Tramway Track

Tramway track is used on tramways or light rail operations. Grooved rails (or girder rails) are often used to provide a protective flangeway in the trackwork in city streets. Like standard rail tracks, tram tracks consist of two parallel steel rails.

Tram rails can be placed on several surfaces, such as with standard rails on sleepers like railway tracks, or with grooved rails on concrete sleepers into street surfaces ( pavement) for street running. Tram rails in street have the disadvantage that they pose a risk to cyclists.
An alternative is to lay tracks into non-road grass turf surfaces; this is known as ''grassed track'' (or ''track in a lawn''), introduced in Liverpool in 1924 - although grassed track is common in rural tramways.

History

Tramway tracks have been in existence since the mid-16th century. They were previously made of wood, but during the late 18th century iron and later steel came into use prominently.

The first street tramways were laid in 1832 in New York by John Stephenson to assist horses pulling buses on dirt roads, especially when the roads were muddy from wet weather. The rails enabled a horse to easily pull a load of 10 tonnes compared to 1 tonne on a dirt road. The evolution of street tramway tracks paralleled the transition from horse power to mechanical and electric power. In a dirt road, the rails needed a foundation, usually a mass concrete raft. Highway authorities often made tramway companies pave the rest of the road, usually with granite or similar stone blocks, at extra cost.

The first tramways had a rail projecting above the road surface, or a step set into the road, both of which were apt to catch the narrow tyres of horse-drawn carriages. The invention by Alphonse Loubat in 1852 of grooved rail enabled tramways to be laid without causing a nuisance to other road users, except unsuspecting cyclists, who could get their wheels caught in the groove.

Grooved rail

A grooved rail, groove rail, or girder rail is a special rail with a groove designed for tramway or railway track in pavement or grassed surfaces (grassed track or track in a lawn). The rail has the railhead on one side and the guard on the other. The guard provides accommodation for the flange. The guard carries no weight, but may act as a checkrail.

Grooved rail was invented in 1852 by Alphonse Loubat, a French inventor who developed improvements in tram and rail equipment, and helped develop tram lines in New York City and Paris. The invention of grooved rail enabled tramways to be laid without causing a nuisance to other road users, except unsuspecting cyclists, who could get their wheels caught in the groove. The grooves may become filled with gravel and dirt (particularly if infrequently used or after a period of idleness) and need clearing from time to time, this being done by a "scrubber" tram. Failure to clear the grooves can lead to a bumpy ride for the passengers, damage to either wheel or rail and possibly derailing.

Girder guard rail

The traditional form of grooved rail is the girder guard section illustrated below. This rail is a modified form of flanged rail and requires a special mounting for weight transfer and gauge stabilisation. If the weight is carried by the roadway subsurface, steel ties are needed at regular intervals to maintain the gauge. Installing these means that the whole surface needs to be excavated and reinstated.

Block rail

Block rail is a lower profile form of girder guard rail, where the web is eliminated. In profile it is more like a solid form of bridge rail with a flangeway and guard added. Simply removing the web and combining the head section directly with the foot section would result in a weak rail, so additional thickness is required in the combined section.

Prefabricated grooved rail

A modern version of the grooved block rail has a lower mass and is inserted into a prefabricated spanning concrete girder such as the LR55 without web but fully supported by noise reducing polyurethane grout or a girder rail such as P-CAT City Metro P-CAT City Metro rail
/ref> is embedded. The prefabricated units if used with ultra light trams can be embedded into existing road base with possibly a reduced requirement for underground services diversions.

Track gauge

Electrification

Electrification needed other developments, most notably heavier rails to cope with electric tramcars weighing 12 tonnes rather than the 4 tonne horse-drawn variety; switching points, as electric trams could not be pulled onto the correct track by horses; and the need for electrical connections, to provide the return path for the electric current, which was usually supplied through an overhead wire.

Conduit and stud systems

In some cities where overhead electric cables were deemed intrusive, underground conduits with electrical conductors were used. Examples of this were New York, Washington DC, Paris, London, Brussels and Budapest. The conduit system of electrical power was very expensive to install and maintain, although Washington did not close until 1962. Attempts were made with alternative systems not needing overhead wires. There were many systems of “surface” contact, where studs were set in the road surface, and energised by a passing tram, either mechanically or magnetically, to supply power through a skate carried under the tram. Unfortunately these systems all failed due to the problem of reliability and not always turning off after the tram had passed, resulting in the occasional electrocution of horses and dogs. In the last five years a new system of surface contact has been installed in the Bordeaux tramway by Alstom.

Cable haulage

Prior to the universal introduction of electric power, many tramways were cable hauled, with a continuous cable carried in a conduit under the road, and with a slot in the road surface through which the tram could clasp the cable for motion. This system can still be seen in San Francisco in California as well as the system of the Great Orme in Wales. These needed a rather more substantial track formation.

Gallery

Image:Mh gleisverschlingung.jpeg, Grooved rail gauntlet track
Image:EuskoTran.jpg, Grassed track
File:San Fernando (VTA) light rail station.jpg, Light rail tracks with concrete railroad ties (sleepers)
File:Workers join tram tracks in Christchurch.jpg, Joining tram tracks using an exothermic weld
File:Tram tracks recently joined.jpg, A rough exothermic weld after removal of the mould
File:Streetcar Track Construction at Bathurst and Queen St. W.jpg, An intersection with the pavement removed, as workers repair the tracks for the Toronto streetcar system.
Image:Szyny Głogowska RB2.JPG, Cross section of a grooved tram rail
Image:TreinTramwielprofiel.svg, Difference in form and profile of the wheel and the rail of a train (left, blue) and a tram (right, green)
See Railway wheel flange
Image:20180711 aiguillage californien at Bailli 2.jpg, Temporary or "Californian" points installed on tramline 81 at junction of Avenue Louise and Rue Bailli, Brussels, on 11 July 2018
File:Tram track washing machine in Riga.jpg, A specialised vehicle washing the tramway track in Riga, Latvia

See also

* Difference between train and tram rails
* Grade (slope)
* Gauntlet track
* Minimum railway curve radius
* Rail profile
* Railroad switch (points)
* Railway guide rail
* Reserved track
* Street running
* Track transition curve
* Tram track gauge
* Tramway (industrial)

References

External links

LR55 Track System Full detailsLR55 track suppliers and advisers


* ttp://interfacejournal.com/archives/472 Testing Girder Rail on the MBTA.
Wirth Girder Rail



MRT Track & Services Co., Inc / Krupp, T and girder rails, scroll down.


* ttps://archive.today/20140415230744/http://www.tkgftgleistechnik.de/en/railway_track_manual/oberbaustoffe/schienen/rillenschienen.html ThyssenKrupp grooved rail*

{{Authority control

Permanent way
Tram technology