The "Beep" (also referred to as the SWBLW) is an individual switcher locomotive built in 1970 by the Atchison, Topeka and Santa Fe Railway at its Cleburne, Texas, workshops. Technically a rebuild, the Beep (a portmanteau of a B-B wheel arrangement and "Baldwin Rail terminology#G, Geep", whose official designation was derived from "SWitcher, Baldwin Locomotive Works") originally entered service on the Santa Fe as a Baldwin Locomotive Works, Baldwin Model Baldwin VO-1000, VO-1000. Following its successful CF7 capital rebuilding program, the company hoped to determine if remanufacturing its aging, non-EMD end cab switchers by fitting them with new EMD Prime mover (locomotive), prime movers was an economically viable proposition. The conversion procedure proved too costly and only the one unit was modified. In 2008-2009, this locomotive was retired and stored operational at Topeka, Kansas. In May 2009 the unit was donated to the Western America Railroad Museum in Barstow, California.

History

In the early 1960s the Reading Company sent 14 of their VO-1000s to Electro-Motive Diesel, General Motors Electro-Motive Division to have them rebuilt to EMD SW900, SW900 specifications. Unlike the "Beep", these locomotives retained most of their original carbodies. The units were subsequently given the designation Baldwin VO-1000, VO-1000m.

Development

VO-1000 No. 67729 emerged from the Baldwin Locomotive Works Eddystone, Pennsylvania, facility in July 1943 dressed in the Santa Fe ''Zebra Stripe'' livery and bearing #2220. In the early 1960s the unit would take on the blue and yellow ''Billboard'' paint scheme with "SANTA FE" displayed in small yellow letters above the accent stripe, as was the standard for all Railroad yard, yard switchers. It is these colors that #2220 displayed when it was selected as a test subject. Much as with the CF7 conversions, the unit was stripped down to its bare frame, and the long hood, power plant, Bogie, trucks, control gear, and electrical system scrapped; only the Baldwin cab remained. In a manner similar to the first CF7 modification, a sixteen-cylinder EMD 567 series diesel engine was fitted to the Baldwin's cast steel frame, which required a considerable amount of modification. A new long hood was fabricated by the shops to a EMD GP7, GP7 pattern. The locomotive was configured in a AAR wheel arrangement#B-B, B-B wheel arrangement and mounted atop two Blomberg B two-axle bogie, trucks, with all axles powered. The unit received an advanced electrical system. The completed Beep rolled out of the Cleburne shops in December 1970 (with one of its original Baldwin builder's plates still affixed) sporting fresh blue and yellow paint, though now the words "Santa Fe" were applied in yellow in Cooper Black font (logotype) along the sides below the accent stripe in the style otherwise reserved for road switchers and other Main line (railway), main line locomotives. It was also assigned #2450 (the first CF7 was given #2649, with successive numbers applied in descending order) and placed in service in south Texas.

In service

Train crews favored #2450 due to the superior riding qualities of its Blomberg trucks, which ran more smoothly than the original Association of American Railroads, AAR Type-A switcher trucks. Being several tons heavier than a typical GP7 imparted a higher tractive effort, helpful when switching long cuts of cars. The Beep spent many years in lease service performing switching duties for the Port Terminal Railroad Association in Houston. In August, 1974 the unit was re-designated as #1160 as part of a general locomotive renumbering scheme. It was again renumbered along with the Santa Fe's few remaining EMD switchers and assigned #1460 in January, 1977. The Beep was transferred to Cleburne as the shop switcher in the mid-1980s, where in 1985 it was given a number of external modifications. A cab air conditioner, air conditioning system was added, and the rear cab windows were modified from their original Baldwin pattern to a new three-pane configuration that accommodated the use of standard window glass sizes common to many EMD locomotives. The unit was given fresh paint (the ''Billboard'' colors were maintained) and placed back in service. SW900 #1453, Santa Fe's last "standard" EMD switcher, was retired in 1987, thus making #1460 the only end cab switcher on the roster. The Beep continued working at Cleburne until the shops were closed later that year. Since then, the unit has worked as a shop switcher at both the Argentine shops in Kansas City, Kansas, Kansas City and in Topeka, Kansas. The locomotive was equipped with remote control equipment (RCE) in the early 1990s so that it could be operated from a distance. After Santa Fe merged with the Burlington Northern Railroad in 1995-1996 to form BNSF Railway, the Beep was one of only three blue and yellow units not affected by the new company's renumbering program. #1460's cab sides were affixed with a BNSF sublettering "patch" and retrofitted with a four-stack exhaust manifold.http://atsf.railfan.net/beep/sf1460ekimmel.jpg It was retired in 2008-2009, and later stored in Topeka, Kansas. In May 2009, the unit was donated to the Western America Railroad Museum in Barstow, California, where it remains on static display.

Footnote

Santa Fe had designated a handful of other non-EMD switcher locomotives for rebuilding around 1970 (including two Fairbanks-Morse FM H-10-44, H-10-44s), but all of these units were subsequently scrapped when it was determined that the required modifications were not cost effective.

References

* Bassett, Gordon C. (1991). "Modeling the 'Beep'." ''The Santa Fe Modeler'' 14 (1) 8–14. * Includes background information and a photo gallery. *

External links