Macaulay's method

Macaulay’s method (the double integration method) is a technique used in structural analysis to determine the deflection of Euler-Bernoulli beams. Use of Macaulay’s technique is very convenient for cases of discontinuous and/or discrete loading. Typically partial uniformly distributed loads (u.d.l.) and uniformly varying loads (u.v.l.) over the span and a number of concentrated loads are conveniently handled using this technique.

The first English language description of the method was by Macaulay.W. H. Macaulay, "A note on the deflection of beams", Messenger of Mathematics, 48 (1919), 129.
/ref> The actual approach appears to have been developed by Clebsch in 1862.J. T. Weissenburger, ‘Integration of discontinuous expressions arising in beam theory’, AIAA
Journal, 2(1) (1964), 106–108. Macaulay's method has been generalized for Euler-Bernoulli beams with axial compression, W. H. Wittrick, "A generalization of Macaulay’s method with applications in structural mechanics", AIAA Journal, 3(2) (1965), 326–330. to Timoshenko beams,A. Yavari, S. Sarkani and J. N. Reddy, ‘On nonuniform Euler–Bernoulli and Timoshenko beams with jump discontinuities: application of distribution theory’, International Journal of Solids and Structures, 38(46–7) (2001), 8389–8406. to elastic foundations,A. Yavari, S. Sarkani and J. N. Reddy, ‘Generalised solutions of beams with jump discontinuities
on elastic foundations’, Archive of Applied Mechanics, 71(9) (2001), 625–639. and to problems in which the bending and shear stiffness changes discontinuously in a beam.Stephen, N. G., (2002), "Macaulay's method for a Timoshenko beam", Int. J. Mech. Engg. Education, 35(4), pp. 286-292.

Method

The starting point is the relation from Euler-Bernoulli beam theory
:$\pm EI\dfrac = M$
Where $w$ is the deflection and $M$ is the bending moment.
This equationThe sign on the left hand side of the equation depends on the convention that is used. For the rest of this article we will assume that the sign convention is such that a positive sign is appropriate. is simpler than the fourth-order beam equation and can be integrated twice to find $w$ if the value of $M$ as a function of $x$ is known. For general loadings, $M$ can be expressed in the form
:$M = M_1(x) + P_1\langle x - a_1\rangle + P_2\langle x - a_2\rangle + P_3\langle x - a_3\rangle + \dots$
where the quantities $P_i\langle x - a_i\rangle$ represent the bending moments due to point loads and the quantity $\langle x - a_i\rangle$ is a Macaulay bracket defined as
:$\langle x - a_i\rangle = \begin 0 & \mathrm~ x < a_i \\ x - a_i & \mathrm~ x > a_i \end$
Ordinarily, when integrating $P(x-a)$ we get
:
\int P(x-a)~dx = P\left cfrac - ax\right+ C

However, when integrating expressions containing Macaulay brackets, we have
:$\int P\langle x-a \rangle~dx = P\cfrac + C_m$
with the difference between the two expressions being contained in the constant $C_m$. Using these integration rules makes the calculation of the deflection of Euler-Bernoulli beams simple in situations where there are multiple point loads and point moments. The Macaulay method predates more sophisticated concepts such as Dirac delta functions and step functions but achieves the same outcomes for beam problems.

Example: Simply supported beam with point load

An illustration of the Macaulay method considers a simply supported beam with a single eccentric concentrated load as shown in the adjacent figure. The first step is to find $M$. The reactions at the supports A and C are determined from the balance of forces and moments as
:$R_A + R_C = P,~~ L R_C = P a$
Therefore, $R_A = Pb/L$ and the bending moment at a point D between A and B ($0 < x < a$) is given by
:$M = R_A x = Pbx/L$
Using the moment-curvature relation and the Euler-Bernoulli expression for the bending moment, we have
:$EI\dfrac = \dfrac$
Integrating the above equation we get, for $0 < x < a$,
:$\begin EI\dfrac &= \dfrac +C_1 & &\quad\mathrm\\ EI w &= \dfrac + C_1 x + C_2 & &\quad\mathrm \end$
At $x=a_$
:$\begin EI\dfrac(a_) &= \dfrac +C_1 & &\quad\mathrm \\ EI w(a_) &= \dfrac + C_1 a + C_2 & &\quad\mathrm \end$
For a point D in the region BC ($a < x < L$), the bending moment is
:$M = R_A x - P(x-a) = Pbx/L - P(x-a)$
In Macaulay's approach we use the Macaulay bracket form of the above expression to represent the fact that a point load has been applied at location B, i.e.,
:$M = \frac - P\langle x-a \rangle$

