Iron metallurgy in Africa

The topic of early iron-metallurgy in Africa encompasses both studies of the technology and archaeology of indigenous iron-production.

Some recent studies date the inception of iron metallurgy in Africa between 3000 and 2500 BCE. Evidence exists for earlier iron metallurgy in parts of Nigeria, Cameroon, and Central Africa, possibly from as early as around 2,000 BCE.
Some evidence from historical linguistics suggests that the Nok culture of Nigeria may have practiced iron smelting from as early as 1000 BCE. The nearby Djenné-Djenno culture of the Niger Valley in Mali shows evidence of iron production from 250 BCE. The Bantu expansion spread the technology to Eastern and Southern Africa during 500 BCE to 400 CE, as shown in the Urewe culture of the Lake Victoria region.

Iron has a number of advantages over copper, brass, wood, and stone. The use of iron ushered in an Iron Age in Africa, with the expansion of agriculture, industry, trade, and political power. In some African cultures, smelters and ironworkers are of low status because of the manual labor inherent in their work. In others, they are of high status because of the value of their wares.

Archaeological evidence for the origins and spread of iron production in Africa

Although the origins of iron working in Africa have been the subject of scholarly interest since the 1860s, it is still not known whether this technology diffused into sub-Saharan Africa from the Mediterranean region, or whether it was invented there independently of iron working elsewhere. Although some nineteenth-century European scholars favored an indigenous invention of iron working in sub-Saharan Africa, archaeologists writing between 1945 and 1965 mostly favored diffusion of iron smelting technology from Carthage across the Sahara to West Africa and/or from Meroe on the upper Nile to central Africa. This in turn has been questioned by more recent research which argues for an independent invention.

The invention of radiocarbon dating in the late 1950s enabled dating of metallurgical sites by the charcoal fuel used for smelting and forging. By the late 1960s some surprisingly early radiocarbon dates had been obtained for iron smelting sites in both Niger and central Africa (Rwanda, Burundi), reviving the view that iron-making was independently invented by Africans in sub-Saharan Africa as far back as 3600 BCE. These dates preceded the known antiquity of ironworking in Carthage or Meroe, weakening the diffusion hypothesis. In the 1990s, evidence was found of Phoenician iron smelting in the western Mediterranean (900–800 BCE), though specifically in North Africa it seems to date only to the 5th to 4th centuries BCE, or the 7th century BCE at the earliest, contemporary to or later than the oldest known iron metallurgy dates from sub-Saharan Africa. According to archaeometallurgist Manfred Eggert, "Carthage cannot be reliably considered the point of origin for sub-Saharan iron ore reduction." It is still not known when iron working was first practiced in Kush and Meroe in modern Sudan, but the earliest known iron metallurgy dates from Meroe and Egypt do not predate those from sub-Saharan Africa, and thus the Nile Valley is also considered unlikely to be the source of sub-Saharan iron metallurgy.

From the mid-1970s there were new claims for independent invention of iron smelting in central Niger and from 1994 to 1999 UNESCO funded an initiative "Les Routes du Fer en Afrique/The Iron Routes in Africa" to investigate the origins and spread of iron metallurgy in Africa. This funded both the conference on early iron in Africa and the Mediterranean and a volume, published by UNESCO, that generated some controversy because it included only authors sympathetic to the independent-invention view.

Two reviews of the evidence from the mid-2000s found technical flaws in the studies claiming independent invention, raising three major issues. The first was whether the material dated by radiocarbon was in secure archaeological association with iron-working residues. Many of the dates from Niger, for example, were on organic matter in potsherds that were lying on the ground surface together with iron objects. The second issue was the possible effect of "old carbon": wood or charcoal much older than the time at which iron was smelted. This is a particular problem in Niger, where the charred stumps of ancient trees are a potential source of charcoal, and have sometimes been misidentified as smelting furnaces. A third issue is the weaker precision of the radiocarbon method for dates between 800 and 400 BCE, attributable to irregular production of radiocarbon in the upper atmosphere. Unfortunately most radiocarbon dates for the initial spread of iron metallurgy in sub-Saharan Africa fall within this range.

