Ferrari flat-12 engine on:
[Wikipedia]
[Google]
[Amazon]
The Ferrari flat-12 engine family is a series of Flat-twelve engine, flat-12 Overhead camshaft, DOHC petrol engines produced by Ferrari from 1964 to 1996. The first racing Ferrari flat-12, the Mauro Forghieri-designed ''Tipo 207'', was introduced in the Ferrari 158, Ferrari 1512 F1 car in 1964. Later flat-12 racing engines were used in Ferrari Formula One and sports racing cars from 1968 until 1980, including the Ferrari 212 E Montagna, 212 E Montagna, Ferrari 312B, 312 B series, Ferrari 312 PB, 312 PB and Ferrari 312T, 312 T series. The roadgoing flat-12 engines were introduced with the Ferrari Berlinetta Boxer, 365 GT4 BB and were produced in various versions until the end of Ferrari Testarossa, F512M production in 1996.
Ferrari flat-12 engines have two banks of 6 cylinders oriented at 180 degrees from each other in a Flat engine, horizontally opposed or "flat" layout. This layout was first utilized in a Ferrari engine by engineer Mauro Forghieri in the 1964 Ferrari 158, Ferrari 1512 Formula One racing car, which was the first flat-12 car of any type to race. Ferrari had previously only manufactured engines with V engine, V or Straight engine, straight cylinder layouts. The flat-12 engine was initially developed for use in Ferrari racing cars because the shape of the engine resulted in a lower center of gravity, which improved various handling dynamics. In the later Ferrari 312B, 312 B and Ferrari 312T, 312 T F1 cars, the low height of the flat-12 was aerodynamically advantageous, as it allowed additional airflow to reach the rear Spoiler (car), spoiler.
All Ferrari flat-12 engines have a crankshaft design where each pair of opposing Connecting rod, connecting rods use the same crank pin, a trait shared with earlier Ferrari V12 engines. This distinguishes this engine design from a Flat engine#Boxer configuration, boxer engine. According to engine designer Forghieri:
Three names for the Ferrari flat-12 engines are in common use: "flat-12", "180° V12" and "boxer." "Flat-12" does not specify crankshaft design and therefore can refer to either a non-boxer engine like the Ferrari or a true boxer engine like a Porsche flat-six engine, Porsche flat-6. Alternatively, some sources prefer to call Ferrari flat-12 engines a "180° V12", referring to the V12-derived crankshaft design and the 180° angle between cylinder banks. Other sources refer to them as "boxer" engines. Despite the technical inaccuracy of "boxer", this term is widely used both in the press and official Ferrari publications, including the factory-issued specifications of the 312 B F1 and sales brochures for the BB 512 road car.
Ferrari's first flat-12 engine design was the 1.5-liter ''Tipo 207'', used in the 1964-65 Ferrari 158#Ferrari 1512, Ferrari 1512 Formula One car (also known as the 512 F1). The ''Tipo 207'' flat-12 engine was designed by Mauro Forghieri and displaced with a bore and stroke of and a compression ratio of 9.8:1. The crankcase was cast from aluminum alloy. The crankshaft ran in seven main bearings. Four gear-driven overhead camshafts operated one intake and one exhaust valve per cylinder. The ignition system used twin distributors (chain-driven off the timing gears) and a single spark plug per cylinder. Ancillary components such as the alternator, fuel pump and injection pumps were placed on top of the engine. The first version of the ''Tipo'' ''207'' engine, presented to the press at Ferrari's December 1963 press conference, was equipped with an Indirect injection, indirect fuel injection system manufactured by Lucas Industries, Lucas. This was changed to a full Robert Bosch GmbH, Bosch injection and ignition system prior to the car's competition debut in 1964. In 1965, the engine was revised with a new cylinder head design and revised injection trumpets.
The engine developed @ 12,000 rpm, compared to the @ 11,000 rpm of the 158's V8 engine, V8 engine. This power output made it one of the most powerful contemporary 1.5-litre Formula One engines, possibly surpassed by Honda's Honda RA271, RA271 V12. However, the engine's torque curve was not broad enough to provide a significant advantage over other cars and the 1512 was not competitive by the end of the 1965 season.
