Valve Audio Amplifier

A valve audio amplifier ( UK) or vacuum tube audio amplifier ( US) is a valve amplifier used for sound reinforcement, sound recording and reproduction.

Until the invention of solid state devices such as the transistor, all electronic amplification was produced by valve (tube) amplifiers. While solid-state devices prevail in most audio amplifiers today, valve audio amplifiers are still used where their audible characteristics are considered pleasing, for example in music performance or music reproduction.

Instrument and vocal amplification

Valve amplifiers for guitars (and to a lesser degree vocals and other applications) have different purposes from those of hi-fi amplifiers. The purpose is not necessarily to reproduce sound as accurately as possible, but rather to fulfill the musician's concept of what the sound should be. For example, distortion is almost universally considered undesirable in hi-fi amplifiers but may be considered a desirable characteristic in performance.

Small signal circuits are often deliberately designed to have very high gain, driving the signal far outside the linear range of the tube circuit, to deliberately generate large amounts of harmonic distortion. The distortion and overdrive characteristics of valves are quite different from transistors (not least the amount of voltage headroom available in a typical circuit) and this results in a distinctive sound. Amplifiers for such performance applications typically retain tone and filter circuits that have largely disappeared from modern hi-fi products. Amplifiers for guitars in particular may also include a number of "effects" functions.

The origins of electric guitar amplification

The electric guitar originates from Rickenbacker in the 1930s but its modern form was popularised by Fender and Gibson (notably the Fender Telecaster (1951) & Stratocaster (1954) and Gibson Les Paul (1952) during the 1950s. The earliest guitar amplifiers were probably audio amplifiers made for other purposes and pressed into service, but the electric guitar and its amplification quickly developed a life of its own, supported by specialist manufacturers.

Guitar amplifiers are often designed so they can, when desired by the guitarist, distort and create a tone rich in harmonics and overtones. The characteristics of the tube and the circuit directly influence the nature of the sound produced. Even the power supply can influence the tonal shape, with relatively undersized power supply capacitors producing a characteristic "sag" at instants of peak output and power draw, and subsequent recovery, that is often considered musically engaging. In addition, guitarists may employ acoustic feedback, further modifying the resulting sound (noting that the feedback signal has a slight time lag relative to the original signal).

Guitar amplifiers are typically designed to withstand a lot of abuse both electrically and physically (since guitarists often travel to gigs, etc.) In large systems the amplifier is separate from the speaker enclosure(s), but in smaller systems it is often integrated, forming a so-called "combo". Since the amplifier is usually at the top of the combo, the tubes often hang upside down facing the body of the enclosure. They may be held in with clips.

Most modern valve guitar amplifiers use a class AB1 push-pull circuit with a pair of power pentodes or beam tetrodes, 6L6 or EL34 but occasionally KT88, 6550, or the lower-power EL84 in '' Ultra-Linear'' connection. The output stage is preceded by a voltage amplification stage (pentode or twin triode) and a phase-splitter (twin triode). Twin triodes with two identical sections in one envelope are used, usually the noval types 12AT7, 12AU7, or 12AX7 or equivalents, less usually the octal 6SN7.

Amplifiers for sound reproduction

Early development

The earliest mass usage of valve audio amplifiers was for telephony. Valve amplifiers were critical in development of long-distance telephone circuits and submarine telephone cables. Radio applications followed soon after, where valves were used for both the audio (AF) and radio (RF) circuitry. (RF is outside the scope of this article, see valve amplifier).

Among the first applications of sound recording and electronic replay around the 1920s was its use in many cinemas equipping for exhibiting the new 'talkies'. Cinema sound systems of this period were predominantly supplied by "Westrex", related to the Western Electric company, a telecoms supplier, who were also the makers of the 300B DHT tube that today is central to current production DH-SET audiophile amplification.

Amplifiers during this period typically used Directly Heated tubes in a Class A Single-Ended Triode circuit. Power output ranged from a few watts to perhaps 20 watts for an exceptionally powerful amplifier (modern semiconductor amplifiers produce much higher power). Today this type of circuit retains a niche following at the very extreme of audiophile hi-fi, where it is often referred as DH-SET.

Prior to WWII, almost all electronic amplifiers were triodes used without feedback. The inherent, albeit imperfect, linearity of tubes makes it possible to get acceptable distortion performance without correction. Amplitude distortion in a class A triode stage can be small if care is taken to prevent the anode current from becoming too small and ensuring that grid current does not flow at any point. In this case, distortion is largely relatively unobjectionable second harmonic, with percentage closely proportional to the output amplitude. Adding modest negative feedback improves linearity further. Pentodes of the same power dissipation are capable of higher output power than triodes, but distortion is higher and more objectionable.

The 1940s and 1950s

During the post-war period, widespread adoption of negative feedback in the push pull topology yielded greater power and linearity, notably following the publication in 1947 of the Williamson amplifier, which set the standard (and the dominant topology) for what was to follow.

Widespread adoption of push pull allowed smaller (and thus cheaper) transformers, combined with more power (typically 10 to 20 watts) to handle peaks. The high fidelity industry was born.

Other developments included (among others):
* the introduction of the "Point One" series of amplifiers (in 1945) by LEAK in the UK, which first set a performance standard of 0.1% THD
* the Ultra-Linear output stage (a tapped push-pull output transformer providing power intermediate between triodes and pentodes, at lower distortion than either) was originated by Alan Blumlein in 1937 in the UK, but popularised following publication of a paper by David Hafler and Keroes in the USA in 1951, and became the dominant topology during the post war recovery of consumer products
* Manufacturers bringing high-quality domestic hi-fi to a steadily widening audience, eventually leading to Dynaco selling over 300,000 ST-70's, making it the world's most popular hi-fi amplifier of any type to date.