Controversy flared again in 2007 with the publication of excavations by Étienne Zangato and colleagues in the Central African Republic. At Oboui they excavated an undated iron forge yielding eight consistent radiocarbon dates of 2000 BCE. This would make Oboui the oldest iron-working site in the world, and more than a thousand years older than any other dated evidence of iron in Central Africa. Opinion among African archaeologists is sharply divided. Some specialists accept this interpretation, but archaeologist Bernard Clist has argued that Oboui is a highly disturbed site, with older charcoal having been brought up to the level of the forge by the digging of pits into older levels. Clist also raised questions about the unusually good state of preservation of metallic iron from the site. However, archaeologists such as Craddock, Eggert, and Holl have argued that such disturbance or disruption is highly unlikely given the nature of the site. Additionally, Holl, regarding the state of preservation, argues that this observation was based on published illustrations representing a small unrepresentative number of atypically well-preserved objects selected for publication. At Gbabiri, also in the Central African Republic, Eggert has found evidence of an iron reduction furnace and blacksmith workshop with earliest dates of 896–773 BCE and 907–796 BCE respectively.
In north-central Burkina Faso, remains of a blast furnace near Douroula was also dated to the 8th century BCE, leading to the creation of the Ancient Ferrous Metallurgy Sites of Burkina Faso World Heritage Site.
In the Nsukka region of southeast Nigeria (now Igboland), archaeological sites containing iron smelting furnaces and slag have been excavated dating to 750 BCE in Opi (Augustin Holl 2009) and 2,000 BCE in Lejja (Pamela Eze-Uzomaka 2009). According to Augustin Holl (2018), there is evidence of ironworking dated to 2,153–2,044 BCE and 2,368–2,200 BCE from the site of Gbatoro, Cameroon.

In 2014, archaeo-metallurgist Manfred Eggert argued that, though still inconclusive, the evidence overall suggests an independent invention of iron metallurgy in sub-Saharan Africa. In a 2018 study, archaeologist Augustin Holl also argues that an independent invention is most likely.

While the origins of iron smelting are difficult to date by radiocarbon, there are fewer problems with using it to track the spread of ironworking after 400 BCE. In the 1960s it was suggested that iron working was spread by speakers of Bantu languages, whose original homeland has been located by linguists in the Benue River valley of eastern Nigeria and Western Cameroon. Although some assert that no words for iron or ironworking can be traced to reconstructed proto-Bantu, place-names in West Africa suggest otherwise, for example (Okuta) Ilorin, literally "site of iron-work". The linguist Christopher Ehret argues that the first words for iron-working in Bantu languages were borrowed from Central Sudanic languages in the vicinity of modern Uganda and Kenya, while Jan Vansina argues instead that they originated in non-Bantu languages in Nigeria, and that iron metallurgy spread southwards and eastwards to Bantu speakers, who had already dispersed into the Congo rainforest and the Great Lakes region. Archaeological evidence clearly indicates that starting in the first century BCE, iron and cereal agriculture (millet and sorghum) spread together southward from southern Tanzania and northern Zambia, all the way to the eastern Cape region of present South Africa by the third of fourth century CE. It seems highly probable that this occurred through migrations of Bantu-speaking peoples.

Techniques

All indigenous African iron smelting processes are variants of the bloomery process. A much wider range of bloomery smelting processes has been recorded on the African continent than elsewhere in the Old World, probably because bloomeries remained in use into the 20th century in many parts of sub-Saharan Africa, whereas in Europe and most parts of Asia they were replaced by the blast furnace before most varieties of bloomeries could be recorded. W.W. Cline's compilation of eye-witness records of bloomery iron smelting over the past 250 years in Africa is invaluable, and has been supplemented by more recent ethnoarchaeological and archaeological studies. Furnaces used in the 19th and 20th centuries ranges from small bowl furnaces, dug down from the ground surface and powered by bellows, through bellows-powered shaft furnaces up to 1.5 m tall, to 6.5m natural-draft furnaces (i.e. furnaces designed to operate without bellows at all).

Over much of tropical Africa the ore used was laterite, which is widely available on the old continental cratons in West, Central and Southern Africa. Magnetite sand, concentrated in streams by flowing water, was often used in more mountainous areas, after beneficiation to raise the concentration of iron. Precolonial iron workers in present South Africa even smelted iron-titanium ores that modern blast furnaces are not designed to use. Bloomery furnaces were less productive than blast furnaces, but were far more versatile.

The fuel used was invariably charcoal, and the products were the bloom (a solid mass of iron) and slag (a liquid waste product). African ironworkers regularly produced inhomogeneous steel blooms, especially in the large natural-draft furnaces. The blooms invariably contained some entrapped slag, and after removal from the furnace had to be reheated and hammered to expel as much of the slag as possible. Semi-finished bars of iron or steel were widely traded in some parts of West Africa, as for example at Sukur on the Nigeria-Cameroon border, which in the nineteenth century exported thousands of bars per year north to the Lake Chad Basin. Although many African ironworkers produced steel blooms, there is little evidence in sub-Saharan as yet for hardening of steel by quenching and tempering or for the manufacture of composite tools combining a hard steel cutting edge with a soft but tough iron body. Relatively little metallography of ancient African iron tools has yet been done, so this conclusion may perhaps be modified by future work.