The ''Tipo 001'' was a 3-litre flat-12 used in Ferrari 312B, 312 B Formula One cars and Ferrari 312 PB, 312 PB sports racing cars between 1970 and 1974. Designed by Mauro Forghieri, this engine was intended to replace the aging Ferrari Colombo engine, Colombo V12 used in the Ferrari 312, 312 F1 and Ferrari 312 P, 312 P sports racing cars. The ''Tipo 001'' was the first Ferrari F1 engine funded by Fiat, after History of Ferrari#1969 %E2%80%93 Fiat, Fiat took a 50% stake in the company in 1969. Fiat's restructuring of the racing program and additional funding led Forghieri to create a new, separate R&D department where the 312 B F1 car and ''Tipo 001'' engine were developed. Forgheri was strongly influenced by the Cosworth DFV V8 engine when designing the ''Tipo 001'', particularly in how the movement of oil inside the crankcase was optimized to reduce oil pumping losses and the design of the combustion chamber.
The overall capacity of the engine was , with a bore and stroke of 78.5 mm x 51.5 mm and a compression ratio of 11.8:1. Later versions used in the 312 B2 and B3 had a bore and stroke of 80 mm x 49.6 mm and a compression ratio of 11.5:1. The aluminum alloy crankcase (with cast iron liners) was made in two pieces, with a vertical split at the center of the case. In order to reduce weight, Shot peening, shot-peened titanium Connecting rod, connecting rods were used. The one-piece machined crankshaft ran in four main bearings and was coupled to the flywheel with a rubber coupling (developed by Pirelli) that reduced stress on the crankshaft, preventing breakage. Like the previous ''Tipo 232'', four overhead camshafts were driven by gears and operated two intake and two exhaust valves per cylinder. The included angle between the valves was further reduced to 20°. Lucas indirect fuel injection and single-plug Marelli transistor ignition were equipped. The overall engine height was reduced compared to the earlier ''Tipo 207'' F1 engine and the engine was only heavier than the rival Cosworth DFV V8, despite having 4 additional cylinders and larger overall dimensions.
Ferrari initially reported the ''Tipo 001'' produced a power output of at 11,500 rpm, which exceeded the power output of both the earlier 312's V12 and the DFV by almost . By the end of the 1970 Formula One season, further development increased the ''Tipo 001''
File:1973 Ferrari F110 A - 52038303406.jpg, F110 A engine, with Bosch K-Jetronic air/fuel metering unit visible at left
File:1973 Ferrari F110 A.jpg, F110 A engine with covers partially cut away to show timing belt arrangement
File:Ferrari Engine older V12.jpg, F110 A engine in a BB 512i
File:1984 Ferrari F113 A - 52038302501.jpg, Right side of a F113 A engine
File:1984 Ferrari F113 A.jpg, Left side of a F113 A engine
File:SC06 1991 Ferrari Testarossa engine.jpg, F113 A engine in a Testarossa
Configuration and nomenclature
Ferrari flat-12 engines have two banks of 6 cylinders oriented at 180 degrees from each other in a Flat engine, horizontally opposed or "flat" layout. This layout was first utilized in a Ferrari engine by engineer Mauro Forghieri in the 1964 Ferrari 158, Ferrari 1512 Formula One racing car, which was the first flat-12 car of any type to race. Ferrari had previously only manufactured engines with V engine, V or Straight engine, straight cylinder layouts. The flat-12 engine was initially developed for use in Ferrari racing cars because the shape of the engine resulted in a lower center of gravity, which improved various handling dynamics. In the later Ferrari 312B, 312 B and Ferrari 312T, 312 T F1 cars, the low height of the flat-12 was aerodynamically advantageous, as it allowed additional airflow to reach the rear Spoiler (car), spoiler.
All Ferrari flat-12 engines have a crankshaft design where each pair of opposing Connecting rod, connecting rods use the same crank pin, a trait shared with earlier Ferrari V12 engines. This distinguishes this engine design from a Flat engine#Boxer configuration, boxer engine. According to engine designer Forghieri:
Three names for the Ferrari flat-12 engines are in common use: "flat-12", "180° V12" and "boxer." "Flat-12" does not specify crankshaft design and therefore can refer to either a non-boxer engine like the Ferrari or a true boxer engine like a Porsche flat-six engine, Porsche flat-6. Alternatively, some sources prefer to call Ferrari flat-12 engines a "180° V12", referring to the V12-derived crankshaft design and the 180° angle between cylinder banks. Other sources refer to them as "boxer" engines. Despite the technical inaccuracy of "boxer", this term is widely used both in the press and official Ferrari publications, including the factory-issued specifications of the 312 B F1 and sales brochures for the BB 512 road car.
