Preamble
There are in Belgium two types of train movement: * 'major movement' (e.g. mainline operation) that occurs during normal operation (traffic moves at the speed permitted by the signalling and regulations); * 'minor movement' (e.g. shunting) which is done by driving by sight and never faster than . The change from one movement to the other is done by signals (main stop signals) or a written order. The ''first movement'' (which is always executed as minor movement) happens in the following situations: * a driver taking over a new train; * a change in driver's cab or direction of travel; * receipt, change or removal of train number; * vehicles that can drive on themselves are coupled or uncoupled * when permission is needed to continue to drive after an incident * when beginning to shunt Within major movement, there are two regimes, linked to bi-directional operation on double track lines: * ''normal track regime'': the signals are located on the left of the track. However, in some cases, the configuration of the environment precludes placing signs on the left track. They are then placed on the right and have an arrow (white arrow on a blue disc). * ''counter-flow track regime'': the signals are located on the right of the track and the aspects are blinking. The most common way of regime change is by the display of a chevron (V-shaped) sign on a main stop sign (single or combined). In ''minor movement'', all signals are to be obeyed, both those of the left hand track and the right hand; signals controlling only minor movements are placed on the left. In counter-flow operation, some signals (light or otherwise) are specifically dedicated to minor movements and therefore are ignored by the trains travelling in ''major'' movement.Light signals
The lights are designed and arranged to be visible from a distance (up to two kilometers on a clear day). For this they are equipped with lenses to focus light rays emitted by the bulb, which can be selected and reasonable power. That is why the lights do not seem very intense when viewed from the side while they light up sharply in normal line of vision i.e. in the direction of arrival of the train. Note that the yellow lights often are orange in reality.Plain stop signal
The red aspect requires a halt for both major and minor movements. It can be opened for major movement (green when the track gives access to a mainline, or double yellow in stations) or minor movement (red + white). It gives no information about the aspect of the next signal. A white number below the main aspect restricts the speed (from the first switch or track junction after the signal). Above the main aspect, the signal can show a chevron (to change the regime), or a "U" (when the train is led towards a dead end). It can be mounted on a mast or gantry (above the track).Warning signal
Warns of the aspect of a following main stop signal:Combined main stop signal
Serves as both a stop signal and a warning signal and can therefore, according to the needs of the position, present aspects of both a plain stop signal and a warning signal. This type of signal is the most common one on the mainline network.Simplified stop signal
It can either be placed at ground level or elevated (on a post).Small stop signal
It is placed on the ground. An older version of the small stop signal has the appearance of the simplified signal above, but with a purple instead of a red light.Completed operations indicator (IOT)
The Completed operations indicator is a system composed of a set of switches (activation) and light signals (display) on platforms of most stations and allows the guard to announce to the driver (conductor) that the procedure for boarding is completed and the train can start. Where the system is installed, the yellow aspect (or white on older systems) is a prerequisite for the departure of passenger trains.Aspects displayed by major stop signals and warning signals
Signs
Speed signs
Additional panels (''special'' triangles, for example) are used to indicate that only certain types of trains are affected: e.g., "HKM" means the sign only concerns freight trains .Some other signs
Other signals
Other signals complement the fixed signs: * Mobile signals (light at night / low visibility, flag day) red, yellow and green; * Acoustic signals (detonators, horns); * Torch flame red lights flashing (requiring 'halt');Cab signalling
The TBL1+ system was designed in 2006 by the Belgian subsidiary of the Alstom Transport group. This is the new standard for Belgian signalling, supposed to be deployed on most lines equipped with conventional signalling. The signals are the same as classic ones, but they are combined with automatic train control and cab signalling. The trigger for developing this system was the Pécrot disaster in March 2001 when two trains collided head-on because a driver had passed a red signal, highlighting the finding that the majority of lines, no system prevented the train from passing a stop signal. It was therefore decided to invest in such a system. At the time, however, the existing TBL1 system offered this feature of automatic stop at red lights, but only a few main lines were equipped (or approximately 13% of signals). NMBS/SNCB decided therefore to abandon this TBL1 system and modified to make it compatible with the new European ERTMS standard in terms of ground infrastructure, becoming the system TBL1+. Today, the TBL1+ system is undergoing testing and certification. It will be installed from 2008, the objective being to equip the entire network by 2013. Status of introduction of TBL1+Basics
The TBL1+ system is a system of driving aids to repeat the signals aspects in the cab, and to intervene if the driver does not comply with the directions given by these signals. Unlike systems such as ERTMS TBL2 which supervise a speed curve, the TBL1+ system does only a spot-check when passing light signals. This is done with a beacon placed in the track, which transmits to the onboard computer a message containing the signal aspect. We can classify the appearance of a signal into three broad categories:Clear aspect
This aspect indicates that the track is clear and allows the train to run at maximum speed allowed. This is typically a green signal. When the train passes a signal as the TBL1+ system simply repeats information and makes a short sound in his cab (the lamps used to indicate a possible restriction are also extinct).Restrictive aspects
This type of aspect requires the driver to slow, for example, because the next signal shows a non-clear aspect (double yellow) or imposes a speed limit (yellow-green horizontal). When the train passes a signal as the driver must confirm that he saw the signal by pushing a button, otherwise the system will apply the emergency brake. In addition, a yellow lamp is lit in the cabin to remind the driver that runs under a restrictive regime.Stop aspect
This type of aspect (typically a red signal) instructs the driver to halt and can not be passed by a train (except with a special procedure). If the train passes a signal showing a stop aspect, the TBL1+ system immediately applies the emergency brake and flashes a red light in the cab, forcing the train to stop completely and as quickly as possible. Although TBL1+ does not control the speed curve, the system does include a reduced speed control. In this mode, indicated by the "V <40" LED display, the train speed can not exceed , otherwise the emergency brake is applied. This mode is used for shunting, and also the approach of a stop signal, so as to operate an advance emergency braking if the train passes a warning signal at a too high speed. Switching to this mode can be done manually by the driver or automatically using the beacon on the ground.Ground equipment
In both TBL1 or TBL2 the aspect of the signal is transmitted to the train through beacons placed in the right way for this signal using an encoder to translate the appearance of this signal into computer message (i.e. a sequence of bits). The big difference with the previous systems is the fact that the TBL1+ beacons are identical to those used for lines equipped with ERTMS, while the message is compatible with the standard set by ERTMS UNISIG. Therefore, it is quite possible to migrate a line equipped TBL1+ to ERTMS, or even superimpose the two systems without having to change the ground beacons. The TBL1+ system is also compatible with the old system MEMOR, which used "On board equipment
The TBL1+ interface between the driver and the onboard computer consists only of lights and buttons. Here are the main ones: The alert button is used to acknowledge the passing of a restrictive signal. It also helps to release the emergency brake when equipment TBL1+ train stopped. The yellow light flashes when the train passes a signal showing restrictive aspects to request acknowledgement from the driver, and then remains lit until the train has not met unrestricted signal (but it may be turned off by pressingon this indicator). The red light flashes when the emergency brake is triggered after the train passes a stop signal, and then remains lit until the train comes to the next signal showing 'track clear'. (it can however be switched off by pressing the light). "V <40" and "V> 40" displays indicate whether the TBL1+ system is in "control of low speed" or not. The manual shift mode to another is done by pressing the corresponding LED. The button permits temporary disablement of the system, following a strict procedure, temporarily disabling the system to pass signals in such trouble. The onboard computer is connected to an antenna to read ERTMS tags placed in the path, and a brush-crocodile to capture the information transmitted byOther cab signalling systems
* TVM 430 on the line 1 *TBL2 on the Line 2 and *References
External links