Unlike bloomery iron-workers in Europe, India or China, African metalworkers did not make use of water power to blow bellows in furnaces too large to be blown by hand-powered bellows. This is partly because sub-Saharan Africa has much less potential for water power than these other regions , but also because there were no engineering techniques developed for converting rotary motion to linear motion. African ironworkers did however invent a way to increase the size of their furnaces, and thus the amount of metal produced per charge, without using bellows. This was the natural-draft furnace, which is designed to reach the temperatures necessary to form and drain slag by using a chimney effect – hot air leaving the topic of the furnace draws in more air through openings at the base. (Natural-draft furnaces should not be confused with wind-powered furnaces, which were invariably small). The natural-draft furnace was the one African innovation in ferrous metallurgy that spread widely. Natural draft furnaces were particularly characteristic of African savanna woodlands, and were used in two belts – across the Sahelian woodlands from Senegal in the west to Sudan in the east, and in the ''Brachystegia-Julbenardia'' (miombo) woodlands from southern Tanzania south to northern Zimbabwe. The oldest natural-draft furnaces yet found are in Burkina Faso and date to the seventh/eight centuries The large masses of slag (10,000 to 60,000 tons) noted in some locations in Togo, Burkina Faso and Mali reflect the great expansion of iron production in West Africa after 1000 CE that is associated with the spread of natural-draft furnace technology. But not all large scale iron production in Africa was associated with natural draft furnaces – those of Meroe (Sudan, first to fifth centuries CE) were produced by slag-tapping bellows-driven furnaces, and the large 18th-19th century iron industry of the Cameroon grasslands by non-tapping bellows-driven furnaces. All of the large-scale iron smelting recorded so far are in the Sahelian and Sudanic zones that stretch from Senegal in the west to Sudan in the east; there were no iron-smelting concentrations like these in central or southern Africa.

There is also evidence that carbon steel was made in Western Tanzania by the ancestors of the Haya people as early as 2,300-2,000 years ago by a complex process of "pre-heating" allowing temperatures inside a furnace to reach up to 1800  °C.

These techniques are now extinct in all regions of sub-Saharan Africa, except, in the case of some of techniques, for some very remote regions of Ethiopia. In most regions of Africa they fell out of use before 1950. The main reason for this was the increasing availability of iron imported from Europe. Blacksmiths still work in rural areas of Africa to make and repair agricultural tools, but the iron that they use is imported, or recycled from old motor vehicles.

Uses

Iron was not the only metal to be used in Africa; copper and brass were widely utilised too. However the steady spread of iron meant it must have had more favourable properties for many different uses. Its durability over copper meant that it was used to make many tools from farming pieces to weaponry. Iron was used for personal adornment in jewelry, impressive pieces of artwork and even instruments. It was used for coins and currencies of varying forms. For example, kisi pennies; a traditional form of iron currency used for trading in West Africa. They are twisted iron rods ranging from <30 cm to >2m in length. Suggestions for their uses vary from marital transactions, or simply that they were a convenient shape for transportation, melting down and reshaping into a desired object. There are many different forms of iron currency, often regionally differing in shape and value. Iron did not replace other materials, such as stone and wooden tools, but the quantity of production and variety of uses met were significantly high by comparison.

Social and cultural significance

It is important to recognize that while iron production had great influence over Africa both culturally in trade and expansion (Martinelli, 1993, 1996, 2004), as well as socially in beliefs and rituals, there is great regional variation. Much of the evidence for cultural significance comes from the practises still carried out today by different African cultures. Ethnographical information has been very useful in reconstructing the events surrounding iron production in the past, however the reconstructions could have become distorted through time and influence by anthropologist's studies.

L The control of iron production was often by ironworkers themselves, or a "central power" in larger societies such as kingdoms or states (Barros 2000, p. 154). The demand for trade is believed to have resulted in some societies working only as smelters or smiths, specialising in just one of the many skills necessary to the production process. It is possible that this also led to tradesmen specialising in transporting and trading iron (Barros 2000, pg152). However, not every region benefited from industrialising iron production, others created environmental problems that arose due to the massive deforestation required to provide the charcoal for fuelling furnaces (for example the ecological crisis of the Mema Region (Holl 2000, pg48)).

Iron smelters and smiths received different social status depending on their culture. Some were lower in society due to the aspect of manual labour and associations with witchcraft, for example in the Maasai and Tuareg (Childs et al. 2005 pg 288). In other cultures the skills are often passed down through family and would receive great social status (sometimes even considered as witchdoctors) within their community. Their powerful knowledge allowed them to produce materials on which the whole community relied. In some communities they were believed to have such strong supernatural powers that they were regarded as highly as the king or chief. For example, an excavation at the royal tomb of King Rugira (Great Lakes, Eastern Africa) found two iron anvils placed at his head (Childs et al. 2005, p. 288 in Herbert 1993:ch.6). In some cultures mythical stories have been built around the premise of the iron smelter emphasising their godlike significance.