Racing engines
Tipo 207
Ferrari's first flat-12 engine design was the 1.5-liter ''Tipo 207'', used in the 1964-65 Ferrari 158#Ferrari 1512, Ferrari 1512 Formula One car (also known as the 512 F1). The ''Tipo 207'' flat-12 engine was designed by Mauro Forghieri and displaced with a bore and stroke of and a compression ratio of 9.8:1. The crankcase was cast from aluminum alloy. The crankshaft ran in seven main bearings. Four gear-driven overhead camshafts operated one intake and one exhaust valve per cylinder. The ignition system used twin distributors (chain-driven off the timing gears) and a single spark plug per cylinder. Ancillary components such as the alternator, fuel pump and injection pumps were placed on top of the engine. The first version of the ''Tipo'' ''207'' engine, presented to the press at Ferrari's December 1963 press conference, was equipped with an Indirect injection, indirect fuel injection system manufactured by Lucas Industries, Lucas. This was changed to a full Robert Bosch GmbH, Bosch injection and ignition system prior to the car's competition debut in 1964. In 1965, the engine was revised with a new cylinder head design and revised injection trumpets.
The engine developed @ 12,000 rpm, compared to the @ 11,000 rpm of the 158's V8 engine, V8 engine. This power output made it one of the most powerful contemporary 1.5-litre Formula One engines, possibly surpassed by Honda's Honda RA271, RA271 V12. However, the engine's torque curve was not broad enough to provide a significant advantage over other cars and the 1512 was not competitive by the end of the 1965 season.
Tipo 232
The 2-liter ''Tipo 232'' flat-12 engine was developed for the 1968 Ferrari Sport 2000 (later called Ferrari 212 E Montagna, 212 E Montagna) Sports car racing, sports racing car. The engine was designed by Ferrari engineer Stefano Jacoponi, based on the earlier Forghieri-designed ''Tipo 207'' flat-12. Overall capacity of this engine was , bore and stroke was 65 mm x 50 mm and the compression ratio was 11:1. The crankcase was aluminum alloy with cast-iron cylinder liners. While the displacement was increased over the ''Tipo 207'', the ''Tipo 232'' was more compact. It had four main bearings (instead of the seven used on the earlier engine), the 27° included angle between the intake and exhaust valves was narrower and ancillary ignition/fuel injection components were mounted lower. Like the ''Tipo 207'', the engine used four gear-driven overhead camshafts, but now operating two intake and two exhaust valves per cylinder. Fuel was delivered by a Lucas indirect injection system. A Magneti Marelli transistorized ignition system was equipped, using a single spark plug per cylinder. When first installed in the Sport 2000, the engine produced at 11,500 rpm. Later during the 1969 racing season the engine was further developed and the compression ratio increased to 11.3:1. and could produce for short bursts and consistently. The engine was specialized for the short courses of the European Hill Climb Championship (where it was extremely successful in 1969) and was not intended for endurance events, although sufficient water and oil cooling systems were incorporated to prevent frequent engine rebuilds.Tipo 001
The ''Tipo 001'' was a 3-litre flat-12 used in Ferrari 312B, 312 B Formula One cars and Ferrari 312 PB, 312 PB sports racing cars between 1970 and 1974. Designed by Mauro Forghieri, this engine was intended to replace the aging Ferrari Colombo engine, Colombo V12 used in the Ferrari 312, 312 F1 and Ferrari 312 P, 312 P sports racing cars. The ''Tipo 001'' was the first Ferrari F1 engine funded by Fiat, after History of Ferrari#1969 %E2%80%93 Fiat, Fiat took a 50% stake in the company in 1969. Fiat's restructuring of the racing program and additional funding led Forghieri to create a new, separate R&D department where the 312 B F1 car and ''Tipo 001'' engine were developed. Forgheri was strongly influenced by the Cosworth DFV V8 engine when designing the ''Tipo 001'', particularly in how the movement of oil inside the crankcase was optimized to reduce oil pumping losses and the design of the combustion chamber.
