Black and burst
   HOME

TheInfoList



OR:

Black and burst, also known as bi-level sync and black burst, is an analogue signal used in broadcasting. It is a
composite video Composite video is an analog video signal format that carries standard-definition video (typically at 525 lines or 625 lines) as a single channel. Video information is encoded on one channel, unlike the higher-quality S-Video (two channe ...
signal with a black picture. It is a reference signal used to synchronise video equipment, in order to have them output video signals with the same timing. This allows seamless switching between two video signals. Black and burst can also be used to synchronise colour phase and provides timing accuracy in the order of tens of nanoseconds which is necessary to perform e.g. analogue video mixing. Black and burst exists for various colour TV standards, such as
PAL Phase Alternating Line (PAL) is a colour encoding system for analogue television. It was one of three major analogue colour television standards, the others being NTSC and SECAM. In most countries it was broadcast at 625 lines, 50 fields (25 ...
,
NTSC The first American standard for analog television broadcast was developed by National Television System Committee (NTSC)National Television System Committee (1951–1953), Report and Reports of Panel No. 11, 11-A, 12–19, with Some supplement ...
and
SECAM SECAM, also written SÉCAM (, ''Séquentiel de couleur à mémoire'', French for ''color sequential with memory''), is an analog color television system that was used in France, some parts of Europe and Africa, and Russia. It was one of th ...
. Because the black and burst signal is a normal video signal, it is transportable via normal video cables and through video distribution equipment.


History

Before colour TV existed, the reference signal was also a black video signal. Inaccuracies meant the video picture would be shifted. With the introduction of colour, the reference had to be much more accurate. In every composite video signal a reference burst is present in the horizontal sync portion, so all equipment in the chain will be synchronised roughly 16000 times per second. This regular synchronisation is necessary because the colour information is transmitted via
quadrature amplitude modulation Quadrature amplitude modulation (QAM) is the name of a family of digital modulation methods and a related family of analog modulation methods widely used in modern telecommunications to transmit information. It conveys two analog message signa ...
on the high-frequency colour signal. Incorrect synchronisation means the phase will be off, and consequently the colour will be incorrect. Creating broadcast television usually involves mixing video signals. When doing this in an analogue way, it is essential that all signals have the same colour phase, which was achieved by synchronising all cameras with a black and burst signal. Because of cable length differences, every camera required a (often only slightly) different timing. This could be tuned at the reference source, and/or at the camera. Black and burst is being replaced by
tri-level sync Tri-level sync is an analogue video synchronization pulse primarily used for the locking of high-definition video signals (genlock). It is preferred in HD environments over black and burst, as timing jitter is reduced due to the nature of its ...
, but as of 2020 it is still quite common. Because the signal chains are now digital, which allows buffering, the timing requirements are not as strict anymore.


Waveform

Its natural waveform is a negative pulse with a level of -40
IRE Ire or IRE may refer to: Ire * Extreme anger; intense fury * Irē, the Livonian name for Mazirbe, Latvia * A town in Oye, Nigeria * ''Ire'' (album), a 2015 album by the Australian metalcore band Parkway Drive * Ire (Iliad), a town mentioned in ...
followed by 10 cycles of the colour sub carrier of video. For most variants of PAL video, the frequency of the sub carrier is 4.43361875 MHz.


See also

*
Genlock Genlock (generator locking) is a common technique where the video output of one source (or a specific reference signal from a signal generator) is used to synchronize other picture sources together. The aim in video applications is to ensure the ...
* SMPTE 2059


References

{{reflist Synchronization Film and video technology Broadcast engineering Television terminology