Rituals

The smelting process was often carried out away from the rest of the community. Ironworkers engaged in rituals designed to encourage good production and to ward off bad spirits, including song and prayers, plus the giving of medicines and sacrifices. The latter were usually put in the furnace itself or buried under the base of the furnace. Examples of these date back as far as the early Iron Age in Tanzania and Rwanda (Schmidt 1997 in Childs et al., 2005 p. 293).

Some cultures associated sexual symbolism with iron production. Smelting was integrated with the fertility of their society, The production of the bloom was compared to human conception and birth. There were sexual taboos surrounding the process. The smelting process was carried out entirely by men and often away from the village. For women to touch any of the materials or be present could jeopardise the success of the production. The furnaces were also often adorned to resemble a woman, the mother of the bloom.

See also

* Copper metallurgy in Africa
* Archaeology of Igbo-Ukwu
* KM2 and KM3 sites
* Bantu expansion

References

Bibliography

MetalAfrica: a Scientific Network on African Metalworking
* Killick, D. 2004. Review Essay: "What Do We Know About African Iron Working?" ''Journal of African Archaeology''. Vol 2 (1) pp. 135–152
* Bocoum, H. (ed.), 2004, ''The origins of iron metallurgy in Africa – New lights on its antiquity'', H. Bocoum (ed.), UNESCO publishing
* Schmidt, P.R., Mapunda, B.B., 1996. "Ideology and the Archaeological Record in Africa: Interpreting Symbolism in Iron Smelting Technology". ''Journal of Anthropological Archaeology''. Vol 16, pp. 73–102
* Rehren, T., Charlton, M., Shadrek, C., Humphris, J., Ige, A., Veldhuijen, H.A. "Decisions set in slag: the human factor in African iron smelting". La Niece, S., Hook, D., and Craddock, P., (eds). ''Metals and mines : studies in archaeometallurgy''. 2007, pp. 211–218.
* Okafor, E.E., 1993. "New Evidence on Early Iron-Smelting from Southeastern Nigeria". Shaw, T., Sinclair, P., Bassey, A., Okpoko, A (eds). ''The Archaeology of Africa Food, Metals and Towns''. London, Routledge, pp. 432–448
* Kense, F.J., and Okora, J.A., 1993. "Changing Perspectives on Traditional Iron Production in West Africa". Shaw, T., Sinclair, P., Bassey, A., Okpoko, A (eds). ''The Archaeology of Africa Food, Metals and Towns''. London, Routledge, pp. 449– 458
* Muhammed, I.M., 1993. "Iron Technology in the Middle Sahel/Savanna: With Emphasis on Central Darfur". Shaw, T., Sinclair, P., Bassey, A., Okpoko, A (eds). ''The Archaeology of Africa Food, Metals and Towns''. London, Routledge, pp. 459–467
* Buleli, N'S., 1993. Iron-Making Techniques in the Kivu Region of Zaire: Some of the Differences Between the South Maniema Region and North Kivu. Shaw, T., Sinclair, P., Bassey, A., Okpoko, A (eds). ''The Archaeology of Africa Food, Metals and Towns''. London, Routledge, pp. 468–477
* Radimilahy, C., 1993 "Ancient Iron-Working in Madagascar". Shaw, T., Sinclair, P., Bassey, A., Okpoko, A (eds). ''The Archaeology of Africa Food, Metals and Towns''. London, Routledge, pp. 478–473
* Kiriama, H.O., 1993. "The Iron Using Communities in Kenya". Shaw, T., Sinclair, P., Bassey, A., Okpoko, A (eds). ''The Archaeology of Africa Food, Metals and Towns''. London, Routledge, pp. 484–498
* Martinelli, B., 1993, "Fonderies ouest-africaines. Classement comparatif et tendances", in ''Atouts et outils de l'ethnologie des techniques – Sens et tendance en technologie comparée, Revue Techniques et culture'', n^o 21 : 195–221.
* Martinelli, B., 2004, "On the Threshold of Intensive Metallurgy – The choice of Slow Combustion in the Niger River Bend (Burkina Faso and Mali)" ''in The origins of iron metallurgy in Africa – New lights on its antiquity'', H. Bocoum (ed.), UNESCO publishing : pp. 216–247
* Collet, D.P., 1993. "Metaphors and Representations Associated with Precolonial Iron-Smelting in Eastern and Southern Africa". Shaw, T., Sinclair, P., Bassey, A., Okpoko, A (eds). ''The Archaeology of Africa Food, Metals and Towns''. London, Routledge, pp. 499–511

Further reading

*

{{Three-age system

History of Africa
Science and technology in Africa
History of metallurgy
+
+
+
+
Iron Age Africa
Iron Age