The overall capacity of the engine was , with a bore and stroke of 78.5 mm x 51.5 mm and a compression ratio of 11.8:1. Later versions used in the 312 B2 and B3 had a bore and stroke of 80 mm x 49.6 mm and a compression ratio of 11.5:1. The aluminum alloy crankcase (with cast iron liners) was made in two pieces, with a vertical split at the center of the case. In order to reduce weight, Shot peening, shot-peened titanium Connecting rod, connecting rods were used. The one-piece machined crankshaft ran in four main bearings and was coupled to the flywheel with a rubber coupling (developed by Pirelli) that reduced stress on the crankshaft, preventing breakage. Like the previous ''Tipo 232'', four overhead camshafts were driven by gears and operated two intake and two exhaust valves per cylinder. The included angle between the valves was further reduced to 20°. Lucas indirect fuel injection and single-plug Marelli transistor ignition were equipped. The overall engine height was reduced compared to the earlier ''Tipo 207'' F1 engine and the engine was only heavier than the rival Cosworth DFV V8, despite having 4 additional cylinders and larger overall dimensions.
Ferrari initially reported the ''Tipo 001'' produced a power output of at 11,500 rpm, which exceeded the power output of both the earlier 312's V12 and the DFV by almost . By the end of the 1970 Formula One season, further development increased the ''Tipo 001''Tipo 015
The 3-liter ''Tipo 015'' flat-12 engine was used in the Ferrari 312T, Ferrari 312 T series of Formula One cars between 1975 and 1980. It was heavily derived from the ''Tipo 001'', but was adapted to fit the 312 T's new transverse gearbox. The overall capacity of the engine was with a bore and stroke of 80 mm x 49.6 mm and a compression ratio of 11.5:1. The engine's design was continuously improved during its years of competition, including increased use of lightweight magnesium and titanium components and refinements to the cylinder heads, combustion chambers and intake ducting. The first 312 T engines produced approximately at 12,200 rpm.This increased to at 12,200 rpm in the 1978 312 T3 and finally at 12,300 rpm in the 1979 312 T4. The ''Tipo 015'' was succeeded by the ''Tipo 021'' turbocharged V6 in the 1980 Ferrari 126C, 126C. The ''Tipo 015'' was Ferrari's last naturally-aspirated engine until 1989.Roadgoing engines
Ferrari introduced a roadgoing flat-12 engine with the 1973 Ferrari Berlinetta Boxer, 365 GT4 BB. This engine was further developed for use in 512 BB, 512 BBi, Testarossa, 512TR and F512M models, remaining in production until 1996.Tipo F102A
The ''Tipo F102A'' engine was the first flat-12 cylinder configuration fitted in a Ferrari road car, the 1973-1976 365 GT4 BB. Design and development of the new engine was overseen by Ferrari engineer Giuliano de Angelis and Angelo Bellei. The F102A engine's was derived from the ''Tipo 001'' Formula One engine as well as earlier Ferrari Colombo engine, Ferrari Colombo V12 engines. The engine's displacement, bore & stroke, rods and pistons were the same as the ''Tipo 251'' 60° V12 Colombo engine powering the Ferrari Daytona, 365 GTB/4 Daytona it replaced. The F102A had two valves per cylinder and twin overhead camshafts per bank, although these were now belt driven, instead of by chain as on earlier Ferrari 12-cylinder engines. Belt drive was chosen to reduce noise, improve reliability and reduce manufacturing and servicing costs. The engine fitted with two banks of two triple-choke Weber Carburetors, Weber 40IF3C carburettors and an electronic Magneti Marelli "Dinoplex" ignition system. In contrast to both the ''Tipo 251'' and the ''Tipo 001'', the spark plugs enter the combustion chamber from the top, rather than the sides. The Cylinder block, block and Cylinder head, cylinder heads were constructed from Silumin light alloy, with Borgo light alloy pistons, shrunk-in cast iron cylinder liners and a Crossplane, cross-plane, forged steel crankshaft. As was standard Ferrari practice, the crankshaft was machined from a single billet of steel, which was aged prior to machining in order to improve structural stability. The engine was lubricated by a wet sump with a capacity of and twin oil filters. According to de Angelis and Bellei, the first prototype F102 A engine produced at 7,100 rpm and propelled the prototype to during testing. Some Ferrari sales materials quote this 380 bhp figure, while others reported the production version of the F102 A engine produced 360 bhp at 7,500 rpm and 311 ft/lb of torque at 4,500 rpm. Figures reported in other factory and press publications vary, with the owner's manual reporting 344 PS (253 kW; 339 hp) at 7200 rpm.Tipo F102B
