Heave to

In sailing, heaving to (to heave to and to be hove to) is a way of slowing a sailing vessel's forward progress, as well as fixing the helm and sail positions so that the vessel does not have to be steered. It is commonly used for a "break"; this may be to wait for the tide before proceeding, or to wait out a strong or contrary wind. For a solo or shorthanded sailor it can provide time to go below deck, to attend to issues elsewhere on the boat or to take a meal break.www.sailingusa.info/points_of_sail.htm
It is also used as a storm tactic.

The term is also used in the context of vessels under power and refers to bringing the vessel to a complete stop. For example, in waters over which the United States has jurisdiction the Coast Guard may, unde
14 U.S.C. §522
demand that a boat "heave to" in order to enforce federal laws.

Hove to

A sailing vessel is hove to when it is at or nearly at rest because the driving action from one or more sails is approximately balanced by the drive from the other(s). This always involves "backing" one or more sails, so that the wind is pressing against the forward side of the cloth, rather than the aft side as it normally would for the sail to drive the vessel forwards. On large square rigged, multi-masted vessels the procedures can be quite complex and varied, but on a modern two-sailed sloop, there is only the jib and the mainsail. A cutter may have more than one headsail, and a ketch, yawl or schooner may have more than one sail on a boom. In what follows, the jibs and boomed sails on such craft can either be treated as one of each, or lowered for the purposes of reduced windage, heel or complexity when heaving to for any length of time.

When a sloop is hove to, the jib is backed. This means that its windward sheet is tight holding the sail to windward. The mainsail sheet is often eased, or the mainsail reefed, to reduce forward movement, or "fore-reaching". The rudder is placed so that, should the boat make any forward movement, it will be turned ''into'' the wind, so as to prevent forward momentum building up. In a centerboard boat the centerboard will be partially raised and the tiller held down hard.

Heaving to

For a sloop sailing along normally, either of two maneuvers will render the sailboat to be hove to.

First, the jib can be literally ''heaved'' to windward, using the windward sheet and releasing the other. Then the rudder would be put across so as to turn gently towards the wind. Without the drive of the jib, and allowing time for momentum to die down, the sailboat will be unable to tack and will stop hove to. This method may be preferable when broad reaching or running before a strong wind in a heavy sea and the prospect of tacking through the wind in order to heave to may not appeal. Bearing away from the wind so that the headsail is blanketed by the mainsail can make it easier to haul in the windward sheet.

Alternatively, the vessel can simply be turned normally to tack through the wind, ''without'' freeing the jibsheet. The mainsail should self-tack onto the other side, but the jib is held aback. Finally the rudder is put the other way, as if trying to tack back again. Without the drive of the jib, she cannot do this and will stop hove to. This method is fast to implement and is recommended by sail training bodies such as the RYA as a "quick stop" reaction to a man overboard emergency, for sailing boats that have an engine available for further maneuvers to approach and pick up the casualty.

Finally, in either case, the tiller or wheel should be lashed so that the rudder cannot move again, and the mainsheet adjusted so that the boat lies with the wind ahead of the beam with minimal speed forward. Usually this involves easing the sheet slightly compared to a closehauled position, but depending on the relative sizes of the sails, the shape and configuration of the keel and rudder and the state of the wind and sea, each skipper will have to experiment. After this the boat can be left indefinitely, only keeping a lookout for other approaching vessels.

When hove to, the boat will heel, there will be some drift to leeward and some tendency to forereach, so adequate seaway must be allowed for. In rough weather, this leeway can actually leave a "slick" effect to windward, in which the waves are smaller than elsewhere. This can make a rest or meal break a little more comfortable at times.

To come out from the hove-to position and get under way again, the tiller or wheel is unlashed and the windward jibsheet is released, hauling in the normal leeward one. Bearing off the wind using the rudder will get the boat moving and then she can be maneuvered onto any desired course. It is important when choosing the tack, heaving to, and remaining hove to, in a confined space that adequate room is allowed for these maneuvers.

Heaving to as a storm tactic

Heaving to has been used by a number of yachts to survive storm conditions (winds greater than Force 10, 48–55 knots, 89–102km/h, 55–63mph). During the June 1994 Queen's Birthday Storm, all yachts that hove to survived the storm. This included ''Sabre'', a 10.4m (34ft) steel cutter with two persons on board, which hove to in wind speeds averaging 80 knots for 6 hours with virtually no damage.

During the ill-fated 1979 Fastnet race, of 300 yachts, 158 chose to adopt storm tactics; 86 " lay ahull", whereby the yacht adopts a "beam on" attitude to the wind and waves; 46 ran before the wind under bare poles or trailing warps/sea anchors, and 26 hove to. 100 yachts suffered knock downs; 77 rolled (that is turtled) at least once. Not one of the hove to yachts were capsized (knocked down or turtled) or suffered any serious damage. The "heave to" maneuver is described in the story of the first Golden Globe yacht race of 1968.

See also

*
*
*
*
*
*

References

{{Sailing manoeuvres
Sailing manoeuvres