Tube hi-fi in the 1960s

Valve amplification peaked as the mainstream technology during the 1960s and 70s, with device and circuits being highly developed. There have been only minor refinements since then.

The last generation of power tubes, typified by KT66, EL34 and KT88, represent the pinnacle of the technology and of production quality. Valve amplifiers produced since that time usually use one of these tubes, which have remained in continuous production (apart from KT66) ever since. Output power was typically 20 watts, exceptionally 35W.

Small signal valves overwhelmingly changed from octal base tubes, notably the audio tube of choice, the 6SN7 family, to the smaller and cheaper noval base ECC81, ECC82, ECC83 (UK, in the US known as 12AX7,12AT7, etc.). The lower-power noval base EL84 power pentode was widely used in less expensive 10-watt ultralinear power amplifiers, still of high fidelity.

Commercial tube manufacturers developed designs based on their own products, most notably the Mullard 5-10 circuit. This design and the Williamson were widely implemented and imitated, with or without crediting the originator.

Automobile amplifiers

Valve radios and amplifiers were used in automobiles until they were displaced by transistorized radios. Transistors had the major advantage of working off the voltage provided by a car battery. Early radios required a power unit to convert the battery voltage to a value high enough for the valves. Later radios used special valves that were designed to operate directly from a 12 volt supply.Mullard ECH83, EBF83 are but two such examples. These later radios were hybrid designs which used transistors only for the audio output stages because a 12 volt power amplifier valve was not practical. For this and other applications, transistors are smaller, cheaper, more durable, use less power, run cooler, and do not need to warm up.

Some enthusiasts prefer "tube amps", so a small number of valve car stereos are still made. Manufacturers include Milbert Amplifiers, Blade, Manley, and Sear Sound. Some are hybrid designs with transistors and valves.

Valve preamplifiers

Due to the very poor technical performance of early gramophones, the lack of standardised equalisations, poor components and accessories (including loudspeakers), preamplifiers historically contained extensive and very flexible equalization and tone and filter circuits designed to adjust the frequency response of the amplifier and so the sound produced by the system.

Valve preamplifiers use triodes or low-noise pentodes ( EF86). Mains hum from the heater filaments is a potential problem in low-level valve stages. Modern amplifiers invariably run from the mains; as there is little need to minimise costs in expensive valve amplifiers, the heater supply is often rectified and even regulated to reduce hum to an absolute minimum.

A representative valve preamp from the 1950s is the Leak 'varislope' series of preamps, which included a switchable rumble filter, a switchable scratch filter with selectable slopes and corner frequency, continuously variable treble and bass tone controls and a selection of 4 different gramophone equalisations (RIAA, ortho, RCA, 78).

Valve sound

Amplifiers from and prior to this period often have a distinctive sound that today is still widely referred to as "valve sound" and "warm". This tone is not strictly caused by the use of valves rather than transistors; it is merely a sound that was originally associated with amplifiers built using valves simply because that is what was available at the time. The origins of that particular sound are in part due to:
* the typical circuit designs of the time (class A or AB1), combined with
** simple circuits with relatively little feedback, producing mainly low-harmonic distortion (feedback that could be applied was limited by phase shift in the output transformer);
** low damping factor (High Z out) output stages;
** the use of very large amounts of feedback in signal transformerless semiconductor circuits, which leads to distortion that is small but has a much larger proportion of high harmonics than in valve circuits.

Factors relevant to valve equipment not designed to high-fidelity standards:
* dedicated guitar amplifiers had frequency response and distortion suited to their purpose,
* under-dimensioned and unregulated power supplies in amplifiers where power drawn varied significantly with instantaneous power output (class A not affected, classes AB1, AB2, B, increasingly so),
* poor quality output transformers in budget equipment.

Notable historic designs

In addition to a range of commodity valve amplifiers, some amplifiers were made which are still highly regarded today. Among the best known are:
* LEAK TL/12
* Williamson amplifier
* Mullard 5-10
* Quad II
* Dynaco Mark III and Stereo 70
* McIntosh MC275
* Marantz 8B and 9

Valve audio amplifier technical information

Various basic circuits have been used in designs and in various approaches to construction.

See also

* Amplifier
* Audio amplifier
* Valve sound
* Valve amplifier

References

* Valve Amplifiers, Morgan Jones, Third Edition 2003 - about the design and construction of valve audio amplifiers
* Tube Amplifiers, Allegro Verlag, Vienna. - Contains a short introduction, the rest of the book is many photographs of some tube amplifiers.
* Glass Audio. A long running journal devoted to tube amp construction, published by the Audio Amateur (TAA) Corp
* ''Radiotron Designer's Handbook'', Classic Edition, F Langford-Smith et al. First published 1934, revised until 1967ISBN 0 7506 3635 1 - Compendium of articles of historic interest to people in this field
* http://www.stereophile.com/reference/70/ - discussion of the limitations of NFB in audiophile systems


- Theory paper on OTL designs.

External links

Schematic Heaven
— Free schematic archive of vintage guitar amplifier and effect schematics.

The Audio Circuit
- An almost complete list of manufacturers, DIY kits, materials and parts and 'how they work' sections on valve amplifiers.
* {{cite web
, url = http://www.stereophile.com/reference/70
, title = A Future Without Feedback? (A detailed discussion of the limitations of NFB as a panacea)
, website = stereophile.com
, author = Martin Colloms
, date = Jan 3, 1998

Valve amplifiers
Vacuum tubes
Audio amplifiers