In 1976 Ferrari launched a revised version of the BB, the Ferrari Berlinetta Boxer#BB 512, BB 512. This car was equipped with a ''Tipo F102B'' flat-12 engine enlarged to 4943cc. This engine was based on the preceding F102A, but enlarged to 4943 cc. Bore and stroke were now 82 mm x 78 mm and the compression ratio was increased to 9.2:1. Camshaft timing was also altered. Ferrari initially claimed a peak power output of at 6800 rpm and of torque. Later Ferrari publications revised this to . Despite the loss in peak power, the flatter torque curve of the 4.9 liter engine provided a smoother and more user friendly power delivery. The larger displacement engine also allowed Ferrari to meet more stringent pollution and noise regulations without losing performance. A dry sump lubrication system was now used to prevent oil starvation and surge issues, which were exacerbated by the higher cornering forces generated by the BB 512's wider tires. The F102B engine was also used in Ferrari Berlinetta Boxer#512 BB LM, 512 BB LM racing cars. In series 1 cars, the engines were modified with new pistons, camshafts and carburetors, resulting in a power output of approximately . Series 2 cars also had a Lucas mechanical fuel injection system, fed by dual Turolla fuel pumps. In this form, the engine generated approximatelyTipo F110A
In 1981 the BB 512 was replaced by the BB 512i, powered by the ''Tipo F110A'' engine. This engine was based on the F102B but was now equipped with Bosch Jetronic#K-Jetronic (1973%E2%80%931994), K-Jetronic fuel injection. It had the same dimensions and overall capacity as the F102B. The fuel injection system allowed Ferrari to meet stricter emissions regulations. Overall power output was now at 6,000 rpm. The Dinoplex electronic ignition system now had a built-in rev limiter that activated at 6,600 rpm.Tipo F113A/B/D/G
The Ferrari Testarossa, Testarossa was introduced in 1984, replacing the BB 512i. It was equipped with the ''Tipo F113A'' engine. This engine was the first roadgoing Ferrari flat-12 engine with four valves per cylinder. The power output was , making it the most powerful engine mounted on a production sports car at the time of its launch. The bore and stroke and 4943cc cubic capacity was identical to the preceding F110A engine. The F113A was fitted with a Marelli Microplex MED120 electronic ignition system and Bosch K-Jetronic fuel injection. Export versions for United States, Canada and Japan had catalytic converter and KE-Jetronic fuel injection. European versions got those features in 1986 and the revised engine was known as F113B. The 1991 Ferrari 512 TR, 512 TR was equipped with the ''Tipo F113D'' engine. This was an upgraded version of the F113A in the Testarossa, maintaining the same cubic capacity of 4.9 L. Changes were made to the porting, with redesigned inlet plenums and larger valves providing more efficient fuel/air mix ingress, whilst the fuel injection and ignition system were changed to a combined Bosch Motronic#2.7, Motronic M2.7 system. The engine was further improved with new shallow-skirt pistons and a modified crankshaft design. This engine produced at 6,750 rpm and at 5,500 rpm. For the 1994 Ferrari F512M, F512M the engine was further upgraded and designated ''Tipo F113G''. This engine had a lightened crankshaft, titanium alloy Connecting rod, connecting rods, new pistons and a stainless steel low backpressure exhaust system. The compression ratio increased to 10.4:1. The F113G produced at 6,750 rpm. The flat-12 production ceased with the F512M, being replaced by the front-engined Ferrari 550 Maranello, 550 Maranello which featured the new 65° V12 Ferrari F116/F133 engine, F133 engine.Aircraft engine
In the late 1960s, Ferrari was approached by Franklin Engine Company with an order for an engine that could be installed in a small twin-engined aircraft. Mauro Forghieri began adapting a flat-12 engine design for this purpose, as this configuration would fit within a wing. However, the project was quickly cancelled when Franklin entered receivership. Forghieri's design work on the aircraft engine was incorporated into the 1970 ''Tipo 001'' racing flat-12 engine.Specifications
See also
*List of Ferrari enginesReferences
{{Ferrari Ferrari engines Flat engines Gasoline engines by model 12-cylinder engines