Gain–bandwidth product
   HOME

TheInfoList



OR:

The gain–bandwidth product (designated as GBWP, GBW, GBP, or GB) for an
amplifier An amplifier, electronic amplifier or (informally) amp is an electronic device that can increase the magnitude of a signal (a time-varying voltage or current). It may increase the power significantly, or its main effect may be to boost t ...
is the product of the amplifier's
bandwidth Bandwidth commonly refers to: * Bandwidth (signal processing) or ''analog bandwidth'', ''frequency bandwidth'', or ''radio bandwidth'', a measure of the width of a frequency range * Bandwidth (computing), the rate of data transfer, bit rate or thr ...
and the gain at which the bandwidth is measured. For devices such as
operational amplifier An operational amplifier (often op amp or opamp) is a DC-coupled high-gain electronic voltage amplifier with a differential input and, usually, a single-ended output. In this configuration, an op amp produces an output potential (relative to c ...
s that are designed to have a simple one-pole
frequency Frequency is the number of occurrences of a repeating event per unit of time. It is also occasionally referred to as ''temporal frequency'' for clarity, and is distinct from ''angular frequency''. Frequency is measured in hertz (Hz) which is eq ...
response, the gain–bandwidth product is nearly independent of the gain at which it is measured; in such devices the gain–bandwidth product will also be equal to the unity-gain bandwidth of the amplifier (the bandwidth within which the amplifier gain is at least 1). For an amplifier in which negative feedback reduces the gain to below the
open-loop gain The open-loop gain of an electronic amplifier is the gain obtained when no overall feedback is used in the circuit. The open-loop gain of many electronic amplifiers is exceedingly high (by design) – an ''ideal'' operational amplifier (op-amp) ...
, the gain–bandwidth product of the closed-loop amplifier will be approximately equal to that of the open-loop amplifier. According to S. Srinivasan, "The parameter characterizing the frequency dependence of the operational amplifier gain is the finite gain–bandwidth product (GB)."


Relevance to design

This quantity is commonly specified for
operational amplifier An operational amplifier (often op amp or opamp) is a DC-coupled high-gain electronic voltage amplifier with a differential input and, usually, a single-ended output. In this configuration, an op amp produces an output potential (relative to c ...
s, and allows
circuit design The process of circuit design can cover systems ranging from complex electronic systems down to the individual transistors within an integrated circuit. One person can often do the design process without needing a planned or structured design ...
ers to determine the maximum gain that can be extracted from the device for a given frequency (or bandwidth) and vice versa. When adding LC circuits to the input and output of an amplifier the gain rises and the bandwidth decreases, but the product is generally bounded by the gain–bandwidth product.


Examples

If the GBWP of an operational amplifier is 1 MHz, it means that the gain of the device falls to unity at 1 MHz. Hence, when the device is wired for unity gain, it will work up to 1 MHz (GBWP = gain × bandwidth, therefore if BW = 1 MHz, then gain = 1) without excessively distorting the signal. The same device when wired for a gain of 10 will work only up to 100 kHz, in accordance with the GBW product formula. Further, if the maximum frequency of operation is 1 Hz, then the maximum gain that can be extracted from the device is 1. We can also analytically show that for \omega \gg \omega_c GBWP is constant. Let A_1(\omega) be a first-order transfer function given by: A_1(\omega)= \frac We will show that: \mathit_ = (\omega )\cdot\omega \approx \mathrm Proof: We will expand A_1 using
Taylor series In mathematics, the Taylor series or Taylor expansion of a function is an infinite sum of terms that are expressed in terms of the function's derivatives at a single point. For most common functions, the function and the sum of its Taylor ser ...
and retain the constant and first term, to obtain: \mathit = (\omega )\cdot\omega = \frac\cdot\omega \simeq \frac = \cdot \left(1- \frac \right) = \mathrm Example for \omega = 5\cdot \omega_c \mathit\ = \frac\cdot5 = \frac\cdot = 0.98\cdot\cdot Note that the error in this case is only about 2%, for the constant term, and using the second term, \left(1- \frac \right) , the error drops to .06%.


Transistors

For
transistor upright=1.4, gate (G), body (B), source (S) and drain (D) terminals. The gate is separated from the body by an insulating layer (pink). A transistor is a semiconductor device used to Electronic amplifier, amplify or electronic switch, switch ...
s, the current-gain–bandwidth product is known as the or ''transition frequency''. It is calculated from the low-frequency (a few kilohertz) current gain under specified test conditions, and the ''cutoff frequency'' at which the current gain drops by 3 decibels (70% amplitude); the product of these two values can be thought of as the frequency at which the current gain would drop to 1, and the transistor current gain between the cutoff and transition frequency can be estimated by dividing by the frequency. Usually, transistors must be used at frequencies well below to be useful as amplifiers and oscillators.Martin Hartley Jones ''A practical introduction to electronic circuits'', Cambridge University Press, 1995 page 148 In a bipolar junction transistor, frequency response declines owing to the internal capacitance of the junctions. The transition frequency varies with collector current, reaching a maximum for some value and declining for greater or lesser collector current.


References


External links


"Op-amp gain-bandwidth-product"
masteringelectronicsdesign.com {{DEFAULTSORT:Gain-bandwidth product Electronic amplifiers