Line-level

Line level is the specified strength of an audio signal used to transmit analog audio between components such as CD and DVD players, television sets, audio amplifiers, and mixing consoles.

Line level sits between other levels of audio signals. There are weaker signals such as those from microphones (microphone level or mic level) and instrument pickups (instrument level), and stronger signals, such as those used to drive headphones and loudspeakers (speaker level). The "strength" of these various signals does not necessarily refer to the output voltage of the source device; it also depends on its output impedance and output power capability.

Consumer electronic devices concerned with audio (for example sound cards) often have a connector labeled ''line in'' and/or ''line out''. ''Line out'' provides an audio signal output and ''line in'' receives a signal input. The line in/out connections on consumer-oriented audio equipment are typically unbalanced, with a (0.14 inch, but commonly called "eighth inch") 3-conductor TRS minijack connector providing ground, left channel, and right channel, or stereo RCA jacks. Professional equipment commonly uses balanced connections on (1/4 inch) TRS phone jacks or XLR connectors. Professional equipment may also use unbalanced connections with (1/4 inch) TS phone jacks.

Nominal levels

A line level describes a line's nominal signal level as a ratio, expressed in decibels, against a standard reference voltage. The nominal level and the reference voltage against which it is expressed depend on the line level being used. While the nominal levels themselves vary, only two reference voltages are common: for consumer applications, and for professional applications.

The decibel volt reference voltage is . The decibel unloaded reference voltage, , is the AC voltage required to produce of power across a impedance (approximately ). This awkward unit is a holdover from the early telephone standards, which used 600 Ω sources and loads, and measured dissipated power in decibel-milliwatts ( dBm). Modern audio equipment does not use 600 Ω matched loads, hence ''dBm unloaded'' (''dBu'').

The most common nominal level for professional equipment is (by convention, decibel values are written with an explicit sign symbol). For consumer equipment, a convention exists of , originally intended to reduce manufacturing costs. However, consumer equipment may not necessarily follow that convention. For example, a standard CD-player output voltage has emerged of around 2 V_RMS, equivalent to +6 dBV. Such higher output levels allow the CD player to bypass a preamp stage.

Expressed in absolute terms, a signal at is equivalent to a sine wave signal with a peak amplitude (V_PK) of approximately , or any general signal at root mean square (V_RMS). A signal at is equivalent to a sine wave signal with a peak amplitude of approximately , or any general signal at approximately 1.228 V_RMS.

Peak-to-peak (sometimes abbreviated as ''p-p'') amplitude (V_PP) refers to the total voltage swing of a signal, which is double the peak amplitude of the signal. For instance, a signal with a peak amplitude of has a of .

The line level signal is an alternating current signal without a DC offset, meaning that its voltage varies with respect to signal ground from the peak amplitude (for example ) to the equivalent negative voltage ().

Impedances

A line driver is typically used to drive line-level analog signal outputs. As cables between line output and line input are generally extremely short compared to the audio signal wavelength in the cable, transmission line effects can be disregarded and impedance matching need not be used. Instead, line level circuits use the impedance bridging principle, in which a low impedance output drives a high impedance input. A typical line out connection has an output impedance from 100 to , with lower values being more common in newer equipment. Line inputs present a much higher impedance, typically or more.

The two impedances form a voltage divider with a shunt element that is large relative to the size of the series element, which ensures that little of the signal is shunted to ground and that current requirements are minimized. Most of the voltage asserted by the output appears across the input impedance and almost none of the voltage is dropped across the output. The line input acts similarly to a high impedance voltmeter or oscilloscope input, measuring the voltage asserted by the output while drawing minimal current (and hence minimal power) from the source. The high impedance of the line in the circuit does not load down the output of the source device.

These are voltage signals (as opposed to current signals) and it is the signal information (voltage) that is desired, not power to drive a transducer, such as a speaker or antenna. The actual information that is exchanged between the devices is the variance in voltage; it is this alternating voltage signal that conveys the information, making the current irrelevant.

Line out

            Line-out symbol. PC Guide color lime green.

Line outputs usually present a source impedance of 100 to 600 ohms. The voltage can reach 2 volts peak-to-peak with levels referenced to −10 dBV (300 mV) at . The frequency response of most modern equipment is advertised as at least 20 Hz to 20 kHz, which corresponds to the conventional range of human hearing. Line outputs are intended to drive a load impedance of
10,000 ohms; with only a few volts, this requires only minimal current.

Connecting other devices

Connecting a low-impedance load such as a loudspeaker (usually ) to a line out will essentially short circuit the output circuit. Such loads are around 1/1000 the impedance a line out is designed to drive, so the line out is usually not designed to source the current that would be drawn by a 4 to 8 ohm load at normal line out signal voltages. The result will be very weak sound from the speaker and possibly a damaged line out circuit.

Headphone outputs and line outputs are sometimes confused.
Different make and model headphones have widely varying impedances, from as little as to a few hundred ohms; the lowest of these will have results similar to a speaker, while the highest may work acceptably if the line out impedance is low enough and the headphones are sensitive enough.

Conversely, a headphone output generally has a source impedance of only a few ohms (to provide a bridging connection with 32 ohm headphones) and will easily drive a line input.

For similar reasons, "wye"-cables (or "Y-splitters") should not be used to combine two line out signals into a single line in.
Each line output would be driving the other line output as well as the intended input,
again resulting in a much heavier load than designed for. This will result in signal loss and possibly even damage.
An active mixer, using for example op-amps,
should be used instead. A large resistor in series with each output can be used to safely mix them together, but must be appropriately designed for the load impedance and cable length.

Line in

            Line-in symbol. PC Guide color light blue.

It is intended by designers that the line out of one device be connected to the line input of another. Line inputs are designed to accept voltage levels in the range provided by line outputs.
Impedances, on the other hand, are deliberately not matched from output to input.
The impedance of a line input is typically around .
When driven by a line output's usual low impedance of 100 to 600 ohms, this forms a bridging connection in which most of the voltage generated by the source (the output) is dropped across the load (the input), and minimal current flows due to the load's relatively high impedance.

Although line inputs have a high impedance compared to that of line outputs,
they should not be confused with so-called "Hi-Z" inputs (Z being the symbol for impedance) which have an impedance of to over . These "Hi-Z" or "instrument" inputs generally have higher gain than a line input.
They are designed to be used with, for example, electric guitar pickups and " direct input" boxes.
Some of these sources can provide only minimal voltage and current and the high impedance input is designed to not load them excessively.

Line level in traditional signal paths

Acoustic sounds (such as voices or musical instruments) are often recorded with transducers (microphones and pickups) that produce weak electrical signals. These signals must be amplified to line level, where they are more easily manipulated by other devices such as mixing consoles and tape recorders. Such amplification is performed by a device known as a preamplifier or "preamp",
which boosts the signal to line level.
After manipulation at line level, signals are then typically sent to a power amplifier, where they are amplified to levels that can drive headphones or loudspeakers. These convert the signals back into sounds that can be heard through the air.

Most phonograph cartridges also have a low output level and require a preamp; typically, a home stereo integrated amplifier or receiver will have a special phono input. This input passes the signal through a phono preamp, which applies RIAA equalization to the signal as well as boosting it to line level.

See also

*Nominal level
*Alignment level
*Microphone
*Preamplifier
*Amplifier
*Soundcard

References

External links

*
Conversion of dBu to volts, dBV to volts, and volts to dBu, and dBV

{{DEFAULTSORT:Line Level
Electronic engineering
Audio engineering
Sound
Consumer electronics
Signal cables