BMW R100
   HOME

TheInfoList



OR:

BMW R100, with variant models designated by T, S, CS, RS, RS Classic, RT, RT Classic, TIC, TC, R and GS is a BMW
motorcycle A motorcycle (motorbike, bike, or trike (if three-wheeled)) is a two or three-wheeled motor vehicle Steering, steered by a Motorcycle handlebar, handlebar. Motorcycle design varies greatly to suit a range of different purposes: Long-distance ...
series, using a two-cylinder
four-stroke A four-stroke (also four-cycle) engine is an internal combustion (IC) engine in which the piston completes four separate strokes while turning the crankshaft. A stroke refers to the full travel of the piston along the cylinder, in either direct ...
boxer engine of 980 cc capacity. Model production began in 1976, with a premature shutdown and subsequent restart in 1985, and final completion of the series in 1996. The last of the " airheads," this article also discusses the different /7 models of smaller displacements (R60, R75, R80).


First (/7) and second series

The "slash seven" development was an evolutionary change of the
BMW 247 engine The BMW 247 engine is an air-cooled flat-twin motorcycle engine with two valves per cylinder, also known as the "airhead" boxer. It was used by BMW in its motorcycles from 1969 to 1995. The /5 variant was introduced in 1969, /6 in 1974 and the ...
from the previous " slash six" and initially constituted the R100RS (51 kW / 70 PS), R100S (48 kW / 65 PS), R100 (44 kW / 60 PS), R75/7 (37 kW / 50 PS) and R60/7 (30 kW / 40 hp). The R100RS was the first motorcycle manufactured in volume to be fitted as standard with a frame fixed full fairing, a feature pioneered by the Vincent Black Prince. This innovation was a departure from previous touring fairings, giving birth to the modern sport touring motorcycle.


Brakes

The R100 models received a double disc brake in the front wheel. For 1976 to 1979 models the front brake was a pivot caliper ATE disc actuated from the controls via cable to a brake master cylinder under the tank. From 1980 models onwards front brakes were changed to a Brembo fixed caliper brake, and the master cylinder was moved from undertank to the right handlebar. With the introduction of Monolever models in 1986, the Brembo fixed calipers were mounted on the fork tubes. The back brake was initially a drum brake. Starting in the 1978 model year (September 1977), the R100RS, RT and S models received a Brembo rear disc brake with fixed caliper on the rear wheel, and from model year 1985 the rear drum brake returned.


Wheels

The models originally were fitted with wire spoked wheels, but in September 1977 for the 78 model year shifted to an aluminum cast "snowflake" pattern. The initial aluminum wheels were prone to breakage, prompting a BMW recall for replacement.


Engine and drivetrain

In keeping with the evolutionary development of the Boxer line, the engine was a laterally opposed 2-cylinder boxer engine with lower camshaft and overhead valves. Driving the camshaft was a duplex (later simplex) chain with a spring-loaded chain tensioner. The clutch was a single dry plate with cable actuation. A 5-speed manual transmission, with an optional kickstarter for the early models, and shaft drive to the rear wheel completed the drivetrain.


Carburetor

A constant velocity
carburetor A carburetor (also spelled carburettor) is a device used by an internal combustion engine to control and mix air and fuel entering the engine. The primary method of adding fuel to the intake air is through the venturi tube in the main meteri ...
was supplied by Bing. Starting in 1980, an emissions control system was implemented in various countries, which reduced available horsepower by approximately 10%.


Suspension

The front forks were telescopic with a diameter of 36 mm without gaiters. 1984 and prior had a dual swing arm with two shock absorbers, model year 1986 and after used the BMW monolever, 1988 and after used the BMW paralever.


Ignition

Up to model year 1978, a points type high-voltage capacitor ignition was used. From 1978 onwards, an electronic ignition was fitted.


Specifications


Pause and Restart

In the 1980s for environmental and marketing reasons, BMW initiated a move to the water-cooled K75 and K100 models to remain competitive with the technical lead of the Japanese motorcycle industry. For this purpose they wanted to give up the production of the "airhead" two-valve boxer models. This decision led to protests from customers and dealers, BMW restarted R100 production, but with modified lower output, and improved torque curve engines with 44 kW (60 hp). They later produced an 800 cc version with 37 kW (50 hp). Starting in 1985, the road versions were equipped with a single-sided swingarm (Monolever). From 1988 Paralever rear suspension was introduced, first in the GS models R80G/S (later redesignated "R80GS") and R100GS, and later in the road versions R80R, R100R and in 1994 the R100 Mystic.


Sources

* Hans-Jürgen Schneider: ''BMW R 45 – R 100 RS ab Baujahr 1976: alle Modelle mit Zweizylinder-Boxermotor; Technik, Wartung, Reparatur'' BLV Auto- und Motorradpraxis, München Wien Zürich 1984, . * Don Morley, Mick Woollett: ''BMW.'' Heel Verlag, Königswinter 1994. . * Hans-Joachim Mai: ''1000 Tricks für schnelle BMWs.'' 11. Aufl. 1988, Motorbuch-Verlag, Stuttgart. * Andy Schwietzer, Werner R. Reiss: ''BMW Boxer alle ab /5: BMW Zweiventiler von 1969–1985.'' 1. Aufl. Bodensteiner-Verlag, Wallmoden 2006, . * Stefan Knittel: ''BMW Motorräder''. Gerlingen 1984, . R100RS Motorcycles powered by flat engines Shaft drive motorcycles {{Motorcycle-stub