise splashing.
Paddle wheels have been superseded by screws, which are a much more efficient form of propulsion. Nevertheless, paddle wheels have two advantages over screws, making them suitable for vessels in shallow rivers and constrained waters: first, they are less likely to be clogged by obstacles and debris; and secondly, when contra-rotating, they allow the vessel to spin around its own vertical axis. Some vessels had a single screw in addition to two paddle wheels, to gain the advantages of both types of propulsion.
A pump-jet, hydrojet, water jet, or jet drive uses a ducted propeller
), centrifugal pump
, or mixed flow pump to create a jet of water for propulsion.
These incorporate an intake for source water and a nozzle to direct its flow out, generating momentum, and in most cases, employing thrust vectoring to steer the craft.
Pump-jets are found on personal watercraft
, shallow-draft river boats, and torpedoes.
The purpose of sail
s is to use wind energy
to propel the vessel
right|thumb|100px|Voith Schneider Propeller
A Voith Schneider Propeller
(VSP) is a practical cyclorotor
that provides instant thrust in any direction. There is no need to turn a propulsor. Most ships with VSPs do not need or have a rudder. VSPs are often used in tugboats, drilling vessels, and other watercraft that require unusually good maneuverability. First deployed in the 1930s, Voith-Schneider drives are both reliable and available in large sizes.
An early uncommon means of boat propulsion was the water caterpillar. This moved a series of paddles on chains along the bottom of the boat to propel it over the water and preceded the development of tracked vehicle
The first water caterpillar was developed by Joseph-Philibert Desblanc
in 1782 and propelled by a steam engine. In the United States the first water caterpillar was patented in 1839 by William Leavenworth of New York.
convert buoyancy to thrust, using wings, or more recently hull shape (SeaExplorer Glider). Buoyancy is made alternatively negative and positive, generating tooth-saw profiles.