Therefore, the Euler-Bernoulli beam equation for this region has the form
:$EI\dfrac = \dfrac - P\langle x-a \rangle$
Integrating the above equation, we get for $a < x < L$
:$\begin EI\dfrac &= \dfrac - P\cfrac + D_1 & &\quad\mathrm\\ EI w &= \dfrac - P\cfrac + D_1 x + D_2 & &\quad\mathrm \end$
At $x=a_$
:$\begin EI\dfrac(a_) &= \dfrac + D_1 & &\quad\mathrm\\ EI w(a_) &= \dfrac + D_1 a + D_2 & &\quad\mathrm \end$

Comparing equations (iii) & (vii) and (iv) & (viii) we notice that due to continuity at point B, $C_1 = D_1$ and $C_2 = D_2$. The above observation implies that for the two regions considered, though the equation for bending moment and hence for the curvature are different, the constants of integration got during successive integration of the equation for curvature for the two regions are the same.

The above argument holds true for any number/type of discontinuities in the equations for curvature, provided that in each case the equation retains the term for the subsequent region in the form $\langle x-a\rangle ^n, \langle x-b\rangle ^n, \langle x-c\rangle ^n$ etc.
It should be remembered that for any x, giving the quantities within the brackets, as in the above case, -ve should be neglected, and the calculations should be made considering only the quantities which give +ve sign for the terms within the brackets.

Reverting to the problem, we have
:$EI\dfrac = \dfrac - P\langle x-a \rangle$
It is obvious that the first term only is to be considered for $x < a$ and both the terms for $x > a$ and the solution is
:
\begin
EI\dfrac &= \left dfrac + C_1\right- \cfrac \\
EI w &= \left dfrac + C_1 x + C_2\right- \cfrac
\end

Note that the constants are placed immediately after the first term to indicate that they go with the first term when $x < a$ and with both the terms when $x > a$. The Macaulay brackets help as a reminder that the quantity on the right is zero when considering points with $x < a$.

Boundary Conditions

As $w = 0$ at $x = 0$, $C2 = 0$. Also, as $w = 0$ at $x = L$,
:
\left dfrac + C_1 L \right- \cfrac = 0

or,
:$C_1 = -\cfrac(L^2-b^2) ~.$
Hence,
:
\begin
EI\dfrac &= \left dfrac -\cfrac(L^2-b^2)\right- \cfrac \\
EI w &= \left dfrac -\cfrac(L^2-b^2)\right- \cfrac
\end

Maximum deflection

For $w$ to be maximum, $dw/dx = 0$. Assuming that this happens for $x < a$ we have
:$\dfrac -\cfrac(L^2-b^2) = 0$
or
:$x = \pm \cfrac$
Clearly $x < 0$ cannot be a solution. Therefore, the maximum deflection is given by
:
EI w_ = \cfrac\left dfrac\right-\cfrac

or,
:$w_ = -\dfrac~.$

Deflection at load application point

At $x = a$, i.e., at point B, the deflection is
:$EI w_B = \dfrac -\cfrac(L^2-b^2) = \frac(a^2+b^2-L^2)$
or
:$w_B = -\cfrac$

Deflection at midpoint

It is instructive to examine the ratio of $w_/w(L/2)$. At $x = L/2$
:
EI w(L/2) = \dfrac -\cfrac(L^2-b^2) = -\frac\left frac -b^2\right
Therefore,
:$\frac = \frac = \frac = \frac$
where $k = B/L$ and for $a < b; 0 < k < 0.5$. Even when the load is as near as 0.05L from the support, the error in estimating the deflection is only 2.6%. Hence in most of the cases the estimation of maximum deflection may be made fairly accurately with reasonable margin of error by working out deflection at the centre.

Special case of symmetrically applied load

When $a = b = L/2$, for $w$ to be maximum
:$x = \cfrac = \frac$
and the maximum deflection is
:$w_ = -\dfrac = -\frac = w(L/2)~.$

References

See also

* Beam theory
* Bending
* Bending moment
* Singularity function
* Shear and moment diagram
* Timoshenko beam theory

{{Structural engineering topics

Structural analysis